main
History Download
Ray Publish 0.1.0 f92db38

TPS62913RPUR

Texas Instruments · DC-DC Converters · VQFN-10-HR(2x2)

TPS62913RPUR from Texas Instruments, in a VQFN-10-HR(2x2). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). The symbol is generated from that pin table, the footprint is an Adom_Gen land derived from the manufacturer drawing, and the 3D model is generated to fit it.

Pinout

Pin Name Type Function
1 EN/SYNC input Enable/disable pin with threshold comparator: logic low disables the device, pulling it high enables it, it has an internal pulldown of typically 500 kΩ when disabled, and applying a clock synchronizes the device.
2 SW bidirectional Switch pin of the power stage.
3 VO input Output voltage sense pin that needs to be connected directly after the first inductor.
4 PGND power_in Power ground connection.
5 PG output Open-drain power-good output that is pulled to GND when VOUT is below the power-good threshold, requires a pullup resistor for a logic high, and can be left open or tied to GND if not used.
6 VIN power_in Power supply input voltage pin.
7 PSNS input Power sense ground that must be connected directly to the ground plane.
8 NR/SS output A capacitor connected to this pin sets the soft-start time and the low-frequency noise level of the device.
9 FB input Feedback pin of the device.
10 S-CONF output Smart Configuration pin that configures the operation modes of the device, as described in Table 7-1.

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package VQFN-10-HR(2x2)
Category Power Management (PMIC)
Pins 10

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Voltage VIN, EN/SYNC, PG, S-CONF -0.3 18 V 4
Voltage SW AC -2.5 21 V less than 10 ns, while switching 4
Voltage VO, FB, NR/SS -0.3 6 V 4
Voltage PSNS -0.3 0.3 V 4
Sink current PG 10 mA 4
Junction temperature TJ -40 150 °C 4
Storage temperature Tstg -65 150 °C 4
Input voltage VIN 3 17 V 4
Output voltage VOUT 0.8 5.5 V 4
Effective input capacitance CIN 5 10 µF 4
Effective output inductance tolerance L1 -30 20 % nominal 2.2 / 4.7 µH 4
Effective output capacitance COUT 40 47 80 µF 4
Effective filter inductance Lf 0 10 50 nH 4
Effective filter capacitance Cf 20 40 160 µF 4
Effective total output capacitance COUT + Cf 40 200 µF 4
Output current IOUT 0 3 A for TPS62913 4
Junction temperature operating TJ -40 150 °C 4
Junction-to-ambient thermal resistance RθJA 87.7 °C/W JEDEC 51-7 board 5
Junction-to-ambient thermal resistance RθJA 56.6 °C/W PCB TPS6291xEVM-077 5
Junction-to-case (top) thermal resistance RθJC(top) 61.9 °C/W 5
Junction-to-board thermal resistance RθJB 22.2 °C/W 5
Quiescent current IQ 5 mA EN = High, no load, device switching, fsw = 1 MHz 5
Shutdown current ISD 0.3 70 µA EN = GND, TJ = -40°C to 125°C 5
Undervoltage lockout VUVLO 2.85 2.92 3 V VIN rising, TJ = -40°C to 125°C 5
Undervoltage lockout hysteresis VHYS 200 mV 5
Thermal shutdown threshold TJSD 170 °C TJ rising 5
Thermal shutdown hysteresis TJSD 20 °C TJ falling 5
High-level input-threshold voltage at EN/SYNC VH_EN 0.97 1.01 1.04 V 5
Low-level input-threshold voltage at EN/SYNC VL_EN 0.87 0.9 0.93 V 5
High-level input-threshold clock signal on EN/SYNC VH_SYNC 1.1 V EN/SYNC = clock 5
Low-level input-threshold clock signal on EN/SYNC VL_SYNC 0.4 V EN/SYNC = clock 5
Input leakage current into EN/SYNC IEN,LKG 5 160 nA EN/SYNC = GND or VIN, -40°C ≤ TJ ≤ 125°C 5
Pulldown resistor on EN/SYNC RPD 330 500 kΩ EN/SYNC = Low 5
Enable delay time tdelay 1 ms RS-CONF = 80.6 kΩ 5
NR/SS source current INR/SS 67.5 75 82.5 µA 5
S-CONF resistor step range accuracy RS-CONF -4 4 % RS-CONF tolerance for all settings 5
Power good threshold rising VPG 93 95 98 % VFB rising, referenced to VFB nominal 5
Power good threshold falling VPG 88 90 93 % VFB falling, referenced to VFB nominal 5
Low-level output voltage at PG pin VPG,OL 0.4 V ISINK = 1 mA 5
Input leakage current into PG pin IPG,LKG 5 500 nA VPG = 5 V; -40°C ≤ TJ ≤ 125°C 5
Power good delay time tPG,DLY 8 µs VFB falling 5
Minimum on-time ton 35 70 ns VIN ≥ 5 V, Iout = 1 A 6
Minimum off-time toff 50 60 ns VIN ≥ 5 V, Iout = 1 A 6
Feedback regulation accuracy VFB 0.792 0.8 0.812 V -40°C ≤ TJ ≤ 150°C 6
Feedback regulation accuracy VFB 0.792 0.8 0.808 V -40°C ≤ TJ ≤ 125°C 6
Input leakage current into FB IFB,LKG 1 70 nA VFB = 0.8 V, -40°C ≤ TJ ≤ 125°C 6
Input leakage current into VO IVO,LKG 0.01 30 µA VVO = 1.2 V, -40°C ≤ TJ ≤ 125°C 6
Power supply rejection ratio PSRR 65 dB VIN = 12 V, 1.2 VOUT, 1 A, fsw = 1 MHz, f ≤ 100 kHz 6
Power supply rejection ratio PSRR 70 dB VIN = 5 V, 1.2 VOUT, 1 A, fsw = 2.2 MHz, f ≤ 100 kHz 6
Output voltage RMS noise VNRMS 24.4 µVRMS VIN = 12 V, BW = 100 Hz to 100 kHz, VOUT = 1.2 V 6
Output voltage RMS noise VNRMS 13.5 µVRMS VIN = 5 V, BW = 100 Hz to 100 kHz, VOUT = 1.2 V 6
Output ripple voltage at fSW Vopp 9 µVRMS VIN = 12 V, fSW = 1 MHz, VOUT = 1.2 V, Lf = 10 nH 6
Output ripple voltage at fSW Vopp 2.2 µVRMS VIN = 5 V, fSW = 2.2 MHz, VOUT = 1.2 V, Lf = 10 nH 6
Output discharge resistance RDIS 7 Ω EN/SYNC = GND, VOUT = 1.2 V, VIN ≥ 5 V 6
Output discharge resistance RDIS 32 Ω EN/SYNC = GND, VOUT = 5 V, VIN ≥ 5 V 6
Switching frequency fSW 1.98 2.2 2.42 MHz 2.2-MHz setting 6
Synchronization range fSW 1.9 2.2 2.42 MHz 2.2-MHz setting 6
Switching frequency fSW 0.9 1 1.18 MHz 1-MHz setting 6
Synchronization range fSW 0.86 1 1.2 MHz 1-MHz setting 6
Synchronization duty cycle DSYNC 45 55 % 6
Synchronization phase delay tsync_elay 90 ns phase delay from EN/SYNC rising edge to SW rising edge 6
Peak switch current limit ISWpeak 3.7 4.3 5.1 A TPS62913 6
Negative valley current limit Inegvalley -1.39 -0.96 A 6
High-side FET on-resistance RDS(ON) 57 95 mΩ VIN ≥ 5 V 6
Low-side FET on-resistance RDS(ON) 20 39 mΩ VIN ≥ 5 V 6

Materials and finish

As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).

Part Material Colour / plating Datasheet says Page
contacts copper • Place the inductor close to the SW pin. Minimize the copper area at the switch node. 31

CAD (Adom-generated)

  • Symbol: TPS62913RPUR
  • Footprint: Adom_Gen:Texas_Instruments_TPS62913_927135
  • 3D model: generated to fit the land (STEP)
  • 3D model files: tps62913rpur-etched.step / tps62913rpur-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); tps62913rpur.step / tps62913rpur.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (41 pp, sha256 6b27cbc00d3de5f5, retrieved 2026-11-17, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: symbol generated from the datasheet pin table; footprint an Adom_Gen land derived from the manufacturer drawing; 3D model generated to fit that land.

Datasheet PDF