main
History Download
Ray Publish 0.1.0 0b08a8e

TPS562201DDCR

Texas Instruments · DC-DC Converters · TSOT-23-6

TPS562201DDCR from Texas Instruments, in a TSOT-23-6. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 GND power_in Ground pin is the source terminal of the low-side power NFET and the ground terminal for the controller circuit, and sensitive VFB must connect to this GND at a single point.
2 SW output Switch node connection between the high-side NFET and the low-side NFET.
3 VIN power_in Input voltage supply pin, which is the drain terminal of the high-side power NFET and operates from 4.5 V to 17 V.
4 VFB input Converter feedback input that connects to the output voltage through a feedback resistor divider.
5 EN input Enable input control that is active high and must be pulled up to enable the device.
6 VBST power_in Supply input for the high-side NFET gate drive circuit, which requires a 0.1-µF capacitor connected between VBST and SW.

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package TSOT-23-6
Category Power Management (PMIC)
Pins 6

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Input voltage VIN, EN VIN, EN -0.3 19 V 4
Input voltage VBST VBST -0.3 25 V 4
Input voltage VBST (10-ns transient) VBST -0.3 27 V 10-ns transient 4
Input voltage VBST (vs SW) VBST (vs SW) -0.3 6 V 4
Input voltage VFB VFB -0.3 6 V 4
Input voltage SW SW -2 19 V 4
Input voltage SW (10 ns transient) SW -3.5 21 V 10 ns transient 4
Operating junction temperature TJ -40 150 °C 4
Storage temperature Tstg -55 150 °C 4
Supply input voltage VIN 4.5 17 V 4
Input voltage VBST VI -0.1 23 V 4
Input voltage VBST (10-ns transient) VI -0.1 26 V 10-ns transient 4
Input voltage VBST (vs SW) VBST(vs SW) -0.1 5.5 V 4
Input voltage EN EN -0.1 17 V 4
Input voltage VFB VFB -0.1 5.5 V 4
Input voltage SW SW -1.8 17 V 4
Input voltage SW (10 ns transient) SW -3.5 20 V 10 ns transient 4
Operating junction temperature TJ -40 125 °C 4
Operating, non-switching supply current IVIN 120 200 µA VIN current, EN = 5 V, VFB = 0.9 V 5
EN high-level input voltage VENH 1.6 V 5
EN low-level input voltage VENL 0.8 V 5
EN pin resistance to GND REN 600 1500 2400 kΩ VEN = 1.5 V 5
VFB threshold voltage (Eco-mode) VFBTH 774 mV VO = 1.05 V, IO = 10 mA, Eco-mode operation 5
VFB threshold voltage (continuous mode) VFBTH 749 768 787 mV VO = 1.05 V, continuous mode operation 5
VFB input current IVFB -0.1 0 0.1 µA VFB = 0.8 V 5
Current limit Iocl 2.4 3.2 4 A DC current, VOUT = 1.05 V, L1 = 2.2 µH 5
Minimum off time tOFF(MIN) 220 310 ns VFB = 0.5 V 5
UVLO wake up VIN voltage UVLO 3.8 4.3 V 5
UVLO shut down VIN voltage UVLO 3.3 3.4 V 5
Shutdown supply current IVINSDN 8 20 µA VIN current, EN = 0 V 5
EN pulldown current IEN 1 µA VEN = 1.5 V 5
High-side switch resistance RDS(on)h 140 mΩ TA = 25°C, VBST, SW = 5 V 5
Low-side switch resistance RDS(on)l 84 mΩ TA = 25°C 5
Thermal shutdown threshold TSDN 160 °C Shutdown temperature 5
Thermal shutdown hysteresis TSDN 25 °C Hysteresis 5
Soft-start time tss 1 ms Internal soft-start time 5
Switching frequency Fsw 580 kHz VIN = 12 V, VO = 3.3 V, IO = 1 A 5
Output UVP threshold VUVP 65 % Hiccup detect (H > L) 5
Hiccup wait time THICCUP_WAIT 1.2 ms 5
Hiccup time before restart THICCUP_RE 10 ms 5
UVLO hysteresis VIN voltage UVLO 0.4 V 5
Junction-to-ambient thermal resistance RθJA 90.8 °C/W 4
Junction-to-case (top) thermal resistance RθJC(top) 42.3 °C/W 4
Junction-to-board thermal resistance RθJB 16.3 °C/W 4
Junction-to-top characterization parameter ψJT 2.6 °C/W 4
Junction-to-board characterization parameter ψJB 16.3 °C/W 5

CAD (KiCad official)

  • Symbol: TPS562201DDCR
  • Footprint: Package_TO_SOT_SMD:TSOT-23-6
  • 3D model: TSOT-23-6 (KiCad packages3D, STEP)
  • 3D model files: tps562201ddcr-etched.step / tps562201ddcr-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); tps562201ddcr.step / tps562201ddcr.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (28 pp, sha256 c9aab162caefe03b, retrieved 2026-11-17, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF