Generated by kicad-footprint-generator · KiCad file format 20260206
TPS613785QWRTERQ1
Texas Instruments · DC-DC Converters · WQFN-16(3x3)
TPS613785QWRTERQ1 from Texas Instruments, in a WQFN-16(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VIN | power_in | IC power supply input, operating range 2.3V to 14V with UVLO threshold at 2.04V rising, 2.2V falling. |
| 2 | BST | power_in | Bootstrap supply for high-side N-MOSFET gate driver, requires 0.1µF to 1µF ceramic capacitor between BST and SW. |
| 3 | SW | passive | Switching node pin connected to drain of low-side FET and source of high-side FET. |
| 4 | SW | passive | Switching node pin connected to drain of low-side FET and source of high-side FET. |
| 5 | MODE/SYNC | input | Mode selection and clock synchronization input; logic high selects forced PWM mode, low or floating selects auto PFM mode. |
| 6 | VCC | power_in | Regulated 4.8V output of internal LDO regulator, requires 1µF minimum ceramic capacitor to GND. |
| 7 | GND | power_in | Power ground and reference of the IC, connected to source of low-side FET. |
| 8 | GND | power_in | Power ground and reference of the IC, connected to source of low-side FET. |
| 9 | VO | output | Output of isolation FET, connect load to this pin to achieve input/output isolation. |
| 10 | OUT | output | Output of high-side FET drain, connect this pin to disable load disconnect protection or short to VO pin. |
| 11 | PG | output | Power good indicator with open-drain output, goes high 3.4ms after VOUT reaches 90% of target voltage. |
| 12 | ILIM | input | Current limit setting pin, connect resistor to GND to program peak current limit from 1A to 4.8A. |
| 13 | FB | input | Feedback pin for output voltage regulation via resistor divider, reference voltage 0.8V nominal. |
| 14 | COMP | input | Compensation network connection point for error amplifier output, external RC network optimizes loop stability. |
| 15 | EN | input | Enable logic input, high (>1.2V) enables converter operation, low (<0.4V) disables with 0.5µA shutdown current. |
| 16 | FREQ | input | Frequency setting pin, connect resistor to GND to program switching frequency from 200kHz to 2.2MHz. |
| 17 | Thermal Pad | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | WQFN-16(3x3) |
| Category | Power Management (PMIC) |
| Pins | 17 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Voltage range at terminals VIN | VIN | -0.3 | 16 | V | Voltages referenced to network ground | 5 | |
| Voltage range at terminals VO, SW, OUT | VO, SW, OUT | -0.3 | 23 | V | Voltages referenced to network ground | 5 | |
| Voltage range at terminal BST | BST | -0.3 | V | 5 | |||
| Voltage range at terminals MODE/SYNC, FB, FREQ, ILIM, VCC, COMP, EN | MODE/SYNC, FB, FREQ, ILIM, VCC, COMP, EN | -0.3 | 6 | V | Voltages referenced to network ground | 5 | |
| Voltage range at terminal PG | PG | -0.3 | 20 | V | Voltages referenced to network ground | 5 | |
| Operating junction temperature | TJ | -40 | 150 | °C | 5 | ||
| Storage temperature | Tstg | -65 | 150 | °C | 5 | ||
| Input voltage | VIN | 2.3 | 14 | V | 5 | ||
| Output voltage | VOUT | 4 | 18.5 | V | 5 | ||
| Operating junction temperature | TJ | -40 | 150 | °C | 5 | ||
| VIN input voltage range | VIN | 2.3 | 14 | V | 6 | ||
| VIN under voltage lockout threshold | VIN_UVLO | 2.2 | 2.3 | V | VIN rising | 6 | |
| VIN under voltage lockout threshold | VIN_UVLO | 2.04 | 2.2 | V | VIN falling | 6 | |
| Output over-voltage protection threshold | VOVP | 19.3 | 20 | 20.5 | V | VIN = 3.3 V, VOUT rising | 6 |
| Reference voltage at FB pin | VREF | 0.788 | 0.8 | 0.812 | V | TJ = -40 to 125°C, RFB = 16.0kΩ | 6 |
| Output voltage 9V (TPS613785Q1) | VOUT_9V | 8.75 | 9 | 9.15 | V | TJ = -40 to 125°C, RFB = 2.0 kΩ | 6 |
| Output voltage 10V (TPS613785Q1) | VOUT_10V | 9.75 | 10 | 10.2 | V | TJ = -40 to 125°C, RFB = 4.0 kΩ | 6 |
| Output voltage 11V (TPS613785Q1) | VOUT_11V | 10.7 | 11 | 11.2 | V | TJ = -40 to 125°C, RFB = 8.0 kΩ | 6 |
| Output voltage 12V (TPS613785Q1) | VOUT_12V | 11.7 | 12 | 12.22 | V | TJ = -40 to 125°C, RFB = 16.0 kΩ | 6 |
| Quiescent current into VIN pin | IQ | 25 | 35 | µA | IC enabled, no load, VIN = 3.3 V, VOUT = 18.5 V, VFB = VREF + 0.1 V | 6 | |
| Quiescent current into OUT pin | IQ | 10 | 20 | µA | IC enabled, no load, VIN = 3.3 V, VOUT = 18.5 V, VFB = VREF + 0.1 V | 6 | |
| Shutdown current into VIN pin | ISD | 0.6 | 5 | µA | IC disabled, VIN =14 V, EN = GND | 6 | |
| Leakage current into SW | ISW_LKG | 5 | µA | IC disabled, VIN = OUT = SW =14 V | 6 | ||
| Reverse leakage current into VO | IVO_LKG | 5 | µA | IC disabled, OUT= VO = 5 V, SW = 0 | 6 | ||
| Leakage current into FB pin | IFB_LKG | 50 | nA | 6 | |||
| Peak switching current limit (FPWM) | ILIM_SW | 4 | 4.8 | 5.55 | A | FPWM, RLIM = 20 kΩ, Duty cycle = 65% | 7 |
| Peak switching current limit (Auto PFM) | ILIM_SW | 4 | 4.8 | 5.55 | A | Auto PFM, RLIM = 20 kΩ, Duty cycle = 65% | 7 |
| Peak switching current limit at softstart | ILIM_SS_1 | 0.9 | 1.15 | 1.4 | A | VIN = 3.3 V, VOUT = 0 V, RLIM = 20 kΩ | 7 |
| Switching frequency | Fsw | 2050 | 2200 | 2400 | kHz | RFREQ = 18 kΩ | 7 |
| Switching frequency | Fsw | 180 | 200 | 230 | kHz | RFREQ = 218 kΩ | 7 |
| PG delay time | tPG_DELAY | 2.5 | 3.4 | 4.3 | ms | 7 | |
| Synchronization frequency minimum | fSYNC_MIN | 200 | kHz | 7 | |||
| Synchronization frequency maximum | fSYNC_MAX | 2200 | kHz | 7 | |||
| EN, MODE/SYNC pins logic high threshold | VIH | 1.2 | V | 7 | |||
| EN, MODE/SYNC pins logic low threshold | VIL | 0.4 | V | 7 | |||
| VIN hysteresis (UVLO) | VIN_HYS | 160 | mV | 6 | |||
| VCC regulation | VCC | 4.8 | V | IVCC = 6 mA, VOUT = 9V | 6 | ||
| Output over-voltage protection hysteresis | VOVP_HYS | 0.5 | V | VIN = 3.3 V, OVP threshold | 6 | ||
| Low-side MOSFET on resistance | RDS(on) | 50 | mΩ | VCC = 4.85 V | 6 | ||
| High-side MOSFET on resistance | RDS(on) | 50 | mΩ | VCC = 4.85 V | 6 | ||
| Isolation MOSFET on resistance | RDS(on) | 100 | mΩ | VCC = 4.85 V | 6 | ||
| Peak switching current limit (FPWM, 4.7 µH) | ILIM_SW | 0.75 | A | FPWM, RLIM = 102 kΩ, Duty cycle = 65%, 4.7uH | 7 | ||
| Peak switching current limit (Auto PFM, 4.7 µH) | ILIM_SW | 0.75 | A | Auto PFM, RLIM = 102 kΩ, Duty cycle = 65%, 4.7uH | 7 | ||
| Maximum duty cycle | Dmax | 78 | % | RFREQ = 18 kΩ | 7 | ||
| Minimal on time | tON_min | 70 | ns | 7 | |||
| COMP pin sink current | ISINK | 6 | µA | VFB = VREF + 0.2V | 7 | ||
| COMP pin source current | ISOURCE | 6 | µA | VFB = VREF - 0.2V | 7 | ||
| COMP pin high clamp voltage | VCCLPH | 1.3 | V | VFB = VREF - 0.2V, ILIM = 4.8 A | 7 | ||
| COMP pin high low voltage | VCCLPL | 0.6 | V | VFB = VREF + 0.2V | 7 | ||
| Error amplifier transconductance | GmEA | 70 | µS | VCOMP = 1.0 V | 7 | ||
| PG threshold for rising FB voltage | VPG_TH | 90 | % | Reference to VREF | 7 | ||
| PG hysteresis | VPG_HYS | 5 | % | Reference to VREF | 7 | ||
| PG pin sink current capability | IPG_SINK | 20 | mA | VPG = 0.4 V | 7 | ||
| Delay time between EN high and device working | tEN_DELAY | 0.4 | ms | 7 | |||
| Softstart time | tSS | 2.5 | ms | 7 | |||
| EN, MODE/SYNC pins internal pull down resistor | RDOWN | 800 | kΩ | 7 | |||
| Thermal shutdown rising threshold | tSD_R | 165 | °C | TJ rising | 7 | ||
| Thermal shutdown falling threshold | tSD_F | 145 | °C | TJ falling | 7 | ||
| Junction-to-ambient thermal resistance | RθJA | 46.2 | °C/W | 5 | |||
| Junction-to-case (bottom) thermal resistance | RθJC(bot) | 8.8 | °C/W | 6 |
CAD (KiCad official)
- Symbol:
TPS613785QWRTERQ1 - Footprint:
Package_DFN_QFN:QFN-16-1EP_3x3mm_P0.5mm_EP1.7x1.7mm - 3D model: WQFN-16(3x3) (KiCad packages3D, STEP)
- 3D model files:
tps613785qwrterq1-etched.step/tps613785qwrterq1-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);tps613785qwrterq1.step/tps613785qwrterq1.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (42 pp, sha256
3799e162e33f3792, retrieved 2026-09-24, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.2, primaryclaude-haiku-4-5-20251001(text), consensusclaude-sonnet-4-6(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).