← Commit history

Initial commit: component/tps613785qwrterq1

Ray ·43022f6be2 ·
2 files changed +267
README.mdadded+54
@@ -0,0 +1,54 @@+# TPS613785QWRTERQ1++**Texas Instruments** · DC-DC Converters · WQFN-16(3x3)++TPS613785QWRTERQ1 from Texas Instruments, in a WQFN-16(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | VIN | power_in | IC power supply input, operating range 2.3V to 14V with UVLO threshold at 2.04V rising, 2.2V falling. |+| 2 | BST | power_in | Bootstrap supply for high-side N-MOSFET gate driver, requires 0.1µF to 1µF ceramic capacitor between BST and SW. |+| 3 | SW | passive | Switching node pin connected to drain of low-side FET and source of high-side FET. |+| 4 | SW | passive | Switching node pin connected to drain of low-side FET and source of high-side FET. |+| 5 | MODE/SYNC | input | Mode selection and clock synchronization input; logic high selects forced PWM mode, low or floating selects auto PFM mode. |+| 6 | VCC | power_in | Regulated 4.8V output of internal LDO regulator, requires 1µF minimum ceramic capacitor to GND. |+| 7 | GND | power_in | Power ground and reference of the IC, connected to source of low-side FET. |+| 8 | GND | power_in | Power ground and reference of the IC, connected to source of low-side FET. |+| 9 | VO | output | Output of isolation FET, connect load to this pin to achieve input/output isolation. |+| 10 | OUT | output | Output of high-side FET drain, connect this pin to disable load disconnect protection or short to VO pin. |+| 11 | PG | output | Power good indicator with open-drain output, goes high 3.4ms after VOUT reaches 90% of target voltage. |+| 12 | ILIM | input | Current limit setting pin, connect resistor to GND to program peak current limit from 1A to 4.8A. |+| 13 | FB | input | Feedback pin for output voltage regulation via resistor divider, reference voltage 0.8V nominal. |+| 14 | COMP | input | Compensation network connection point for error amplifier output, external RC network optimizes loop stability. |+| 15 | EN | input | Enable logic input, high (>1.2V) enables converter operation, low (<0.4V) disables with 0.5µA shutdown current. |+| 16 | FREQ | input | Frequency setting pin, connect resistor to GND to program switching frequency from 200kHz to 2.2MHz. |+| 17 | Thermal Pad | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Texas Instruments |+| Package | WQFN-16(3x3) |+| Category | Power Management (PMIC) |+| Pins | 17 |++## CAD (KiCad official)++- Symbol: `TPS613785QWRTERQ1`+- Footprint: `Package_DFN_QFN:QFN-16-1EP_3x3mm_P0.5mm_EP1.7x1.7mm`+- 3D model: WQFN-16(3x3) (KiCad packages3D, STEP)+- 3D model files: `tps613785qwrterq1-etched.step` / `tps613785qwrterq1-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `tps613785qwrterq1.step` / `tps613785qwrterq1.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/tps61378-q1) (42 pp, sha256 `3799e162e33f3792`, retrieved 2026-09-24, tier: lcsc)+- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.2`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-4-6` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/tps613785qwrterq1-datasheet.pdf)
page.jsonadded+213
@@ -0,0 +1,213 @@+{+  "slug": "tps613785qwrterq1",+  "version": "0.1.0",+  "type": "component",+  "description": "Texas Instruments DC-DC Converters, WQFN-16(3x3). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",+  "tags": [+    "component",+    "power management (pmic)",+    "tps613785qwrterq1",+    "factory-2.0.0",+    "extractor-text"+  ],+  "dependencies": {},+  "hero": {+    "type": "image",+    "path": "docs/hero.png"+  },+  "files": [+    "page.json",+    "README.md",+    "tps613785qwrterq1.kicad_sym",+    "tps613785qwrterq1.kicad_mod",+    "tps613785qwrterq1.glb",+    "tps613785qwrterq1.step",+    "tps613785qwrterq1.lbr",+    "docs/hero.png",+    "docs/tps613785qwrterq1-datasheet.pdf",+    "viewers/symbol.html",+    "viewers/footprint.html"+  ],+  "component": {+    "mpn": "TPS613785QWRTERQ1",+    "manufacturer": "Texas Instruments",+    "package": "WQFN-16(3x3)",+    "pin_count": 17,+    "category": "Power Management (PMIC)",+    "subcategory": "DC-DC Converters",+    "datasheet": "https://www.ti.com/cn/lit/gpn/tps61378-q1",+    "parts": {+      "symbol": "tps613785qwrterq1.kicad_sym",+      "footprint": "tps613785qwrterq1.kicad_mod",+      "model_3d": "tps613785qwrterq1-etched.glb",+      "model_3d_plain": "tps613785qwrterq1.glb",+      "model_3d_step": "tps613785qwrterq1-etched.step",+      "model_3d_step_plain": "tps613785qwrterq1.step",+      "lbr": "tps613785qwrterq1.lbr"+    },+    "distributor_links": {+      "lcsc": "C3188435",+      "digikey": "296-TPS613785QWRTERQ1TR-ND",+      "mouser": "595-PS613785QWRTERQ1"+    },+    "distributor_check": {+      "checked_at": "2026-09-24T19:01:18Z",+      "source": "Component Ocean /api/assign-pns",+      "digikey": {+        "pn": "296-TPS613785QWRTERQ1TR-ND",+        "status": "found",+        "lifecycle": "Active"+      },+      "mouser": {+        "pn": "595-PS613785QWRTERQ1",+        "status": "found"+      }+    },+    "pins": [+      {+        "number": "1",+        "name": "VIN",+        "type": "power_in",+        "description": "IC power supply input, operating range 2.3V to 14V with UVLO threshold at 2.04V rising, 2.2V falling."+      },+      {+        "number": "2",+        "name": "BST",+        "type": "power_in",+        "description": "Bootstrap supply for high-side N-MOSFET gate driver, requires 0.1µF to 1µF ceramic capacitor between BST and SW."+      },+      {+        "number": "3",+        "name": "SW",+        "type": "passive",+        "description": "Switching node pin connected to drain of low-side FET and source of high-side FET."+      },+      {+        "number": "4",+        "name": "SW",+        "type": "passive",+        "description": "Switching node pin connected to drain of low-side FET and source of high-side FET."+      },+      {+        "number": "5",+        "name": "MODE/SYNC",+        "type": "input",+        "description": "Mode selection and clock synchronization input; logic high selects forced PWM mode, low or floating selects auto PFM mode."+      },+      {+        "number": "6",+        "name": "VCC",+        "type": "power_in",+        "description": "Regulated 4.8V output of internal LDO regulator, requires 1µF minimum ceramic capacitor to GND."+      },+      {+        "number": "7",+        "name": "GND",+        "type": "power_in",+        "description": "Power ground and reference of the IC, connected to source of low-side FET."+      },+      {+        "number": "8",+        "name": "GND",+        "type": "power_in",+        "description": "Power ground and reference of the IC, connected to source of low-side FET."+      },+      {+        "number": "9",+        "name": "VO",+        "type": "output",+        "description": "Output of isolation FET, connect load to this pin to achieve input/output isolation."+      },+      {+        "number": "10",+        "name": "OUT",+        "type": "output",+        "description": "Output of high-side FET drain, connect this pin to disable load disconnect protection or short to VO pin."+      },+      {+        "number": "11",+        "name": "PG",+        "type": "output",+        "description": "Power good indicator with open-drain output, goes high 3.4ms after VOUT reaches 90% of target voltage."+      },+      {+        "number": "12",+        "name": "ILIM",+        "type": "input",+        "description": "Current limit setting pin, connect resistor to GND to program peak current limit from 1A to 4.8A."+      },+      {+        "number": "13",+        "name": "FB",+        "type": "input",+        "description": "Feedback pin for output voltage regulation via resistor divider, reference voltage 0.8V nominal."+      },+      {+        "number": "14",+        "name": "COMP",+        "type": "input",+        "description": "Compensation network connection point for error amplifier output, external RC network optimizes loop stability."+      },+      {+        "number": "15",+        "name": "EN",+        "type": "input",+        "description": "Enable logic input, high (>1.2V) enables converter operation, low (<0.4V) disables with 0.5µA shutdown current."+      },+      {+        "number": "16",+        "name": "FREQ",+        "type": "input",+        "description": "Frequency setting pin, connect resistor to GND to program switching frequency from 200kHz to 2.2MHz."+      },+      {+        "number": "17",+        "name": "Thermal Pad",+        "type": "passive",+        "description": "Exposed pad (from the footprint; not named in the datasheet pin table)."+      }+    ],+    "provenance": {+      "extractor": "extract_pins 0.2",+      "factory_chain": {+        "factory": "2.0.0",+        "extractor": "extract_pins 0.2",+        "primary_model": "claude-haiku-4-5-20251001",+        "primary_mode": "text",+        "consensus_model": "claude-sonnet-4-6",+        "consensus": "agreed",+        "guards": "pin_guards 0.1: passed",+        "guard_notes": [+          "extractor flagged: Thermal pad (shown as position 17 in package layout diagrams) must be soldered to power ground plane",+          "exposed pad 17 added from the footprint"+        ],+        "pages_sent": 42,+        "cost_usd": 0.4304,+        "at": "2026-09-24T19:00:59"+      },+      "datasheet": {+        "url": "https://www.ti.com/cn/lit/gpn/tps61378-q1",+        "pages": 42,+        "sha256": "3799e162e33f3792",+        "source_tier": "lcsc"+      },+      "cad": "KiCad official (CC-BY-SA 4.0)",+      "pins": {+        "total": 17,+        "described": 17,+        "cites_pages": true,+        "refuses_to_fabricate": true+      }+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }+  },+  "visibility": "public",+  "org": "adom",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  }+}\ No newline at end of file