Generated by kicad-footprint-generator · KiCad file format 20260206
TPS65162RGZR
Texas Instruments · LCD Drivers · VQFN-48-EP(7x7)
TPS65162RGZR from Texas Instruments, in a VQFN-48-EP(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | POS1 | input | Non-inverting input of operational amplifier 1. |
| 2 | OUT1 | output | Output of operational amplifier 1. |
| 3 | VDD | power_in | Gate voltage shaping threshold pin: five times the voltage applied to this pin sets the discharge threshold for the gate voltage shaping function. |
| 4 | CE | input | Sets the delay between the falling edge of VFLK and the falling edge of VGHM for gate voltage shaping. |
| 5 | VFLK | input | Control input for gate voltage shaping, with VIH of 1.7 V minimum and VIL of 0.4 V maximum. |
| 6 | VDPM | input | Enable input for the gate voltage shaping block, with VIH of 2.0 V minimum and VIL of 0.8 V maximum. |
| 7 | RE | output | Slope adjustment of gate voltage shaping; a resistor connected to this pin adjusts the slope. |
| 8 | VGHM | output | Output of the gate voltage shaping block. |
| 9 | VGH | input | High-voltage input for the gate voltage shaping block; connect the positive charge-pump output to this pin. |
| 10 | FBP | input | Feedback input of the positive charge pump, regulated to a VFB of 1.265 V typical. |
| 11 | GND | power_in | Ground for the positive and negative charge pumps. |
| 12 | DRVP | output | Drive pin of the positive charge pump. |
| 13 | SUP | power_in | Supply pin of the positive charge pump; absolute maximum rating is 25 V. |
| 14 | DRVN | output | Drive pin of the negative charge pump. |
| 15 | AGND | power_in | Analog ground. |
| 16 | FBN | input | Feedback input of the negative charge pump, with VFB regulation of 0 V nominal (±48 mV). |
| 17 | REF | output | Internal reference output; connect a 220-nF capacitor directly from this pin to AGND to minimize noise coupling. |
| 18 | DLY1 | output | A capacitor from this pin to GND sets the delay between the step-down converter and the negative charge pump VGL. |
| 19 | NC | unconnected | Not connected. |
| 20 | NC | unconnected | Not connected. |
| 21 | FBB | input | Feedback input of the buck converter. |
| 22 | CBOOT | input | N-channel MOSFET gate drive voltage for the buck converter; connect a capacitor from this pin to SWB. |
| 23 | SWB | output | Switch pin of the buck converter. |
| 24 | SWB | output | Switch pin of the buck converter. |
| 25 | PVIN | power_in | Power input for the buck converter; recommended input voltage range is 8 V to 14.7 V. |
| 26 | PVIN | power_in | Power input for the buck converter; recommended input voltage range is 8 V to 14.7 V. |
| 27 | VIN | power_in | Analog input voltage of the device; bypass with a 1-µF capacitor for good filtering. |
| 28 | FREQ | input | Frequency selection: FREQ high gives 750 kHz operation and FREQ low gives 500 kHz operation. |
| 29 | DLY2 | output | A capacitor from this pin to GND sets the delay between the step-down converter and the positive charge pump VGH. |
| 30 | SS | output | Soft-start of the boost converter; connect a capacitor from this pin to GND. |
| 31 | VC | output | Compensation pin of the boost converter. |
| 32 | EN2 | input | Enable pin of the boost converter block. |
| 33 | EN1 | input | Enables the buck converter and, after a delay set by DLY1, the negative charge pump; logic high enables the device and logic low shuts it down. |
| 34 | PGND1 | power_in | Power ground; the thermally enhanced PowerPAD is connected to PGND1. |
| 35 | PGND2 | power_in | Ground for the boost converter. |
| 36 | PGND3 | power_in | Power ground pin; the datasheet gives no separate function for this pin beyond the terminal table entry. |
| 37 | SW | input | Switch pin of the boost converter. |
| 38 | SW | input | Switch pin of the boost converter. |
| 39 | SWI | input | Input of the isolation switch, connected to the internal overvoltage protection comparator. |
| 40 | NC | unconnected | Not connected. |
| 41 | FB | input | Feedback input of the boost converter that generates Vs. |
| 42 | SWO | output | Output of the isolation switch. |
| 43 | AVIN | power_in | Power input for the operational amplifiers; connect to the isolation switch input SWI and bypass with a 1-µF capacitor. |
| 44 | NEG2 | input | Inverting input of operational amplifier 2. |
| 45 | POS2 | input | Non-inverting input of operational amplifier 2. |
| 46 | OUT2 | output | Output of operational amplifier 2. |
| 47 | OGND | power_in | Ground for the operational amplifiers. |
| 48 | NEG1 | input | Inverting input of operational amplifier 1. |
| 49 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | VQFN-48-EP(7x7) |
| Category | Nixie Tube Driver/LED Driver |
| Pins | 49 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input voltage range VIN, PVIN (absolute maximum) | VIN, PVIN | -0.3 | 16.8 | V | 2 | ||
| Voltage range at EN1, EN2, FREQ, VDPM, VFLK | -0.3 | 16.8 | V | 2 | |||
| Voltage on pin AVIN, SUP | 25 | V | 2 | ||||
| Voltage on pin VGH, VGHM, RE | 35 | V | 2 | ||||
| Voltage on pin SW, SWI, SWO | 25 | V | 2 | ||||
| Voltage on pin SWB | 20 | V | 2 | ||||
| Operating junction temperature range | TJ | -40 | 150 | °C | 2 | ||
| Operating ambient temperature range | TA | -65 | 85 | °C | 2 | ||
| Storage temperature range | Tstg | -65 | 150 | °C | 2 | ||
| Input voltage range VIN, PVIN (recommended) | VIN, PVIN | 8 | 14.7 | V | 2 | ||
| Operating ambient temperature (recommended) | TA | -40 | 85 | °C | 2 | ||
| Operating junction temperature (recommended) | TJ | -40 | 125 | °C | 2 | ||
| Input voltage range | VI | 8 | 14.7 | V | 3 | ||
| Shutdown current into VIN | ISD | 0.03 | 1 | μA | EN1 = EN2 = GND | 3 | |
| Quiescent current into VIN | IQIN | 1.7 | 4 | mA | 3 | ||
| Quiescent current into AVIN | IAVIN | 8 | 10 | mA | 3 | ||
| Undervoltage lockout threshold | VUVLO | 7.6 | 7.95 | V | VIN falling | 3 | |
| Reference voltage | VREF | 1.253 | 1.265 | 1.277 | V | 3 | |
| High level input voltage EN1, EN2, VDPM, FREQ | VIH | 2 | V | 3 | |||
| Low level input voltage EN1, EN2, VDPM, FREQ | VIL | 0.8 | V | 3 | |||
| High level input voltage VFLK | VIH | 1.7 | V | 3 | |||
| Low level input voltage VFLK | VIL | 0.4 | V | 3 | |||
| DLY1, DLY2 charge current | Ichrg | 3.5 | 5 | 6 | μA | Vthreshold = 1.280 V | 3 |
| SS charge current | ISS | 6 | 9.2 | 12 | μA | 3 | |
| Oscillator frequency | fS | 600 | 750 | 900 | kHz | FREQ = high | 3 |
| Oscillator frequency | fS | 400 | 500 | 600 | kHz | FREQ = low | 3 |
| Boost converter output voltage range | VS | 19 | V | 3 | |||
| Boost feedback regulation voltage | VFB | 1.255 | 1.268 | 1.28 | V | 3 | |
| N-MOSFET on-resistance (Q1), boost | rDS(on) | 130 | 200 | mΩ | Vs = 15 V, I(SW) = 500 mA | 3 | |
| P-MOSFET on-resistance (Q2), boost | rDS(on) | 9 | 15 | Ω | Vs = 15 V,I(SW) = 200 mA | 3 | |
| Maximum P-MOSFET peak switch current | IMAX | 1 | A | 3 | |||
| N-MOSFET switch current limit (Q1), boost | ILIM | 2.8 | 3.6 | 4.2 | A | 3 | |
| Switch overvoltage protection | V(SW_ovp) | 19.5 | 20 | 21 | V | VOUT rising | 3 |
| Isolation switch rDS(on) | rDS(on) | 200 | mΩ | I(SW) = 1 A, Vs = 15 V | 3 | ||
| Input voltage (gate voltage shaping) | VHVIN | 35 | V | 4 | |||
| VGH to VGHM rDS(on) (Q1) | rDS(on) | 10 | 15 | Ω | VFLK = high, I = 20 mA | 4 | |
| VGHM to RE rDS(on) | rDS(on) | 60 | 100 | Ω | VFLK = LOW, I = 20 mA | 4 | |
| CE capacitor charge current | ICE | 44 | 57 | 65 | μA | VCE = 1.265 V | 4 |
| Step-down converter output voltage range | Vlogic | 1.5 | 5 | V | 4 | ||
| Step-down feedback regulation voltage | VFB | 1.24 | 1.265 | 1.29 | V | 4 | |
| N-MOSFET on-resistance (Q1), step-down | rDS(on) | 180 | 320 | mΩ | PVIN = 12 V, I(SW) = 500 mA | 4 | |
| N-MOSFET switch current limit (Q1), step-down | ILIM | 2.8 | 3.6 | 4.2 | A | 4 | |
| Negative charge pump output voltage range | VGL | -2 | V | 4 | |||
| Negative charge pump feedback regulation voltage | VFB | -48 | 0 | 48 | mV | 4 | |
| Q4 P-channel switch rDS(on) | rDS(on) | 4 | 8 | Ω | IO = 20 mA | 4 | |
| Current source voltage drop (negative pump) | VDropN | 115 | 200 | mV | I(DRVN) = 50 mA, V(FBN) = V(FBN_nominal) -5% | 4 | |
| Current source voltage drop (negative pump) | VDropN | 230 | 400 | mV | I(DRVN) = 100 mA, V(FBN) = V(FBN_nominal) -5% | 4 | |
| Positive charge pump output voltage range | VGH | 34 | V | 4 | |||
| Positive charge pump feedback regulation voltage | VFB | 1.228 | 1.265 | 1.302 | V | 4 | |
| Q3 N-channel switch rDS(on) | rDS(on) | 1 | 1.8 | Ω | IOUT = 20 mA | 4 | |
| Current source voltage drop (positive pump) | VDropP | 430 | 680 | mV | IDRP = 50 mA, VFBP = VFBP_nominal -5% | 4 | |
| Current source voltage drop (positive pump) | VDropP | 950 | 1600 | mV | IDRP = 100 mA, VFBP = VFBP_nominal -5% | 4 | |
| Op-amp input offset voltage | Vos | -15 | 18 | mV | VCM = Vs/2 | 4 | |
| Op-amp common mode input voltage range | VCM | 0 | V | 4 | |||
| Op-amp common mode rejection ratio | CMRR | 70 | dB | VCM = 7.5 V | 4 | ||
| Op-amp open loop gain | AVOL | 50 | dB | 0.5 V ≤ VOUT ≤ 14.5 V, No load | 4 | ||
| Op-amp short circuit current | Isc | 120 | 215 | mA | 4 | ||
| Op-amp output current | Io | 90 | 170 | mA | VOUT = 7.5 V, Input offset voltage 10 mV | 4 | |
| Op-amp power supply rejection ratio | PSRR | 80 | dB | 4 | |||
| Thermal resistance junction-to-ambient, 48-pin QFN | RθJA | 30 | °C/W | 2 |
CAD (KiCad official)
- Symbol:
TPS65162RGZR - Footprint:
Package_DFN_QFN:QFN-48-1EP_7x7mm_P0.5mm_EP5.15x5.15mm - 3D model: VQFN-48-EP(7x7) (KiCad packages3D, STEP)
- 3D model files:
tps65162rgzr-etched.step/tps65162rgzr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);tps65162rgzr.step/tps65162rgzr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (38 pp, sha256
921e37c5bfd6fb38, retrieved 2026-10-28, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).