main
History Download
Ray tps54318rter: specified limits as data (metadata.characteristics, 60 rows from the datasheet) 25c734a

TPS54318RTER

Texas Instruments · DC-DC Converters · QFN-16-EP(3x3)

TPS54318RTER from Texas Instruments, in a QFN-16-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VIN power_in Input supply voltage, 2.95 V to 6 V range.
2 VIN power_in Input supply voltage, 2.95 V to 6 V range.
3 GND power_in Power ground, should be electrically connected directly to the power pad under the device.
4 GND power_in Power ground, should be electrically connected directly to the power pad under the device.
5 AGND power_in Analog ground should be electrically connected to GND close to the device.
6 VSENSE input Inverting node of the transconductance error amplifier used for output voltage feedback regulation.
7 COMP output Error amplifier output and input to the output switch current comparator; connect frequency compensation components to this pin.
8 RT/CLK bidirectional Resistor timing or external clock input pin for switching frequency adjustment (200 kHz to 2000 kHz) or external clock synchronization (300 kHz to 2000 kHz).
9 SS bidirectional Soft-start pin; external capacitor connected to this pin sets the output voltage rise time.
10 PH output Source of the internal high-side power MOSFET and drain of the internal low-side synchronous rectifier MOSFET.
11 PH output Source of the internal high-side power MOSFET and drain of the internal low-side synchronous rectifier MOSFET.
12 PH output Source of the internal high-side power MOSFET and drain of the internal low-side synchronous rectifier MOSFET.
13 BOOT input Bootstrap capacitor connection (0.1 μF ceramic required between BOOT and PH); if voltage is below minimum required by BOOT UVLO, output is forced to switch off.
14 PWRGD tri_state Open drain output that asserts low when output voltage is low due to thermal shutdown, overcurrent, over/under-voltage, or EN shutdown condition.
15 EN input Enable pin with internal pull-up current source; pull below 1.2 V to disable, float to enable, adjustable UVLO with two external resistors.
16 VIN power_in Input supply voltage, 2.95 V to 6 V range.
17 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package QFN-16-EP(3x3)
Category Power Management (PMIC)
Pins 17

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Input voltage (EN, PWRGD, VIN) -0.3 7 V 4
Input voltage (RT/CLK) -0.3 6 V 4
Input voltage (COMP, SS, VSENSE) -0.3 3 V 4
Output voltage (BOOT-PH) 8 V 4
Output voltage (PH) -0.6 7 V 4
Output voltage (PH) 10 ns transient -2 7 V 10 ns transient 4
Source current (EN, RT/CLK) 100 µA 4
Sink current (COMP, SS) 100 µA 4
Sink current (PWRGD) 10 mA 4
Operating junction temperature TJ -40 150 °C 4
Storage temperature Tstg -65 150 °C 4
ESD human body model (HBM) V(ESD) -2000 2000 V Human body model, ANSI/ESDA/JEDEC JS-001, all pins 4
ESD charged device model (CDM) V(ESD) -500 500 V Charged device model, JESD22-C101, all pins 4
Input voltage VVIN 3 6 V 4
Operating junction temperature TJ -40 150 °C 4
Operating input voltage VVIN 2.95 6 V 5
Internal under voltage lockout threshold VUVLO 2.6 2.8 V No voltage hysteresis, rising and falling 5
Shutdown supply current IQ(vin) 2 5 µA VEN = 0 V, TA = 25°C, 2.95 V ≤ VVIN ≤ 6 V 5
Quiescent current Iq 350 500 µA VVSENSE = 0.9 V, VVIN = 5 V, 25°C, RT = 400 kΩ 5
Enable threshold (rising) VTH(en) 1.16 1.25 1.37 V Rising 5
Voltage reference VREF 0.795 0.803 0.811 V 2.95 V ≤ VVIN ≤ 6 V, –40°C < TJ < 150°C 5
High-side switch resistance RDS(HFET) 30 60 mΩ (VBOOT – VPH) = 5 V 5
High-side switch resistance RDS(HFET) 44 70 mΩ (VBOOT – VPH) = 2.95 V 5
Low-side switch resistance RDS(LFET) 30 60 mΩ VVIN = 5 V 5
Low-side switch resistance RDS(LFET) 44 70 mΩ VVIN = 2.95 V 5
Error amplifier source/sink ICOMP -20 20 µA VCOMP = 1 V, 100 mV overdrive 5
Current limit threshold ILIM 3.7 5.5 A Instantaneous peak current 5
Switching frequency range using RT mode fSW 200 2000 kHz RT mode 5
Switching frequency fSW 400 500 600 kHz RRT = 400 kΩ 5
Switching frequency range using CLK mode fSW 300 2000 kHz CLK mode 5
Minimum CLK pulse width tMIN(CLK) 75 ns 5
RT/CLK high threshold VIH(CLK) 1.6 2.2 V 5
RT/CLK low threshold VIL(CLK) 0.4 0.6 V 5
Minimum on time tON(min) 60 ns Measured at 50% points on PH, IOUT = 3 6
Minimum input voltage for valid output VMIN(PG) 1.2 1.6 V VPWRGD < 0.5 V , IOUT = 100 μA 6
Low-level output voltage VOL 0.3 V IPWRGD = 3.5 mA 6
Enable threshold (falling) VTH(en) 1.18 V Falling 5
Enable pin input current IEN -3.2 µA Enable rising threshold + 50 mV 5
Enable pin input current IEN -0.65 µA Enable falling threshold – 50 mV 5
Input current IIN 7 nA 5
Error amplifier transconductance gM(ea) 225 µS –2 μA < ICOMP < 2 μA, VCOMP = 1 V 5
Error amplifier transconductance during soft-start gm(EA,ss) 70 µS –2 μA < ICOMP < 2 μA, VCOMP = 1 V, VVSENSE = 0.4 V 5
COMP to ISWITCH transconductance gM 13 A/V 5
Thermal shutdown TSD 175 °C 5
RT/CLK falling edge to PH rising edge delay tDLY 90 ns fSW = 500 kHz with RRT resistor in series 5
Minimum off time tOFF(min) 60 ns Prior to skipping off pulses, (VBOOT–VPH) = 2.95 V, IOUT = 3 6
BOOT charge resistance RBOOT 16 Ω VVIN = 5 V 6
BOOT-PH UVLO VUVLO(Boot) 2.1 V VVIN = 2.95 V 6
Charge current ICHG 1.8 µA VSS = 0.4 V 6
SS discharge current (UVLO, EN, thermal fault) IDSCHG(SS) 1.25 mA VVIN = 5 V, VSS = 0.5 V 6
VSENSE threshold (PWRGD) VTH(PG) 91 % VREF VVSENSE falling (fault) 6
VSENSE threshold (PWRGD) VTH(PG) 93 % VREF VVSENSE rising (good) 6
VSENSE threshold (PWRGD) VTH(PG) 107 % VREF VVSENSE rising (fault) 6
VSENSE threshold (PWRGD) VTH(PG) 105 % VREF VVSENSE falling (Good) 6
Minimum on time tON(min) 110 ns Measured at 50% points on PH, VIN = 5 V, IOUT = 0 A 6
Junction-to-ambient thermal resistance RθJA 50 °C/W 4
Junction-to-ambient thermal resistance (test board) RθJA 37 °C/W Test board conditions, footnote (3) 4
Junction-to-case (top) thermal resistance RθJC(top) 59.1 °C/W 4
Junction-to-board thermal resistance RθJB 23.1 °C/W 4
Junction-to-case (bottom) thermal resistance RθJC(bot) 7.9 °C/W 4

CAD (KiCad official)

  • Symbol: TPS54318RTER
  • Footprint: Package_DFN_QFN:QFN-16-1EP_3x3mm_P0.5mm_EP1.7x1.7mm
  • 3D model: QFN-16-EP(3x3) (KiCad packages3D, STEP)
  • 3D model files: tps54318rter-etched.step / tps54318rter-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); tps54318rter.step / tps54318rter.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (41 pp, sha256 1f9f20765ddc24aa, retrieved 2026-09-22, tier: lcsc)
  • Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
  • Extractor: parts-factory 2.0.0 / extract_pins 0.2, primary claude-haiku-4-5-20251001 (text), consensus claude-sonnet-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF