3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Contents
README
markdownTPS62913RPUR
Texas Instruments · DC-DC Converters · VQFN-10-HR(2x2)
TPS62913RPUR from Texas Instruments, in a VQFN-10-HR(2x2). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). The symbol is generated from that pin table, the footprint is an Adom_Gen land derived from the manufacturer drawing, and the 3D model is generated to fit it.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | EN/SYNC | input | Enable/disable pin with threshold comparator: logic low disables the device, pulling it high enables it, it has an internal pulldown of typically 500 kΩ when disabled, and applying a clock synchronizes the device. |
| 2 | SW | bidirectional | Switch pin of the power stage. |
| 3 | VO | input | Output voltage sense pin that needs to be connected directly after the first inductor. |
| 4 | PGND | power_in | Power ground connection. |
| 5 | PG | output | Open-drain power-good output that is pulled to GND when VOUT is below the power-good threshold, requires a pullup resistor for a logic high, and can be left open or tied to GND if not used. |
| 6 | VIN | power_in | Power supply input voltage pin. |
| 7 | PSNS | input | Power sense ground that must be connected directly to the ground plane. |
| 8 | NR/SS | output | A capacitor connected to this pin sets the soft-start time and the low-frequency noise level of the device. |
| 9 | FB | input | Feedback pin of the device. |
| 10 | S-CONF | output | Smart Configuration pin that configures the operation modes of the device, as described in Table 7-1. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | VQFN-10-HR(2x2) |
| Category | Power Management (PMIC) |
| Pins | 10 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Voltage VIN, EN/SYNC, PG, S-CONF | -0.3 | 18 | V | 4 | |||
| Voltage SW AC | -2.5 | 21 | V | less than 10 ns, while switching | 4 | ||
| Voltage VO, FB, NR/SS | -0.3 | 6 | V | 4 | |||
| Voltage PSNS | -0.3 | 0.3 | V | 4 | |||
| Sink current PG | 10 | mA | 4 | ||||
| Junction temperature | TJ | -40 | 150 | °C | 4 | ||
| Storage temperature | Tstg | -65 | 150 | °C | 4 | ||
| Input voltage | VIN | 3 | 17 | V | 4 | ||
| Output voltage | VOUT | 0.8 | 5.5 | V | 4 | ||
| Effective input capacitance | CIN | 5 | 10 | µF | 4 | ||
| Effective output inductance tolerance | L1 | -30 | 20 | % | nominal 2.2 / 4.7 µH | 4 | |
| Effective output capacitance | COUT | 40 | 47 | 80 | µF | 4 | |
| Effective filter inductance | Lf | 0 | 10 | 50 | nH | 4 | |
| Effective filter capacitance | Cf | 20 | 40 | 160 | µF | 4 | |
| Effective total output capacitance | COUT + Cf | 40 | 200 | µF | 4 | ||
| Output current | IOUT | 0 | 3 | A | for TPS62913 | 4 | |
| Junction temperature operating | TJ | -40 | 150 | °C | 4 | ||
| Junction-to-ambient thermal resistance | RθJA | 87.7 | °C/W | JEDEC 51-7 board | 5 | ||
| Junction-to-ambient thermal resistance | RθJA | 56.6 | °C/W | PCB TPS6291xEVM-077 | 5 | ||
| Junction-to-case (top) thermal resistance | RθJC(top) | 61.9 | °C/W | 5 | |||
| Junction-to-board thermal resistance | RθJB | 22.2 | °C/W | 5 | |||
| Quiescent current | IQ | 5 | mA | EN = High, no load, device switching, fsw = 1 MHz | 5 | ||
| Shutdown current | ISD | 0.3 | 70 | µA | EN = GND, TJ = -40°C to 125°C | 5 | |
| Undervoltage lockout | VUVLO | 2.85 | 2.92 | 3 | V | VIN rising, TJ = -40°C to 125°C | 5 |
| Undervoltage lockout hysteresis | VHYS | 200 | mV | 5 | |||
| Thermal shutdown threshold | TJSD | 170 | °C | TJ rising | 5 | ||
| Thermal shutdown hysteresis | TJSD | 20 | °C | TJ falling | 5 | ||
| High-level input-threshold voltage at EN/SYNC | VH_EN | 0.97 | 1.01 | 1.04 | V | 5 | |
| Low-level input-threshold voltage at EN/SYNC | VL_EN | 0.87 | 0.9 | 0.93 | V | 5 | |
| High-level input-threshold clock signal on EN/SYNC | VH_SYNC | 1.1 | V | EN/SYNC = clock | 5 | ||
| Low-level input-threshold clock signal on EN/SYNC | VL_SYNC | 0.4 | V | EN/SYNC = clock | 5 | ||
| Input leakage current into EN/SYNC | IEN,LKG | 5 | 160 | nA | EN/SYNC = GND or VIN, -40°C ≤ TJ ≤ 125°C | 5 | |
| Pulldown resistor on EN/SYNC | RPD | 330 | 500 | kΩ | EN/SYNC = Low | 5 | |
| Enable delay time | tdelay | 1 | ms | RS-CONF = 80.6 kΩ | 5 | ||
| NR/SS source current | INR/SS | 67.5 | 75 | 82.5 | µA | 5 | |
| S-CONF resistor step range accuracy | RS-CONF | -4 | 4 | % | RS-CONF tolerance for all settings | 5 | |
| Power good threshold rising | VPG | 93 | 95 | 98 | % | VFB rising, referenced to VFB nominal | 5 |
| Power good threshold falling | VPG | 88 | 90 | 93 | % | VFB falling, referenced to VFB nominal | 5 |
| Low-level output voltage at PG pin | VPG,OL | 0.4 | V | ISINK = 1 mA | 5 | ||
| Input leakage current into PG pin | IPG,LKG | 5 | 500 | nA | VPG = 5 V; -40°C ≤ TJ ≤ 125°C | 5 | |
| Power good delay time | tPG,DLY | 8 | µs | VFB falling | 5 | ||
| Minimum on-time | ton | 35 | 70 | ns | VIN ≥ 5 V, Iout = 1 A | 6 | |
| Minimum off-time | toff | 50 | 60 | ns | VIN ≥ 5 V, Iout = 1 A | 6 | |
| Feedback regulation accuracy | VFB | 0.792 | 0.8 | 0.812 | V | -40°C ≤ TJ ≤ 150°C | 6 |
| Feedback regulation accuracy | VFB | 0.792 | 0.8 | 0.808 | V | -40°C ≤ TJ ≤ 125°C | 6 |
| Input leakage current into FB | IFB,LKG | 1 | 70 | nA | VFB = 0.8 V, -40°C ≤ TJ ≤ 125°C | 6 | |
| Input leakage current into VO | IVO,LKG | 0.01 | 30 | µA | VVO = 1.2 V, -40°C ≤ TJ ≤ 125°C | 6 | |
| Power supply rejection ratio | PSRR | 65 | dB | VIN = 12 V, 1.2 VOUT, 1 A, fsw = 1 MHz, f ≤ 100 kHz | 6 | ||
| Power supply rejection ratio | PSRR | 70 | dB | VIN = 5 V, 1.2 VOUT, 1 A, fsw = 2.2 MHz, f ≤ 100 kHz | 6 | ||
| Output voltage RMS noise | VNRMS | 24.4 | µVRMS | VIN = 12 V, BW = 100 Hz to 100 kHz, VOUT = 1.2 V | 6 | ||
| Output voltage RMS noise | VNRMS | 13.5 | µVRMS | VIN = 5 V, BW = 100 Hz to 100 kHz, VOUT = 1.2 V | 6 | ||
| Output ripple voltage at fSW | Vopp | 9 | µVRMS | VIN = 12 V, fSW = 1 MHz, VOUT = 1.2 V, Lf = 10 nH | 6 | ||
| Output ripple voltage at fSW | Vopp | 2.2 | µVRMS | VIN = 5 V, fSW = 2.2 MHz, VOUT = 1.2 V, Lf = 10 nH | 6 | ||
| Output discharge resistance | RDIS | 7 | Ω | EN/SYNC = GND, VOUT = 1.2 V, VIN ≥ 5 V | 6 | ||
| Output discharge resistance | RDIS | 32 | Ω | EN/SYNC = GND, VOUT = 5 V, VIN ≥ 5 V | 6 | ||
| Switching frequency | fSW | 1.98 | 2.2 | 2.42 | MHz | 2.2-MHz setting | 6 |
| Synchronization range | fSW | 1.9 | 2.2 | 2.42 | MHz | 2.2-MHz setting | 6 |
| Switching frequency | fSW | 0.9 | 1 | 1.18 | MHz | 1-MHz setting | 6 |
| Synchronization range | fSW | 0.86 | 1 | 1.2 | MHz | 1-MHz setting | 6 |
| Synchronization duty cycle | DSYNC | 45 | 55 | % | 6 | ||
| Synchronization phase delay | tsync_elay | 90 | ns | phase delay from EN/SYNC rising edge to SW rising edge | 6 | ||
| Peak switch current limit | ISWpeak | 3.7 | 4.3 | 5.1 | A | TPS62913 | 6 |
| Negative valley current limit | Inegvalley | -1.39 | -0.96 | A | 6 | ||
| High-side FET on-resistance | RDS(ON) | 57 | 95 | mΩ | VIN ≥ 5 V | 6 | |
| Low-side FET on-resistance | RDS(ON) | 20 | 39 | mΩ | VIN ≥ 5 V | 6 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | copper | • Place the inductor close to the SW pin. Minimize the copper area at the switch node. | 31 |
CAD (Adom-generated)
- Symbol:
TPS62913RPUR - Footprint:
Adom_Gen:Texas_Instruments_TPS62913_927135 - 3D model: generated to fit the land (STEP)
- 3D model files:
tps62913rpur-etched.step/tps62913rpur-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);tps62913rpur.step/tps62913rpur.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (41 pp, sha256
6b27cbc00d3de5f5, retrieved 2026-11-17, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: symbol generated from the datasheet pin table; footprint an Adom_Gen land derived from the manufacturer drawing; 3D model generated to fit that land.