main
History Download
Ray tps53311rgtr: specified limits as data (metadata.characteristics, 60 rows from the datasheet) 5f54d43

TPS53311RGTR

Texas Instruments · DC-DC Converters · QFN-16-EP(3x3)

TPS53311RGTR from Texas Instruments, in a QFN-16-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 EN input Enable input. Internally pulled up to VDD with a 1.35-MΩ resistor.
2 SYNC bidirectional Synchronization signal for input interleaving. Master SYNC pin sends out 180° out-of-phase signal to slave SYNC. SYNC frequency must be within ±20% of slave nominal frequency.
3 PGD output Power good output flag, open drain output. Pull up to an external rail through a resistor.
4 VBST power_in Supply input for high-side MOSFET (bootstrap terminal). Connect capacitor from this pin to SW terminal.
5 SW bidirectional Output inductor connection to integrated power devices.
6 SW bidirectional Output inductor connection to integrated power devices.
7 SW bidirectional Output inductor connection to integrated power devices.
8 PS input Mode configuration pin (with 10 µA current): Connecting to ground for Forced CCM slave, pulled high or floating for Forced CCM master, or connect to GND with 24.3 kΩ for DE slave, 57.6 kΩ for HEF mode, 105 kΩ for reserved mode, or 174 kΩ for DE master.
9 COMP output Error amplifier compensation terminal. Type III compensation method is recommended for stability.
10 FB input Voltage feedback input. Also used for OVP, UVP, and PGD determination.
11 AGND power_in Device analog ground terminal.
12 VDD power_in Input bias supply for analog functions. Nominal 3.3-V input voltage range 2.9 V to 3.5 V.
13 VIN power_in Gate driver supply and power conversion voltage input. VIN supply voltage range 2.9 V to 6 V.
14 VIN power_in Gate driver supply and power conversion voltage input. VIN supply voltage range 2.9 V to 6 V.
15 PGND power_in IC power ground terminal.
16 PGND power_in IC power ground terminal.
17 PAD power_in Exposed thermal pad. Must be soldered to printed circuit board. Connect to power ground through multiple vias for thermal and mechanical performance.

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package QFN-16-EP(3x3)
Category Power Management (PMIC)
Pins 17

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Input voltage (VIN, EN) absolute maximum VIN, EN -0.3 7 V 4
Input voltage VBST absolute maximum VBST -0.3 17 V 4
VBST with respect to SW absolute maximum VBST(with respect to SW) -0.3 7 V 4
Input voltage FB, PS, VDD absolute maximum FB, PS, VDD -0.3 3.7 V 4
Output voltage SW DC absolute maximum SW -1 7 V 4
Output voltage SW pulse absolute maximum SW -3 10 V Pulse < 20 ns, E = 5 µJ 4
Output voltage PGD absolute maximum PGD -0.3 7 V 4
Output voltage COMP, SYNC absolute maximum COMP, SYNC -0.3 3.7 V 4
Output voltage PGND absolute maximum PGND -0.3 0.3 V 4
Operating temperature absolute maximum TA -40 85 °C 4
Junction temperature absolute maximum TJ -40 150 °C 4
Storage temperature absolute maximum Tstg -55 150 °C 4
Input voltage VIN recommended VIN 2.9 6 V 4
VDD recommended VDD 2.9 3.3 3.5 V 4
VBST recommended VBST -0.1 13.5 V 4
VBST with respect to SW recommended VBST(with respect to SW) -0.1 6 V 4
EN recommended EN -0.1 6 V 4
FB, PS recommended FB, PS -0.1 3.5 V 4
Output voltage SW recommended SW -1 6.5 V 4
PGD recommended PGD -0.1 6 V 4
COMP, SYNC recommended COMP, SYNC -0.1 3.5 V 4
PGND recommended PGND -0.1 0.1 V 4
Junction temperature recommended TJ -40 125 °C 4
VIN supply voltage VIN 2.9 6 V Nominal input voltage 5
VDD internal circuitry supply voltage VDD 2.9 3.3 3.5 V Nominal 3.3-V input voltage 5
Standby current IDD 2.2 3.5 mA EN = HI, no switching 5
VREF tolerance TOLVREF -1 1 % 0°C ≤ TA ≤ 85°C 5
VREF tolerance TOLVREF -1.25 1.25 % –40°C ≤ TA ≤ 85°C 5
Overcurrent limit on upper FET IOCPL 4.2 4.5 4.8 A 4 consecutive cycles; VIN = 3.3 V, VOUT = 1.5 V with 1-µH inductor, TA = 25°C 5
One-time overcurrent latch-off on lower FET IOCPH 4.8 5.1 5.5 A Immediate shutdown; VIN = 3.3 V, VOUT = 1.5 V with 1-µH inductor, TA = 25°C 5
Zero crossing comparator internal offset VZXOFF -4.5 -3 -1.5 mV PGND – SW, SKIP mode 5
Overvoltage protection threshold voltage VOVP 114 117 120 % Measured at FB wrt. VREF 5
Undervoltage protection threshold voltage VUVP 80 83 86 % Measured at FB wrt. VREF 5
PGD low threshold VPGDL 80 83 86 % Measured at FB wrt. VREF 5
PGD upper threshold VPGDU 114 117 120 % Measured at FB wrt. VREF 6
Thermal shutdown THSD 130 140 150 °C Latch off controller, attempt soft-stop 6
PGD pulldown voltage VPGPD 0.2 0.4 V Pulldown voltage with 4-mA sink current 6
PGD leakage current IPGLK -2 0 2 µA Hi-Z leakage current, apply 3.3-V in off state 6
EN logic high threshold VENH 1.1 1.18 1.3 V 6
EN hysteresis VENHYS 0.18 0.24 V 6
PS source pullup current IPS 8 10 12 µA When enabled 6
Slave SYNC frequency range fSYNCSL -20 20 % Versus nominal switching frequency 6
Overvoltage protection delay time tOVPDLY 1 1.7 2.5 µs Time from FB out of 20% of VREF to OVP fault 6
Switching frequency control fSW 0.99 1.1 1.21 MHz Forced CCM mode 6
Minimum OFF time tMIN(off) 100 140 ns FCCM mode or DE mode 6
Minimum OFF time tMIN(off) 175 250 ns HEF mode 6
Maximum duty cycle DMAX 84 89 % FCCM mode and DE mode, fSW = 1.1 MHz, 0°C ≤ TA ≤ 85°C 6
Maximum duty cycle DMAX 75 81 % HEF mode, fSW = 1.1 MHz, 0°C ≤ TA ≤ 85°C 6
Junction-to-ambient thermal resistance RθJA 42.8 °C/W 5
Junction-to-case (top) thermal resistance RθJC(top) 51.3 °C/W 5
Junction-to-board thermal resistance RθJB 16 °C/W 5
Junction-to-top characterization parameter ψJT 0.7 °C/W 5
Junction-to-board characterization parameter ψJB 16 °C/W 5
Junction-to-case (bottom) thermal resistance RθJC(bot) 4.4 °C/W 5
VREF internal precision reference voltage VVREF 0.6 V 5
3.3-V UVLO threshold / VIN UVLO threshold VUVLO 2.8 V Ramp up, EN = HI 5
VIN shutdown current IVINSDN 3 µA EN = LO 5
Minimum VIN voltage for valid PGD at start-up VINMINPG 1 V Measured at VIN with 1-mA (or 2-mA) sink current on PGD pin at start up 6
Soft-discharge transistor resistance RSFTSTP 60 Ω VEN = Low, VIN = 3.3 V, VOUT = 0.5 V 6
Enable pullup resistor RENPU 1.35 MΩ 6

CAD (KiCad official)

  • Symbol: TPS53311RGTR
  • Footprint: Package_DFN_QFN:QFN-16-1EP_3x3mm_P0.5mm_EP1.7x1.7mm
  • 3D model: QFN-16-EP(3x3) (KiCad packages3D, STEP)
  • 3D model files: tps53311rgtr-etched.step / tps53311rgtr-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); tps53311rgtr.step / tps53311rgtr.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (29 pp, sha256 7a23b8867ac033e6, retrieved 2026-09-24, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.2, primary claude-haiku-4-5-20251001 (text), consensus claude-sonnet-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF