3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownTPS54719RTET
Texas Instruments · DC-DC Converters · WQFN-16-EP(3x3)
TPS54719RTET from Texas Instruments, in a WQFN-16-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VIN | power_in | Input supply voltage: 2.95 V to 6 V. |
| 2 | VIN | power_in | Input supply voltage: 2.95 V to 6 V. |
| 3 | GND | power_in | Power ground; this pin should be electrically connected directly to the power pad under the IC. |
| 4 | GND | power_in | Power ground; this pin should be electrically connected directly to the power pad under the IC. |
| 5 | AGND | power_in | Analog ground should be electrically connected to GND close to the device. |
| 6 | VSENSE | input | Inverting node of the transconductance (gm) error amplifier. |
| 7 | COMP | output | Error amplifier output and input to the output switch current comparator; frequency compensation components connect to this pin. |
| 8 | RT | input | Resistor timing pin that sets the switching frequency; the datasheet gives a 16.9 kΩ minimum and 218 kΩ maximum (200 kHz to 2000 kHz). |
| 9 | SS/TR | bidirectional | Slow-start pin; an external capacitor sets the output voltage rise time, and the pin can also be used for tracking. |
| 10 | PH | output | Source of the internal high-side power MOSFET and drain of the internal low-side (synchronous) rectifier MOSFET. |
| 11 | PH | output | Source of the internal high-side power MOSFET and drain of the internal low-side (synchronous) rectifier MOSFET. |
| 12 | PH | output | Source of the internal high-side power MOSFET and drain of the internal low-side (synchronous) rectifier MOSFET. |
| 13 | BOOT | input | A bootstrap capacitor is required between BOOT and PH; if its voltage falls below the BOOT UVLO minimum, the output is forced off until the capacitor is refreshed. |
| 14 | PWRGD | output | Open-drain power-good output that asserts low if the output is out of regulation due to thermal shutdown, overcurrent, overvoltage/undervoltage, or EN shutdown; absolute maximum 7 V and 10 mA sink. |
| 15 | EN | input | Enable pin with internal pullup current source; pull below 1.18 V to disable, float to enable, and use two external resistors to set the on/off (UVLO) threshold. |
| 16 | VIN | power_in | Input supply voltage: 2.95 V to 6 V. |
| 17 | PowerPAD | power_in | GND pin that must be connected to the exposed power pad for proper operation; the pad should connect to the internal PCB ground plane through multiple vias for good thermal performance. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | WQFN-16-EP(3x3) |
| Category | Power Supply Chip |
| Pins | 17 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Operating input voltage | 2.95 | 6 | V | 5 | |||
| Internal undervoltage lockout threshold | 2.4 | 2.8 | V | Rising VIN | 5 | ||
| Shutdown supply current | 1 | 5 | µA | EN = 0 V, 2.95 V ≤ VIN ≤ 6 V | 5 | ||
| Quiescent current, Iq | Iq | 455 | 550 | µA | VSENSE = 620 mV, RT = 84 kΩ | 5 | |
| Enable threshold | 1.16 | 1.25 | 1.37 | V | Rising | 5 | |
| Voltage reference | 0.591 | 0.6 | 0.609 | V | 2.95 V ≤ VIN ≤ 6 V, -40°C < TJ < 140°C | 5 | |
| Voltage reference | 0.594 | 0.6 | 0.606 | V | 25°C | 5 | |
| High-side switch resistance | 26 | 60 | mΩ | BOOT-PH = 5 V; TJ = 25°C | 5 | ||
| High-side switch resistance | 35 | 70 | mΩ | BOOT-PH = 2.95 V; TJ = 25°C | 5 | ||
| Low-side switch resistance | 26 | 60 | mΩ | VIN = 5 V; TJ = 25°C | 5 | ||
| Low-side switch resistance | 35 | 70 | mΩ | VIN = 2.95 V; TJ = 25°C | 5 | ||
| Error amplifier source/sink current | -20 | 20 | µA | V(COMP) = 1 V, 100 mV overdrive | 5 | ||
| Current limit threshold | 8.5 | 10.5 | A | 6 | |||
| Low-side reverse current limit | -2.7 | -1.5 | A | 6 | |||
| Thermal shutdown | 150 | 155 | °C | 6 | |||
| Switching frequency range using RT mode | 200 | 2000 | kHz | using RT mode | 6 | ||
| Switching frequency | 400 | 490 | 600 | kHz | RT = 84 kΩ | 6 | |
| BOOT-PH UVLO | 2.1 | 2.75 | V | VIN = 2.95 V | 6 | ||
| SS/TR to VSENSE matching | 73 | 115 | mV | VSSTR = 0.3 V | 6 | ||
| VIN input voltage (absolute maximum) | VIN | -0.3 | 7 | V | 4 | ||
| EN input voltage (absolute maximum) | EN | -0.3 | 7 | V | 4 | ||
| VSENSE input voltage (absolute maximum) | VSENSE | -0.3 | 3 | V | 4 | ||
| COMP input voltage (absolute maximum) | COMP | -0.3 | 3 | V | 4 | ||
| PWRGD input voltage (absolute maximum) | PWRGD | -0.3 | 7 | V | 4 | ||
| SS/TR input voltage (absolute maximum) | SS/TR | -0.3 | 3 | V | 4 | ||
| RT input voltage (absolute maximum) | RT | -0.3 | 6 | V | 4 | ||
| BOOT-PH voltage (absolute maximum) | BOOT-PH | 8 | V | 4 | |||
| PH output voltage (absolute maximum) | PH | -0.6 | 7 | V | 4 | ||
| PH output voltage transient (absolute maximum) | PH | -2 | 7 | V | 10 ns transient | 4 | |
| EN source current (absolute maximum) | EN | 100 | µA | 4 | |||
| RT source current (absolute maximum) | RT | 100 | µA | 4 | |||
| COMP sink current (absolute maximum) | COMP | 100 | µA | 4 | |||
| PWRGD sink current (absolute maximum) | PWRGD | 10 | mA | 4 | |||
| SS/TR sink current (absolute maximum) | SS/TR | 100 | µA | 4 | |||
| Operating junction temperature (absolute maximum) | Tj | -40 | 140 | °C | 4 | ||
| Storage temperature (absolute maximum) | Tstg | -65 | 150 | °C | 4 | ||
| Supply voltage VIN (recommended operating) | VIN | 2.95 | 6 | V | 4 | ||
| EN input voltage (recommended operating) | EN | 0 | 6 | V | 4 | ||
| PWRGD input voltage (recommended operating) | PWRGD | 0 | 6 | V | 4 | ||
| SS/RT input voltage (recommended operating) | SS/RT | 0 | 2.7 | V | 4 | ||
| RT input voltage (recommended operating) | RT | 0 | 5.5 | V | 4 | ||
| Operating free-air temperature | TA | -40 | 85 | °C | 4 | ||
| Junction-to-ambient thermal resistance | RθJA | 49.1 | °C/W | standard board | 5 | ||
| Junction-to-ambient thermal resistance | RθJA | 37 | °C/W | custom board | 5 | ||
| Junction-to-top characterization parameter | ψJT | 0.7 | °C/W | 5 | |||
| Junction-to-board characterization parameter | ψJB | 21.8 | °C/W | 5 | |||
| Junction-to-case (top) thermal resistance | RθJC(top) | 50.7 | °C/W | 5 | |||
| Junction-to-case (bottom) thermal resistance | RθJC(bot) | 7.5 | °C/W | 5 | |||
| Junction-to-board thermal resistance | RθJB | 21.8 | °C/W | 5 |
CAD (KiCad official)
- Symbol:
TPS54719RTET - Footprint:
Package_DFN_QFN:QFN-16-1EP_3x3mm_P0.5mm_EP1.7x1.7mm - 3D model: WQFN-16-EP(3x3) (KiCad packages3D, STEP)
- 3D model files:
tps54719rtet-etched.step/tps54719rtet-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);tps54719rtet.step/tps54719rtet.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (43 pp, sha256
7441fbfc5e22b327, retrieved 2026-10-31, tier: manufacturer) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).