main
Download ZIP Propose a change
Generated by kicad-footprint-generator · KiCad file format 20260206
Name Last commit message Last updated
docs tps43061rter: re-etch, flat white mark read from pin 1 (service-occt 1.4.0) + chip hero · Ray
viewers tps43061rter: viewers · Ray
package.json tps43061rter: component.models_3d pose record per STEP (Z-up, seated z=0, pad-centre origin, identity binding) · Ray
page.json tps43061rter: component.models_3d pose record per STEP (Z-up, seated z=0, pad-centre origin, identity binding) · Ray
README.md Initial commit: component/tps43061rter · Ray
tps43061rter-etched.fit.json tps43061rter: re-etch, flat white mark read from pin 1 (service-occt 1.4.0) + chip hero · Ray
tps43061rter-etched.glb tps43061rter: re-etch, flat white mark read from pin 1 (service-occt 1.4.0) + chip hero · Ray
tps43061rter-etched.step tps43061rter: re-etch, flat white mark read from pin 1 (service-occt 1.4.0) + chip hero · Ray
tps43061rter.glb Publish 0.1.0 · Ray
tps43061rter.kicad_mod Publish 0.1.0 · Ray
tps43061rter.kicad_sym Publish 0.1.0 · Ray
tps43061rter.lbr Publish 0.1.0 · Ray
tps43061rter.step Publish 0.1.0 · Ray

TPS43061RTER

Texas Instruments · DC-DC Converters · WQFN-16-EP(3x3)

TPS43061RTER from Texas Instruments, in a WQFN-16-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 RT/CLK input Resistor timing and external clock pin; external resistor from this pin to AGND programs switching frequency between 50 kHz and 1 MHz, or external clock between 300 kHz to 1 MHz synchronizes switching frequency.
2 SS input Soft-start programming pin; capacitor between SS pin and AGND sets soft-start time.
3 COMP output Output of internal transconductance error amplifier; feedback loop compensation network connects from this pin to AGND.
4 FB input Error amplifier input and feedback pin for voltage regulation; connect to center tap of resistor divider to set output voltage.
5 ISNS- input Inductor current sense comparator inverting input pin; normally connected to inductor side of current sense resistor.
6 ISNS+ input Inductor current sense comparator non-inverting input pin; normally connected to VIN side of current sense resistor.
7 VIN power_in Input supply pin to the IC; connect to supply voltage between 4.5 V and 38 V absolute maximum 40 V.
8 LDRV output Low-side gate driver output; connect to gate of low-side N-channel MOSFET; when VIN bias is removed, internal 200-kΩ resistor pulls LDRV to PGND.
9 PGND power_in Power ground of IC; connect to source of low-side MOSFET; PGND should be connected to AGND via single point on PCB.
10 VCC power_out Output of internal LDO and power supply for internal control circuits and gate drivers; VCC typically 5.5 V for TPS43061; connect low-ESR ceramic capacitor from this pin to PGND with recommended capacitance range 0.47 to 10 µF.
11 BOOT passive Bootstrap capacitor node for high-side MOSFET gate driver; connect bootstrap capacitor from this pin to SW pin.
12 SW passive Switching node of boost converter; connect to junction of drain of low-side MOSFET, source of high-side synchronous MOSFET, and inductor.
13 HDRV output High-side gate driver output; connect to gate of high-side synchronous rectifier MOSFET; when VIN bias is removed, internally connected to SW through 200-kΩ resistor.
14 PGOOD output Power good indicator; open-drain output indicates when output voltage is within predetermined limits; TI recommends 10-kΩ pullup resistor to VCC or external logic supply pin.
15 EN input Enable pin with internal pullup current source; floating enables IC; pull below 1.2 V for standby mode; pull below 0.4 V for shutdown mode; can implement adjustable UVLO with two resistors.
16 AGND power_in Analog signal ground of IC; AGND should be connected to PGND at single point on PCB.
17 PowerPAD passive Thermal pad should be connected to AGND; use thermal vias to connect to internal ground plane for improved power dissipation.

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package WQFN-16-EP(3x3)
Category Power Management (PMIC)
Pins 17

CAD (KiCad official)

  • Symbol: TPS43061RTER
  • Footprint: Package_DFN_QFN:QFN-16-1EP_3x3mm_P0.5mm_EP1.7x1.7mm
  • 3D model: WQFN-16-EP(3x3) (KiCad packages3D, STEP)
  • 3D model files: tps43061rter-etched.step / tps43061rter-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); tps43061rter.step / tps43061rter.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (44 pp, sha256 2cd9f6a548135d9e, retrieved 2026-09-24, tier: lcsc)
  • Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
  • Extractor: parts-factory 2.0.0 / extract_pins 0.2, primary claude-haiku-4-5-20251001 (text), consensus claude-sonnet-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF