main
Ray tps40170qrgyrq1: component.models_3d pose record per STEP (Z-up, seated z=0, pad-centre origin, identity binding) 27cad97
{
  "schema_version": 1,
  "type": "component",
  "slug": "tps40170qrgyrq1",
  "title": "TPS40170QRGYRQ1",
  "brief": "Texas Instruments AC-DC Controllers & Regulators, VQFN-20-EP(3.7x4.7). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",
  "version": "0.1.0",
  "license": "CC-BY-SA-4.0",
  "tags": [
    "component",
    "power supply chip",
    "tps40170qrgyrq1",
    "factory-2.0.0",
    "extractor-text"
  ],
  "component": {
    "mpn": "TPS40170QRGYRQ1",
    "manufacturer": "Texas Instruments",
    "package": "VQFN-20-EP(3.7x4.7)",
    "pin_count": 21,
    "category": "Power Supply Chip",
    "subcategory": "AC-DC Controllers & Regulators",
    "datasheet": "https://www.ti.com/cn/lit/gpn/tps40170-q1",
    "parts": {
      "symbol": "tps40170qrgyrq1.kicad_sym",
      "footprint": "tps40170qrgyrq1.kicad_mod",
      "model_3d": "tps40170qrgyrq1-etched.glb",
      "model_3d_plain": "tps40170qrgyrq1.glb",
      "model_3d_step": "tps40170qrgyrq1-etched.step",
      "model_3d_step_plain": "tps40170qrgyrq1.step",
      "lbr": "tps40170qrgyrq1.lbr"
    },
    "distributor_links": {
      "lcsc": "C181238"
    },
    "pins": [
      {
        "number": "1",
        "name": "ENABLE",
        "type": "input",
        "description": "Enable pin that must be high to enable the device; pull below VDIS (100 mV) to disable."
      },
      {
        "number": "2",
        "name": "SYNC",
        "type": "bidirectional",
        "description": "Synchronization pin used for frequency synchronization; output in primary mode, input in secondary 0° or 180° mode."
      },
      {
        "number": "3",
        "name": "M/S",
        "type": "input",
        "description": "Primary/secondary mode selector pin; tie to VIN for primary mode, tie to AGND or leave floating for secondary mode."
      },
      {
        "number": "4",
        "name": "RT",
        "type": "input",
        "description": "Resistor from this pin to AGND sets the oscillator frequency from 100 kHz to 600 kHz; required in all modes."
      },
      {
        "number": "5",
        "name": "SS",
        "type": "input",
        "description": "Soft-start pin; capacitor from this pin to AGND sets the soft-start time and is used for fault timing."
      },
      {
        "number": "6",
        "name": "TRK",
        "type": "input",
        "description": "Tracking input for output voltage tracking; the lesser of VTRK and the internal 600 mV reference sets the output voltage."
      },
      {
        "number": "7",
        "name": "FB",
        "type": "input",
        "description": "Feedback input to the error amplifier; output voltage is fed back through a resistor divider network."
      },
      {
        "number": "8",
        "name": "COMP",
        "type": "output",
        "description": "Output of the internal error amplifier; compensation network is connected from this pin to the FB pin."
      },
      {
        "number": "9",
        "name": "AGND",
        "type": "power_in",
        "description": "Analog signal ground; must be electrically connected to PGND externally at a single point."
      },
      {
        "number": "10",
        "name": "VDD",
        "type": "power_out",
        "description": "3.3 V regulated output; 0.1 µF to 1 µF ceramic bypass capacitor must be connected to AGND close to this pin."
      },
      {
        "number": "11",
        "name": "PGOOD",
        "type": "output",
        "description": "Open-drain power-good indicator output; 10 kΩ pullup resistor to VDD recommended; pulls low when out of regulation or faults detected."
      },
      {
        "number": "12",
        "name": "ILIM",
        "type": "input",
        "description": "Overcurrent limit pin; resistor from this pin to PGND sets the overcurrent protection threshold based on low-side FET sensing."
      },
      {
        "number": "13",
        "name": "PGND",
        "type": "power_in",
        "description": "Power ground for gate driver return path; must externally connect to AGND at a single point."
      },
      {
        "number": "14",
        "name": "LDRV",
        "type": "output",
        "description": "Gate driver output for low-side FET; resistor from this pin to PGND also sets the multiplier (3, 7, or 15) for short-circuit protection."
      },
      {
        "number": "15",
        "name": "VBP",
        "type": "power_out",
        "description": "8 V regulated output for gate driver; 1 µF to 10 µF ceramic bypass capacitor must be connected from this pin to PGND."
      },
      {
        "number": "16",
        "name": "SW",
        "type": "input",
        "description": "Switching node connection point for the synchronous buck converter; used for high-side and low-side FET current sensing for overcurrent and short-circuit protection."
      },
      {
        "number": "17",
        "name": "HDRV",
        "type": "output",
        "description": "Gate driver output for the high-side FET; referenced to SW and switches between BOOT and SW."
      },
      {
        "number": "18",
        "name": "BOOT",
        "type": "output",
        "description": "Boot-capacitor node for high-side FET gate driver; bootstrap capacitor (0.1 µF to 0.22 µF) connected from this pin to SW."
      },
      {
        "number": "19",
        "name": "VIN",
        "type": "power_in",
        "description": "Input voltage for the controller and DC-DC converter (4.5 V to 60 V); 1 µF bypass capacitor from this pin to AGND required and placed close to pin."
      },
      {
        "number": "20",
        "name": "UVLO",
        "type": "input",
        "description": "Undervoltage lockout pin; resistor divider from VIN to AGND sets the UVLO threshold; 1 nF bypass capacitor to AGND required."
      },
      {
        "number": "21",
        "name": "EP",
        "type": "passive",
        "description": "Exposed pad (from the footprint; not named in the datasheet pin table)."
      }
    ],
    "provenance": {
      "extractor": "extract_pins 0.2",
      "factory_chain": {
        "factory": "2.0.0",
        "extractor": "extract_pins 0.2",
        "primary_model": "claude-haiku-4-5-20251001",
        "primary_mode": "text",
        "consensus_model": "claude-sonnet-4-6",
        "consensus": "agreed",
        "guards": "pin_guards 0.1: passed",
        "guard_notes": [
          "extractor flagged: Package discrepancy: The MPN TPS40170QRGYRQ1 is specified in the datasheet as a VQFN-20 RGY package ",
          "exposed pad 21 added from the footprint"
        ],
        "pages_sent": 53,
        "cost_usd": 0.4846,
        "at": "2026-09-18T02:05:58"
      },
      "datasheet": {
        "url": "https://www.ti.com/cn/lit/gpn/tps40170-q1",
        "pages": 53,
        "sha256": "0fe03952f1a1b899",
        "source_tier": "lcsc"
      },
      "cad": "KiCad official (CC-BY-SA 4.0)",
      "pins": {
        "total": 21,
        "described": 21,
        "cites_pages": true,
        "refuses_to_fabricate": true
      }
    },
    "viewers": {
      "symbol": "viewers/symbol.html",
      "footprint": "viewers/footprint.html"
    },
    "models_3d": [
      {
        "file": "tps40170qrgyrq1.step",
        "role": "plain",
        "up": "Z",
        "units": "mm",
        "origin": "footprint origin = pad-pattern centre",
        "seat": "z = 0",
        "extents_mm": [
          4,
          5,
          0.77
        ],
        "zmin_mm": 0,
        "centre_offset_mm": 0,
        "footprint_binding": "identity",
        "sha256": "b7baaecccc8e434d25dca4018e56abf0d52bfa4ab833f927054939e1c879cf4e",
        "checked": "2026-10-07",
        "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"
      },
      {
        "file": "tps40170qrgyrq1-etched.step",
        "role": "eda",
        "up": "Z",
        "units": "mm",
        "origin": "footprint origin = pad-pattern centre",
        "seat": "z = 0",
        "extents_mm": [
          4,
          5,
          0.77
        ],
        "zmin_mm": 0,
        "centre_offset_mm": 0,
        "footprint_binding": "identity",
        "sha256": "afdc939e8a631e0d7c7ad2b1f40a5c28cb4c9edc7eeef5e97319cc4970a31bb6",
        "checked": "2026-10-07",
        "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"
      }
    ]
  },
  "metadata": {
    "specs": {
      "Manufacturer": "Texas Instruments",
      "Package": "VQFN-20-EP(3.7x4.7)",
      "Category": "Power Supply Chip",
      "Pins": "21"
    }
  },
  "variants": [],
  "sections": [
    "hero",
    "viewers",
    "readme",
    "breadcrumbs",
    "info"
  ],
  "discovery_triggers": [
    "tps40170qrgyrq1"
  ],
  "discovery_pitch": "TPS40170QRGYRQ1 (Texas Instruments) component page with datasheet-verified CAD.",
  "author": {
    "name": "Ray"
  },
  "dependencies": {},
  "hero": {
    "type": "image",
    "path": "docs/hero.png"
  },
  "files": [
    "page.json",
    "README.md",
    "tps40170qrgyrq1.kicad_sym",
    "tps40170qrgyrq1.kicad_mod",
    "tps40170qrgyrq1.glb",
    "tps40170qrgyrq1.step",
    "tps40170qrgyrq1.lbr",
    "docs/hero.png",
    "docs/tps40170qrgyrq1-datasheet.pdf",
    "viewers/symbol.html",
    "viewers/footprint.html"
  ],
  "visibility": {
    "public": true
  },
  "updated_at": "2026-09-25T12:03:45.888Z"
}