component
TPS62091RGTR
Public Made by Adomby adom
Texas Instruments DC-DC Converters, QFN-16-EP(3x3). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads on click. Unloads only if this page sits in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads on click. Unloads only if this page sits in the background.
PCB Footprint
Open full view ↗Loads on click. Unloads only if this page sits in the background.
Datasheet
Open in new tab ↗Loads on click. Unloads only if this page sits in the background.
README
markdownTPS62091RGTR
Texas Instruments · DC-DC Converters · QFN-16-EP(3x3)
TPS62091RGTR from Texas Instruments, in a QFN-16-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SW | bidirectional | Switch node of the power stage connecting high-side MOSFET, inductor, and low-side MOSFET; voltage range -0.3 V to VIN + 0.3 V. |
| 2 | SW | bidirectional | Switch node of the power stage connecting high-side MOSFET, inductor, and low-side MOSFET; voltage range -0.3 V to VIN + 0.3 V. |
| 3 | FREQ | input | Frequency selection input; GND selects 2.8 MHz, VIN selects 1.4 MHz switching frequency; has internal 400 kΩ pull-down, floating defaults to 2.8 MHz. |
| 4 | PG | tri_state | Power good open-drain output; high impedance when output within regulation, pulled low when below nominal value; maximum sink current 1 mA. |
| 5 | FB | input | Feedback input pin for output voltage regulation; connect resistor divider to set output voltage in adjustable versions; fixed versions have 400 kΩ pull-down when EN is low. |
| 6 | AGND | power_in | Analog ground reference for control circuitry and feedback signals; connected to exposed thermal pad. |
| 7 | CP | bidirectional | Charge pump flying capacitor; connect 10 nF capacitor between CP and CN to complete gate driver charge pump; voltage range -0.3 V to VIN + 7.0 V. |
| 8 | CN | bidirectional | Charge pump flying capacitor; connect 10 nF capacitor between CP and CN to complete gate driver charge pump; voltage range -0.3 V to VIN + 7.0 V. |
| 9 | SS | input | Softstart ramp control pin; external capacitor sets startup ramp time with 7.5 µA charge current; floating pin sets minimum startup time around 50 µs. |
| 10 | AVIN | power_in | Bias supply input voltage pin for IC control circuitry; operating range 2.5 V to 6 V; voltage limits -0.3 V to 7 V. |
| 11 | PVIN | power_in | Primary power supply input voltage pin; operating range 2.5 V to 6 V; requires 10 µF or larger input capacitor; voltage limits -0.3 V to 7 V. |
| 12 | PVIN | power_in | Primary power supply input voltage pin; operating range 2.5 V to 6 V; requires 10 µF or larger input capacitor; voltage limits -0.3 V to 7 V. |
| 13 | EN | input | Device enable input; pull high to enable converter, pull low to disable; has internal 400 kΩ pull-down resistor; shutdown current 0.6 µA typical. |
| 14 | PGND | power_in | Power ground return path for output stage; must be soldered to exposed thermal pad for mechanical reliability and thermal dissipation. |
| 15 | PGND | power_in | Power ground return path for output stage; must be soldered to exposed thermal pad for mechanical reliability and thermal dissipation. |
| 16 | VOS | input | Output voltage sense pin; connects directly to converter output for feedback regulation; noise-sensitive requiring short direct routing; voltage limits -0.3 V to 7 V. |
| 17 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | QFN-16-EP(3x3) |
| Category | Power Management (PMIC) |
| Pins | 17 |
CAD (KiCad official)
- Symbol:
TPS62091RGTR - Footprint:
Package_DFN_QFN:QFN-16-1EP_3x3mm_P0.5mm_EP1.7x1.7mm - 3D model: QFN-16-EP(3x3) (KiCad packages3D, STEP)
- 3D model files:
tps62091rgtr-etched.step/tps62091rgtr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);tps62091rgtr.step/tps62091rgtr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (32 pp, sha256
1aca00440b3d4033, retrieved 2026-09-27, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.2, primaryclaude-haiku-4-5-20251001(text), consensusclaude-sonnet-4-6(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).