3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownTPS61170DRVT
Texas Instruments · DC-DC Converters · WSON-6-EP(2x2)
TPS61170DRVT from Texas Instruments, in a WSON-6-EP(2x2). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | FB | input | Feedback pin for current; connect to center tap of resistor divider to program output voltage. |
| 2 | COMP | output | Output of transconductance error amplifier; connect external RC network for regulator compensation. |
| 3 | GND | power_in | Ground reference. |
| 4 | SW | output | Switching node of the IC; connect to switched side of inductor. |
| 5 | CTRL | input | Multifunctional control pin to enable device and control feedback voltage with PWM signal or digital communications. |
| 6 | VIN | power_in | Input supply pin for the IC; accept supply voltage from 3 V to 18 V. |
| 7 | Thermal Pad | power_in | Thermal pad for heat dissipation; solder to analog ground plane to avoid thermal issue. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | WSON-6-EP(2x2) |
| Category | Power Management (PMIC) |
| Pins | 7 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage on VIN | VI | -0.3 | 20 | V | 3 | ||
| Voltage on CTRL | VI | -0.3 | 20 | V | 3 | ||
| Voltage on FB and COMP | VI | -0.3 | 3 | V | 3 | ||
| Voltage on SW | VI | -0.3 | 40 | V | 3 | ||
| Operating junction temperature | TJ | -40 | 150 | °C | 3 | ||
| Storage temperature | Tstg | -65 | 150 | °C | 3 | ||
| Input voltage range | VI | 3 | 18 | V | 4 | ||
| Output voltage range | VO | 38 | V | 4 | |||
| Inductor | L | 10 | 22 | μH | 4 | ||
| Output capacitor | CO | 1 | 10 | μF | 4 | ||
| Operating ambient temperature | TA | -40 | 85 | °C | 4 | ||
| Operating junction temperature | TJ | -40 | 125 | °C | 4 | ||
| Input voltage range, VIN | VI | 3 | 18 | V | 5 | ||
| Under-voltage lockout threshold | UVLO | 2.2 | 2.5 | V | VIN falling | 5 | |
| CTRL pulldown resistor | R(CTRL) | 400 | 800 | 1600 | kΩ | 5 | |
| Voltage feedback regulation voltage | VREF | 1.204 | 1.229 | 1.254 | V | 5 | |
| Voltage feedback regulation voltage under reprogram | V(REF_PWM) | 477 | 492 | 507 | mV | VFB = 492 mV | 5 |
| Oscillator frequency | fS | 1 | 1.2 | 1.5 | MHz | 5 | |
| Maximum duty cycle | Dmax | 90 | 93 | % | VFB = 100 mV | 5 | |
| Error amplifier transconductance | Gea | 240 | 320 | 400 | μmho | 5 | |
| N-channel MOSFET current limit | ILIM | 0.96 | 1.2 | 1.44 | A | D = Dmax | 5 |
| N-channel MOSFET on-resistance | RDS(on) | 0.3 | 0.6 | Ω | VIN = 3.6 V | 5 | |
| Start-up N-channel MOSFET on-resistance (VIN = 3.0 V) | RDS(on) | 0.7 | Ω | VIN = 3.0 V | 5 | ||
| EasyScale end time of program stream | tEOS | 2 | 360 | μs | 6 | ||
| EasyScale high time low bit (Logic 0) | tH_LB | 2 | 180 | μs | Logic 0 | 6 | |
| EasyScale low time low bit (Logic 0) | tL_LB | 360 | μs | Logic 0 | 6 | ||
| EasyScale high time high bit (Logic 1) | tH_HB | 360 | μs | Logic 1 | 6 | ||
| EasyScale low time high bit (Logic 1) | tL_HB | 2 | 180 | μs | Logic 1 | 6 | |
| Acknowledge output voltage low | VACKNL | 0.4 | V | Open drain, Rpullup =15 kΩ to Vin | 6 | ||
| Input capacitor | CI | 1 | μF | 4 | |||
| Junction-to-ambient thermal resistance | RθJA | 66.5 | °C/W | 4 | |||
| Junction-to-case (top) thermal resistance | RθJC(top) | 85.6 | °C/W | 4 | |||
| Junction-to-board thermal resistance | RθJB | 36 | °C/W | 4 | |||
| Junction-to-case (bottom) thermal resistance | RθJC(bot) | 7.1 | °C/W | 4 | |||
| Operating quiescent current into VIN | IQ | 2.3 | mA | Device PWM switching no load | 5 | ||
| Shutdown current | ISD | 1 | μA | CRTL=GND, VIN = 4.2 V | 5 | ||
| Under-voltage lockout hysteresis | Vhys | 70 | mV | 5 | |||
| CTRL logic high voltage | V(CTRLh) | 1.2 | V | VIN = 3 V to 18 V | 5 | ||
| CTRL logic low voltage | V(CTRL) | 0.4 | V | VIN = 3 V to 18 V | 5 | ||
| CTRL pulse width to shutdown | toff | 2.5 | ms | CTRL high to low | 5 | ||
| EasyScale detection time | tes_det | 260 | μs | CTRL pin low | 5 | ||
| EasyScale detection delay | tes_delay | 100 | μs | 5 | |||
| EasyScale detection window time | tes_win | 1 | ms | 5 | |||
| Voltage feedback input bias current | IFB | 200 | nA | VFB = 1.229 V | 5 | ||
| Minimum on pulse width | tmin_on | 40 | ns | 5 | |||
| COMP pin sink current | Isink | 100 | μA | 5 | |||
| COMP pin source current | Isource | 100 | μA | 5 | |||
| Error amplifier output resistance | Rea | 6 | MΩ | 5 pF connected to COMP | 5 | ||
| Error amplifier crossover frequency | fea | 500 | kHz | 5 pF connected to COMP | 5 | ||
| N-channel leakage current | ILN_NFET | 1 | μA | VSW = 35 V, TA = 25°C | 5 | ||
| Start-up current limit | ILIM_Start | 0.7 | A | D = Dmax | 5 | ||
| Time step for half current limit | tHalf_LIM | 5 | ms | 5 | |||
| Vref filter time constant | tREF | 180 | μs | 5 | |||
| VREF ramp up time | tstep | 213 | μs | 5 | |||
| EasyScale start time of program stream | tstart | 2 | μs | 6 | |||
| Acknowledge valid time | tvalACKN | 2 | μs | See (2) | 6 | ||
| Duration of acknowledge condition | tACKN | 512 | μs | See (2) | 6 | ||
| Thermal shutdown threshold | Tshutdown | 160 | °C | 6 | |||
| Thermal shutdown threshold hysteresis | Thysteresis | 15 | °C | 6 |
CAD (KiCad official)
- Symbol:
TPS61170DRVT - Footprint:
Package_SON:WSON-6-1EP_2x2mm_P0.65mm_EP1x1.6mm - 3D model: WSON-6-EP(2x2) (KiCad packages3D, STEP)
- 3D model files:
tps61170drvt-etched.step/tps61170drvt-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);tps61170drvt.step/tps61170drvt.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (37 pp, sha256
4d515bb23faa692e, retrieved 2026-09-24, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.2, primaryclaude-haiku-4-5-20251001(text), consensusclaude-sonnet-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).