main
History Download
Ray tps54626pwpr: specified limits as data (metadata.characteristics, 60 rows from the datasheet) 9536955

TPS54626PWPR

Texas Instruments · DC-DC Converters · HTSSOP-14-EP

TPS54626PWPR from Texas Instruments, in a HTSSOP-14-EP. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VO power_out Connect to output of converter; also used for the output discharge function.
2 VFB input Converter feedback input; connect with a feedback resistor divider from VO.
3 VREG5 power_out 5.5V internal linear regulator output for control circuitry; a typical 1uF capacitor should be connected to GND; not active when EN is low.
4 SS passive Soft-start control pin; an external capacitor connected to GND sets the soft-start ramp time (6uA typical charge current).
5 GND power_in Signal ground pin for the control circuitry.
6 PG output Open-drain power-good output; requires an external pull-up resistor (25k-150kOhm) to VREG5.
7 EN input Enable control input, active high; must be pulled up to enable the device (internal pull-down resistance to GND of 200-800kOhm).
8 PGND1 power_in Ground return for the low-side MOSFET; also serves as an input to the current comparator; connect strongly to GND near the IC.
9 PGND2 power_in Ground return for the low-side MOSFET; also serves as an input to the current comparator; connect strongly to GND near the IC.
10 SW1 output Switch node connection between the high-side and low-side NFETs; also serves as an input to the current comparator.
11 SW2 output Switch node connection between the high-side and low-side NFETs; also serves as an input to the current comparator.
12 VBST passive Supply input for the high-side NFET gate driver (boost terminal); connect a capacitor from this pin to the SW1/SW2 terminals; an internal PN diode connects VREG5 to this pin.
13 VIN1 power_in Power input, connected to the high-side NFET drain.
14 VIN2 power_in Power input, connected to the high-side NFET drain; an additional 0.1uF capacitor from this pin to ground is recommended to improve stability of the over-current limit function.
15 PowerPAD power_in Exposed thermal pad on the package backside, internally connected to PGND; must be soldered to the PCB ground plane to achieve appropriate power dissipation.

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package HTSSOP-14-EP
Category Power Supply Chip
Pins 15

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Absolute max input voltage (VIN1, VIN2, EN) VIN1, VIN2, EN -0.3 20 V 2
Absolute max VBST voltage VBST -0.3 26 V 2
Absolute max VBST voltage (10 ns transient) VBST -0.3 28 V 10 ns transient 2
Absolute max VBST voltage vs Sw1, SW2 VBST (vs Sw1, SW2) -0.3 6.5 V 2
Absolute max VFB, VO, SS, PG voltage VFB, VO, SS, PG -0.3 6.5 V 2
Absolute max SW1, SW2 voltage SW1, SW2 -2 20 V 2
Absolute max SW1, SW2 voltage (10 ns transient) SW1, SW2 -3 22 V 10 ns transient 2
Absolute max VREG5 voltage VREG5 -0.3 6.5 V 2
Absolute max PGND1, PGND2 voltage PGND1, PGND2 -0.3 0.3 V 2
Absolute max voltage from GND to POWERPAD Vdiff -0.2 0.2 V 2
ESD rating Human Body Model 2 kV Human Body Model (HBM) 2
ESD rating Charged Device Model 500 V Charged Device Model (CDM) 2
Absolute max operating junction temperature TJ -40 150 °C 2
Absolute max storage temperature Tstg -55 150 °C 2
Supply input voltage range VIN 4.5 18 V 3
Recommended VBST voltage VBST -0.1 24 V 3
Recommended VBST voltage (10 ns transient) VBST -0.1 27 V 10 ns transient 3
Recommended VBST voltage vs SW VBST (vs SW) -0.1 6 V 3
Recommended SS, PG input voltage SS, PG -0.1 5.7 V 3
Recommended EN input voltage EN -0.1 18 V 3
Recommended VO, VFB voltage VO, VFB -0.1 5.5 V 3
Recommended SW1, SW2 voltage SW1, SW2 -1.8 18 V 3
Recommended SW1, SW2 voltage (10 ns transient) SW1, SW2 -3 21 V 10 ns transient 3
Recommended PGND1, PGND2 voltage PGND1, PGND2 -0.1 0.1 V 3
Recommended VREG5 voltage VREG5 -0.1 5.7 V 3
Recommended IVREG5 output current IVREG5 0 5 mA 3
Power Good resistor RPG RPG 25 150 kΩ 3
Operating free-air temperature TA -40 85 °C 3
Operating junction temperature TJ -40 150 °C 3
VIN operating non-switching supply current IVIN 950 1400 μA TA = 25°C, EN = 5 V, VVFB = 0.8 V 3
VIN shutdown supply current IVINSDN 3.6 10 μA TA = 25°C, EN = 0 V 3
EN high-level input voltage VENH 1.6 V 3
EN low-level input voltage VENL 0.6 V 3
EN pin resistance to GND REN 200 400 800 kΩ VEN = 12 V 3
VFB threshold voltage (continuous mode, 25°C) VFBTH 757 765 773 mV TA = 25°C, VO = 1.05 V, continuous mode 3
VFB threshold voltage (continuous mode, 0°C to 85°C) VFBTH 753 777 mV TA = 0°C to 85°C, VO = 1.05 V, continuous mode (1) 3
VFB threshold voltage (continuous mode, -40°C to 85°C) VFBTH 751 779 mV TA = –40°C to 85°C, VO = 1.05 V, continuous mode (1) 3
VFB input current IVFB -0.15 0 0.15 μA VVFB = 0.8 V, TA = 25°C 3
VO discharge resistance RDischg 100 150 Ω VEN = 0 V, VO = 0.5 V, TA = 25°C 3
VREG5 output voltage VVREG5 5.2 5.5 5.7 V TA = 25°C, 6 V < VIN < 18 V, 0 < IVREG5 < 5 mA 3
VREG5 output current IVREG5 20 mA VIN = 6 V, VVREG5 = 4 V, TA = 25°C 3
Current limit Iocl 7.2 8.2 9.5 A L = 1.5 μH (2) 4
TOFF(MIN) minimum off time TOFF(MIN) 260 310 ns TA = 25°C, VFB = 0.7 V 4
SS charge current ISSC 4.2 6 7.8 μA VSS = 1.0 V 4
SS discharge current ISSD 1.5 3.3 mA VSS = 0.5 V 4
PG threshold (VVFB rising, good) VTHPG 85 90 95 % VVFB rising (good) 4
PG sink current IPG 2.5 5 mA VPG = 0.5 V 4
Output OVP trip threshold VOVP 120 125 130 % OVP detect 4
Output UVP trip threshold VUVP 60 65 70 % UVP detect 4
UVLO wake up VREG5 voltage VUVLO 3.45 3.75 4.05 V Wake up VREG5 voltage 4
UVLO hysteresis VREG5 voltage VUVLO 0.13 0.32 0.48 V Hysteresis 4
High side switch resistance Rdsonh 36 mΩ TA = 25°C, VBST-SW1,2 = 5.5V 3
Low side switch resistance Rdsonl 28 mΩ TA = 25°C 3
On time TON 150 ns VIN = 12 V, VO = 1.05 V 4
Thermal shutdown threshold TSDN 165 °C 4
Output UVP delay TUVPDEL 0.25 ms 4
Junction-to-ambient thermal resistance θJA 40.5 °C/W PWP (14 pins) 2
Junction-to-case (top) thermal resistance θJCtop 28.7 °C/W PWP (14 pins) 2
Junction-to-board thermal resistance θJB 24.2 °C/W PWP (14 pins) 2
Junction-to-case (bottom) thermal resistance θJCbot 2.4 °C/W PWP (14 pins) 2

CAD (KiCad official)

  • Symbol: TPS54626PWPR
  • Footprint: Package_SO:TSSOP-14-1EP_4.4x5mm_P0.65mm
  • 3D model: HTSSOP-14-EP (KiCad packages3D, STEP)
  • 3D model files: tps54626pwpr-etched.step / tps54626pwpr-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); tps54626pwpr.step / tps54626pwpr.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (23 pp, sha256 6a77b8bc07cb116a, retrieved 2026-09-23, tier: lcsc)
  • Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
  • Extractor: parts-factory 2.0.0 / extract_pins 0.2, primary claude-haiku-4-5-20251001 (text), consensus claude-sonnet-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF