3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownTPS62933DRLR
Texas Instruments · DC-DC Converters · SOT-583
TPS62933DRLR from Texas Instruments, in a SOT-583. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). The symbol is generated from that pin table, the footprint is an Adom_Gen land derived from the manufacturer drawing, and the 3D model is generated to fit it.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | RT | input | Frequency programming input: float for 500 kHz, tie to GND for 1.2 MHz, or connect a timing resistor to set 200 kHz to 2.2 MHz. |
| 2 | EN | input | Enable input; driving EN high or leaving it floating enables the converter, and an external resistor divider can set an adjustable VIN UVLO. |
| 3 | VIN | power_in | Supply input to the internal LDO and high-side FET; input bypass capacitors must connect directly to this pin and GND, with a 3.8-V to 30-V recommended input range. |
| 4 | GND | power_in | Ground pin connected to the low-side FET source and controller ground; the path to CIN must be as short as possible. |
| 5 | SW | output | Switching output connected to the power inductor, internally tied to the high-side FET source and low-side FET drain; recommended DC range is -0.1 V to 30 V. |
| 6 | BST | passive | Bootstrap capacitor connection for the high-side FET driver; connect a high-quality 100-nF ceramic capacitor from this pin to SW. |
| 7 | SS | input | Soft-start control pin for this variant; a minimum 6.8-nF ceramic capacitor sets the minimum soft-start time to approximately 1 ms, and the pin must not float. |
| 8 | FB | input | Output feedback input; connect to the tap of an external resistor divider from the output to GND to set the output voltage. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | SOT-583 |
| Category | Power Management (PMIC) |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input voltage | VIN | -0.3 | 32 | V | 5 | ||
| EN voltage | EN | -0.3 | 6 | V | 5 | ||
| FB voltage | FB | -0.3 | 6 | V | 5 | ||
| SW DC voltage | SW | -0.3 | 32 | V | DC | 5 | |
| SW transient voltage | SW | -3 | 33 | V | transient < 10 ns | 5 | |
| BST voltage | BST | -0.3 | V | max printed as SW + 6 | 5 | ||
| BST-SW voltage | BST-SW | -0.3 | 6 | V | 5 | ||
| SS/PG voltage | SS/PG | -0.3 | 6 | V | 5 | ||
| RT voltage | RT | -0.3 | 6 | V | 5 | ||
| Operating junction temperature | TJ | -40 | 150 | °C | 5 | ||
| Storage temperature | Tstg | -65 | 150 | °C | 5 | ||
| Input voltage | VIN | 3.8 | 30 | V | 5 | ||
| EN voltage | EN | -0.1 | 5.5 | V | 5 | ||
| FB voltage | FB | -0.1 | 5.5 | V | 5 | ||
| PG voltage | PG | -0.1 | 5.5 | V | 5 | ||
| Output voltage | VOUT | 0.8 | 22 | V | 5 | ||
| SW DC voltage | SW | -0.1 | 30 | V | DC | 5 | |
| SW transient voltage | SW | -3 | 32 | V | transient < 10 ns | 5 | |
| BST voltage | BST | -0.1 | V | max printed as SW + 5.5 | 5 | ||
| BST-SW voltage | BST-SW | -0.1 | 5.5 | V | 5 | ||
| Output current | IOUT | 0 | 3 | A | TPS62933, TPS62933x | 5 | |
| Operating junction temperature | TJ | -40 | 150 | °C | 5 | ||
| Junction-to-ambient thermal resistance | RθJA | 112.2 | °C/W | JEDEC board, DRL (SOT583) 8 pins | 6 | ||
| Junction-to-case (top) thermal resistance | RθJC(top) | 29.1 | °C/W | DRL (SOT583) 8 pins | 6 | ||
| Junction-to-ambient thermal resistance on official EVM board | RθJA_EVM | 60.2 | °C/W | official EVM board, 2 layer, 2-oz copper | 6 | ||
| VIN operation input voltage | VIN | 3.8 | 30 | V | 6 | ||
| Input undervoltage lockout rising threshold | VIN_UVLO | 3.4 | 3.6 | 3.8 | V | Rising threshold | 6 |
| Input undervoltage lockout falling threshold | VIN_UVLO | 3.1 | 3.3 | 3.5 | V | Falling threshold | 6 |
| Input undervoltage lockout hysteresis | VIN_UVLO | 300 | mV | Hysteresis | 6 | ||
| Nonswitching quiescent current | IQ | 12 | µA | EN = 5 V, VFB = 0.85 V, TPS62932, TPS62933, TPS62933P | 6 | ||
| Shutdown supply current | ISHDN | 2 | µA | VEN = 0 V | 6 | ||
| Enable threshold rising | VEN_RISE | 1.21 | 1.28 | V | Rising enable threshold | 6 | |
| Disable threshold falling | VEN_FALL | 1.1 | 1.17 | V | Falling disable threshold | 6 | |
| FB voltage | VFB | 792 | 800 | 808 | mV | TJ = 25°C | 6 |
| FB voltage | VFB | 788 | 800 | 812 | mV | TJ = 0°C to 85°C | 6 |
| FB voltage | VFB | 784 | 800 | 816 | mV | TJ = -40°C to 150°C | 6 |
| FB input leakage current | IFB | 0.15 | µA | VFB = 0.8 V | 6 | ||
| High-side MOSFET on-resistance | RDSON_HS | 76 | mΩ | TJ = 25°C, VBST - SW = 5 V | 6 | ||
| Low-side MOSFET on-resistance | RDSON_LS | 32 | mΩ | TJ = 25°C | 6 | ||
| High-side MOSFET current limit | IHS_LIMIT | 4.2 | 5 | 5.8 | A | TPS62933 and TPS62933x | 6 |
| Low-side MOSFET current limit | ILS_LIMIT | 2.9 | 3.8 | 4.5 | A | TPS62933 and TPS62933x | 7 |
| Minimum peak inductor current | IPEAK_MIN | 0.75 | A | TPS62933, TPS62933P, and TPS62933O | 7 | ||
| Soft-start charge current | ISS | 4.5 | 5.5 | 6.5 | µA | TPS62932, TPS62933, and TPS62933F | 7 |
| Switching center frequency | fSW | 450 | 500 | 550 | kHz | RT = floating | 7 |
| Switching center frequency | fSW | 1000 | 1200 | 1350 | kHz | RT = GND | 7 |
| Switching frequency with timing resistor | fSW | 310 | kHz | RT = 71.5 kΩ | 7 | ||
| Switching frequency with timing resistor | fSW | 2100 | kHz | RT = 9.09 kΩ | 7 | ||
| Minimum ON pulse width | tON_MIN | 70 | ns | 7 | |||
| Minimum OFF pulse width | tOFF_MIN | 140 | ns | 7 | |||
| Maximum ON pulse width | tON_MAX | 7 | µs | 7 | |||
| Output OVP threshold | VOVP | 112 | 115 | 118 | % | OVP detect (L→H) | 7 |
| Output OVP hysteresis | VOVP | 5 | % | Hysteresis | 7 | ||
| Output UVP threshold | VUVP | 65 | % | UVP detect (H→L) | 7 | ||
| UV hiccup ON time | thiccup_ON | 256 | µs | before entering hiccup mode after soft start ends | 7 | ||
| Thermal shutdown threshold | TSHDN | 165 | °C | Shutdown temperature | 7 | ||
| Thermal shutdown hysteresis | THYS | 30 | °C | Hysteresis | 7 | ||
| Internal spread oscillator frequency | fspread | -6 | 6 | % | ±6% | 8 |
CAD (Adom-generated)
- Symbol:
TPS62933DRLR - Footprint:
Adom_Gen:Texas_Instruments_TPS62933_f27935 - 3D model: generated to fit the land (STEP)
- 3D model files:
tps62933drlr-etched.step/tps62933drlr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);tps62933drlr.step/tps62933drlr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (51 pp, sha256
16ec2eac43c7374e, retrieved 2026-11-17, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: symbol generated from the datasheet pin table; footprint an Adom_Gen land derived from the manufacturer drawing; 3D model generated to fit that land.