main
Ray
tps54394pwpr: specified limits as data (metadata.characteristics, 40 rows from the datasheet)
3df5593
TPS54394PWPR
Texas Instruments · DC-DC Converters · HTSSOP-16-EP
TPS54394PWPR from Texas Instruments, in a HTSSOP-16-EP. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VIN1 | power_in | Power input for both channels, rated 4.5V to 18V, connected to high-side NFET drains. |
| 2 | VBST1 | power_in | Bootstrap supply for channel 1 high-side FET gate driver; connect 0.1µF ceramic capacitor between VBST1 and SW1. |
| 3 | SW1 | output | Switch node output for channel 1 at junction of high-side and low-side FETs; input of current comparator. |
| 4 | PGND1 | power_in | Power ground return for channel 1 low-side MOSFET; used as reference for current sensing via SWx-PGNDx voltage measurement. |
| 5 | EN1 | input | Enable input for channel 1; pull above 2.0V to enable converter or below 0.4V to disable. |
| 6 | PG1 | output | Open-drain power good output for channel 1; goes high when output within ±16% of target after 1.5ms delay, goes low after 2µs if out of regulation. |
| 7 | VFB1 | input | D-CAP2 feedback input for channel 1; connect output voltage via resistor divider to set output voltage at 0.765V nominal. |
| 8 | GND | power_in | Signal ground; connect sensitive feedback and soft-start signal returns at a single point. |
| 9 | VREG5 | power_out | 5.5V linear regulator output; bypass with ≥1µF ceramic capacitor to GND (active when EN is high). |
| 10 | VFB2 | input | D-CAP2 feedback input for channel 2; connect output voltage via resistor divider to set output voltage at 0.765V nominal. |
| 11 | PG2 | output | Open-drain power good output for channel 2; goes high when output within ±16% of target after 1.5ms delay, goes low after 2µs if out of regulation. |
| 12 | EN2 | input | Enable input for channel 2; pull above 2.0V to enable converter or below 0.4V to disable. |
| 13 | PGND2 | power_in | Power ground return for channel 2 low-side MOSFET; used as reference for current sensing via SWx-PGNDx voltage measurement. |
| 14 | SW2 | output | Switch node output for channel 2 at junction of high-side and low-side FETs; input of current comparator. |
| 15 | VBST2 | power_in | Bootstrap supply for channel 2 high-side FET gate driver; connect 0.1µF ceramic capacitor between VBST2 and SW2. |
| 16 | VIN2 | power_in | Power input for 5.5V linear regulator, rated 4.5V to 18V. |
| 17 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | HTSSOP-16-EP |
| Category | Power Supply Chip |
| Pins | 17 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input voltage range VIN1, VIN2, EN1, EN2 | -0.3 | 20 | V | 2 | |||
| Input voltage range VBST1, VBST2 | -0.3 | 26 | V | 2 | |||
| Input voltage range VBST1, VBST2 (10ns transient) | -0.3 | 28 | V | 10ns transient | 2 | ||
| Input voltage range VBST1–SW1, VBST2–SW2 | -0.3 | 6.5 | V | 2 | |||
| Input voltage range VFB1, VFB2 | -0.3 | 6.5 | V | 2 | |||
| Input voltage range SW1, SW2 | -2 | 20 | V | 2 | |||
| Input voltage range SW1, SW2 (10ns transient) | -4.5 | 22 | V | 10ns transient | 2 | ||
| Output voltage range VREG5, PG1, PG2 | -0.3 | 6.5 | V | 2 | |||
| Output voltage range PGND1, PGND2 | -0.3 | 0.3 | V | 2 | |||
| TA Operating ambient temperature range | TA | -40 | 85 | °C | 2 | ||
| TSTG Storage temperature range | TSTG | -55 | 150 | °C | 2 | ||
| TJ Junction temperature range | TJ | -40 | 150 | °C | 2 | ||
| Supply input voltage range VIN1, VIN2 | 4.5 | 18 | V | 3 | |||
| Recommended input voltage range VBST1, VBST2 | -0.1 | 24 | V | 3 | |||
| Recommended input voltage range VBST1, VBST2 (10ns transient) | -0.1 | 27 | V | 10ns transient | 3 | ||
| Recommended input voltage range VBST1–SW1, VBST2–SW2 | -0.1 | 5.7 | V | 3 | |||
| Recommended input voltage range VFB1, VFB2 | -0.1 | 5.7 | V | 3 | |||
| Recommended input voltage range EN1, EN2 | -0.1 | 18 | V | 3 | |||
| Recommended input voltage range SW1, SW2 | -1 | 18 | V | 3 | |||
| Recommended input voltage range SW1, SW2 (10ns transient) | -4.5 | 21 | V | 10ns transient | 3 | ||
| Recommended output voltage range VREG5, PG1, PG2 | -0.1 | 5.7 | V | 3 | |||
| Recommended output voltage range PGND1, PGND2 | -0.1 | 0.1 | V | 3 | |||
| Recommended output voltage range VO1, VO2 | 0.76 | 7 | V | 3 | |||
| TA Operating free-air temperature | TA | -40 | 85 | °C | 3 | ||
| TJ Operating junction temperature | TJ | -40 | 150 | °C | 3 | ||
| VIN supply current | IIN | 1200 | 2000 | µA | TA = 25°C, EN1 = EN2 = 5 V, VFB1 = VFB2 = 0.8 V | 3 | |
| VIN shutdown current | IVINSDN | 15 | 20 | µA | TA = 25°C, EN1 = EN2 = 0 V | 3 | |
| VFBx threshold voltage | VVFBTHLx | 758 | 765 | 773 | mV | TA = 25°C, CH1 = 3.3 V, CH2 = 1.5 V | 3 |
| VFBx temperature coefficient | TCVFBx | -115 | 115 | ppm/℃ | On the basis of 25°C | 3 | |
| VFB input current | IVFBx | -0.4 | 0.2 | 0.4 | µA | VFBx = 0.8 V, TA = 25°C | 3 |
| PGx pull-down resistance | RPG | 50 | 75 | 110 | Ω | VPGx = 0.5 V | 4 |
| ENx input resistance | RENx_IN | 225 | 450 | 900 | kΩ | ENx = 12 V | 4 |
| Current limit | IOCL | 3.5 | 4.7 | 6.5 | A | LOUT = 2.2 µH | 4 |
| Output UVP trip threshold measured on VFBx | VUVP | 63 | 68 | 73 | % | measured on VFBx | 4 |
| Junction-to-ambient thermal resistance (PWP) | θJA | 41.4 | °C/W | 2 | |||
| Junction-to-case (top) thermal resistance (PWP) | θJCtop | 27.1 | °C/W | 2 | |||
| Junction-to-board thermal resistance (PWP) | θJB | 20.8 | °C/W | 2 | |||
| Junction-to-top characterization parameter (PWP) | ψJT | 1 | °C/W | 2 | |||
| Junction-to-board characterization parameter (PWP) | ψJB | 20.6 | °C/W | 2 | |||
| Junction-to-case (bottom) thermal resistance (PWP) | θJCbot | 2.7 | °C/W | 2 |
CAD (KiCad official)
- Symbol:
TPS54394PWPR - Footprint:
Package_SO:TSSOP-16-1EP_4.4x5mm_P0.65mm - 3D model: HTSSOP-16-EP (KiCad packages3D, STEP)
- 3D model files:
tps54394pwpr-etched.step/tps54394pwpr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);tps54394pwpr.step/tps54394pwpr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (32 pp, sha256
d048a180d36720dd, retrieved 2026-09-23, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.2, primaryclaude-haiku-4-5-20251001(text), consensusclaude-sonnet-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# TPS54394PWPR
**Texas Instruments** · DC-DC Converters · HTSSOP-16-EP
TPS54394PWPR from Texas Instruments, in a HTSSOP-16-EP. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VIN1 | power_in | Power input for both channels, rated 4.5V to 18V, connected to high-side NFET drains. |
| 2 | VBST1 | power_in | Bootstrap supply for channel 1 high-side FET gate driver; connect 0.1µF ceramic capacitor between VBST1 and SW1. |
| 3 | SW1 | output | Switch node output for channel 1 at junction of high-side and low-side FETs; input of current comparator. |
| 4 | PGND1 | power_in | Power ground return for channel 1 low-side MOSFET; used as reference for current sensing via SWx-PGNDx voltage measurement. |
| 5 | EN1 | input | Enable input for channel 1; pull above 2.0V to enable converter or below 0.4V to disable. |
| 6 | PG1 | output | Open-drain power good output for channel 1; goes high when output within ±16% of target after 1.5ms delay, goes low after 2µs if out of regulation. |
| 7 | VFB1 | input | D-CAP2 feedback input for channel 1; connect output voltage via resistor divider to set output voltage at 0.765V nominal. |
| 8 | GND | power_in | Signal ground; connect sensitive feedback and soft-start signal returns at a single point. |
| 9 | VREG5 | power_out | 5.5V linear regulator output; bypass with ≥1µF ceramic capacitor to GND (active when EN is high). |
| 10 | VFB2 | input | D-CAP2 feedback input for channel 2; connect output voltage via resistor divider to set output voltage at 0.765V nominal. |
| 11 | PG2 | output | Open-drain power good output for channel 2; goes high when output within ±16% of target after 1.5ms delay, goes low after 2µs if out of regulation. |
| 12 | EN2 | input | Enable input for channel 2; pull above 2.0V to enable converter or below 0.4V to disable. |
| 13 | PGND2 | power_in | Power ground return for channel 2 low-side MOSFET; used as reference for current sensing via SWx-PGNDx voltage measurement. |
| 14 | SW2 | output | Switch node output for channel 2 at junction of high-side and low-side FETs; input of current comparator. |
| 15 | VBST2 | power_in | Bootstrap supply for channel 2 high-side FET gate driver; connect 0.1µF ceramic capacitor between VBST2 and SW2. |
| 16 | VIN2 | power_in | Power input for 5.5V linear regulator, rated 4.5V to 18V. |
| 17 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | HTSSOP-16-EP |
| Category | Power Supply Chip |
| Pins | 17 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input voltage range VIN1, VIN2, EN1, EN2 | | -0.3 | | 20 | V | | 2 |
| Input voltage range VBST1, VBST2 | | -0.3 | | 26 | V | | 2 |
| Input voltage range VBST1, VBST2 (10ns transient) | | -0.3 | | 28 | V | 10ns transient | 2 |
| Input voltage range VBST1–SW1, VBST2–SW2 | | -0.3 | | 6.5 | V | | 2 |
| Input voltage range VFB1, VFB2 | | -0.3 | | 6.5 | V | | 2 |
| Input voltage range SW1, SW2 | | -2 | | 20 | V | | 2 |
| Input voltage range SW1, SW2 (10ns transient) | | -4.5 | | 22 | V | 10ns transient | 2 |
| Output voltage range VREG5, PG1, PG2 | | -0.3 | | 6.5 | V | | 2 |
| Output voltage range PGND1, PGND2 | | -0.3 | | 0.3 | V | | 2 |
| TA Operating ambient temperature range | TA | -40 | | 85 | °C | | 2 |
| TSTG Storage temperature range | TSTG | -55 | | 150 | °C | | 2 |
| TJ Junction temperature range | TJ | -40 | | 150 | °C | | 2 |
| Supply input voltage range VIN1, VIN2 | | 4.5 | | 18 | V | | 3 |
| Recommended input voltage range VBST1, VBST2 | | -0.1 | | 24 | V | | 3 |
| Recommended input voltage range VBST1, VBST2 (10ns transient) | | -0.1 | | 27 | V | 10ns transient | 3 |
| Recommended input voltage range VBST1–SW1, VBST2–SW2 | | -0.1 | | 5.7 | V | | 3 |
| Recommended input voltage range VFB1, VFB2 | | -0.1 | | 5.7 | V | | 3 |
| Recommended input voltage range EN1, EN2 | | -0.1 | | 18 | V | | 3 |
| Recommended input voltage range SW1, SW2 | | -1 | | 18 | V | | 3 |
| Recommended input voltage range SW1, SW2 (10ns transient) | | -4.5 | | 21 | V | 10ns transient | 3 |
| Recommended output voltage range VREG5, PG1, PG2 | | -0.1 | | 5.7 | V | | 3 |
| Recommended output voltage range PGND1, PGND2 | | -0.1 | | 0.1 | V | | 3 |
| Recommended output voltage range VO1, VO2 | | 0.76 | | 7 | V | | 3 |
| TA Operating free-air temperature | TA | -40 | | 85 | °C | | 3 |
| TJ Operating junction temperature | TJ | -40 | | 150 | °C | | 3 |
| VIN supply current | IIN | | 1200 | 2000 | µA | TA = 25°C, EN1 = EN2 = 5 V, VFB1 = VFB2 = 0.8 V | 3 |
| VIN shutdown current | IVINSDN | | 15 | 20 | µA | TA = 25°C, EN1 = EN2 = 0 V | 3 |
| VFBx threshold voltage | VVFBTHLx | 758 | 765 | 773 | mV | TA = 25°C, CH1 = 3.3 V, CH2 = 1.5 V | 3 |
| VFBx temperature coefficient | TCVFBx | -115 | | 115 | ppm/℃ | On the basis of 25°C | 3 |
| VFB input current | IVFBx | -0.4 | 0.2 | 0.4 | µA | VFBx = 0.8 V, TA = 25°C | 3 |
| PGx pull-down resistance | RPG | 50 | 75 | 110 | Ω | VPGx = 0.5 V | 4 |
| ENx input resistance | RENx_IN | 225 | 450 | 900 | kΩ | ENx = 12 V | 4 |
| Current limit | IOCL | 3.5 | 4.7 | 6.5 | A | LOUT = 2.2 µH | 4 |
| Output UVP trip threshold measured on VFBx | VUVP | 63 | 68 | 73 | % | measured on VFBx | 4 |
| Junction-to-ambient thermal resistance (PWP) | θJA | | 41.4 | | °C/W | | 2 |
| Junction-to-case (top) thermal resistance (PWP) | θJCtop | | 27.1 | | °C/W | | 2 |
| Junction-to-board thermal resistance (PWP) | θJB | | 20.8 | | °C/W | | 2 |
| Junction-to-top characterization parameter (PWP) | ψJT | | 1 | | °C/W | | 2 |
| Junction-to-board characterization parameter (PWP) | ψJB | | 20.6 | | °C/W | | 2 |
| Junction-to-case (bottom) thermal resistance (PWP) | θJCbot | | 2.7 | | °C/W | | 2 |
## CAD (KiCad official)
- Symbol: `TPS54394PWPR`
- Footprint: `Package_SO:TSSOP-16-1EP_4.4x5mm_P0.65mm`
- 3D model: HTSSOP-16-EP (KiCad packages3D, STEP)
- 3D model files: `tps54394pwpr-etched.step` / `tps54394pwpr-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `tps54394pwpr.step` / `tps54394pwpr.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/tps54394) (32 pp, sha256 `d048a180d36720dd`, retrieved 2026-09-23, tier: lcsc)
- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.2`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/tps54394pwpr-datasheet.pdf)