main
Ray
Publish 0.1.0
50bb05c
TPS3306-33QDRQ1
Texas Instruments · Supervisor And Reset ICs · SOIC-8
TPS3306-33QDRQ1 from Texas Instruments, in a SOIC-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SENSE1 | input | Sense voltage 1 input; RESET is asserted while SENSE1 is below its negative-going threshold VIT (4.55 V typ for the TPS3306-33) and the input must stay within 0 V to (VDD + 0.3 V) × VIT / 1.25 V. |
| 2 | SENSE2 | input | Sense voltage 2 input; RESET is asserted while SENSE2 is below its negative-going threshold VIT (2.93 V typ for the TPS3306-33) and the input must stay within 0 V to (VDD + 0.3 V) × VIT / 1.25 V. |
| 3 | PFI | input | Power-fail comparator input compared against an internal 1.25 V reference (VPFI typ 1.25 V), with input voltage limited to 0 V to VDD + 0.3 V; if unused, connect to ground. |
| 4 | GND | power_in | Ground reference for all device voltages, with all voltage values specified with respect to GND. |
| 5 | RESET | output | Active-low, open-drain reset output that goes low when SENSE1 or SENSE2 falls below its threshold or the watchdog times out, and it stays low for td (100 ms typ) after the monitored voltages recover. |
| 6 | PFO | output | Open-drain power-fail output that goes low when PFI falls below 1.25 V (typ) and returns high when PFI rises above about 1.25 V plus 10 mV hysteresis. |
| 7 | WDI | input | Watchdog timer input that must toggle (either edge) within the 0.5 s to 1.2 s time-out (0.8 s typ) to prevent a RESET, with VIH of 0.7 × VDD and VIL of 0.3 × VDD; leaving it unconnected disables the watchdog. |
| 8 | VDD | power_in | Supply voltage, specified from 2.7 V to 6 V (7 V absolute maximum), which must be above 1.1 V for RESET to be defined. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | SOIC-8 |
| Category | Power Management (PMIC) |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage (absolute maximum) | VDD | 7 | V | Voltages with respect to GND (Note 1) | 6 | ||
| All other pins voltage | -0.3 | 7 | V | 6 | |||
| Maximum low output current | IOL | 5 | mA | 6 | |||
| Maximum high output current | IOH | -5 | mA | 6 | |||
| Input clamp current | IIK | -20 | 20 | mA | VI < 0 or VI > VDD | 6 | |
| Output clamp current | IOK | -20 | 20 | mA | VO < 0 or VO > VDD | 6 | |
| Continuous total power dissipation | 725 | mW | Package D, TA ≤ 25°C (Dissipation Rating Table) | 6 | |||
| Operating free-air temperature range (absolute maximum) | TA | -40 | 125 | °C | 6 | ||
| Storage temperature range | Tstg | -65 | 150 | °C | 6 | ||
| Soldering temperature | 260 | °C | 6 | ||||
| Supply voltage (recommended) | VDD | 2.7 | 6 | V | 6 | ||
| Input voltage at WDI and PFI | VI | 0 | V | 6 | |||
| Input voltage at SENSE1 and SENSE2 | VI | 0 | V | 6 | |||
| Operating free-air temperature range (recommended) | TA | -40 | 125 | °C | 6 | ||
| Low-level output voltage RESET, PFO | VOL | 0.2 | V | VDD = 2.7 V to 6 V, IOL = 20 µA | 7 | ||
| Low-level output voltage RESET, PFO | VOL | 0.4 | V | VDD = 3.3 V, IOL = 2 mA | 7 | ||
| Power-up reset voltage | 0.4 | V | VDD ≥ 1.1 V, IOL = 20 µA | 7 | |||
| Negative-going input threshold voltage, SENSE1 (TPS3306-33) | VIT | 4.44 | 4.55 | 4.68 | V | VDD = 2.7 V to 6 V | 7 |
| Negative-going input threshold voltage, SENSE2 (TPS3306-33) | VIT | 2.84 | 2.93 | 3.04 | V | VDD = 2.7 V to 6 V, TA = −40°C to 125°C | 7 |
| Power-fail input threshold voltage (PFI) | VPFI | 1.2 | 1.25 | 1.3 | V | 7 | |
| Average high-level input current, WDI | IH(AV) | 100 | 150 | µA | WDI = VDD = 6 V, time average (dc = 88%) | 7 | |
| Average low-level input current, WDI | IL(AV) | -15 | -20 | µA | WDI = 0 V, VDD = 6 V, time average (dc = 12%) | 7 | |
| High-level input current, WDI | IH | 120 | 170 | µA | WDI = VDD = 6 V | 7 | |
| High-level input current, SENSE1 | IH | 5 | 10 | µA | VSENSE1 = VDD = 6 V | 7 | |
| High-level input current, SENSE2 | IH | 6 | 10 | µA | VSENSE2 = VDD = 6 V | 7 | |
| Low-level input current, WDI | IL | -120 | -170 | µA | WDI = 0 V, VDD = 6 V | 7 | |
| Input current, PFI | II | -30 | 30 | nA | VDD = 6 V, 0 V ≤ VI ≤ VDD | 7 | |
| Supply current | IDD | 15 | 40 | µA | 7 | ||
| Pulse width, SENSEn | tw | 6 | µs | VSENSEnL = VIT − 0.2 V, VSENSEnH = VIT + 0.2 V | 7 | ||
| Pulse width, WDI | tw | 100 | ns | VIH = 0.7 × VDD, VIL = 0.3 × VDD | 7 | ||
| Watchdog time-out | tt(out) | 0.5 | 0.8 | 1.2 | s | VI(SENSEn) ≥ VIT + 0.2 V | 8 |
| Delay time | td | 70 | 100 | 140 | ms | VI(SENSEn) ≥ VIT + 0.2 V | 8 |
| Propagation delay, high- to low-level output, SENSEn to RESET | tPHL | 1 | 5 | µs | VIH = VIT + 0.2 V, VIL = VIT − 0.2 V | 8 | |
| Propagation delay, high- to low-level output, PFI to PFO | tPHL | 0.5 | 1 | s | 8 | ||
| Propagation delay, low- to high-level output, PFI to PFO | tPLH | 0.5 | 1 | µs | 8 |
CAD (KiCad official)
- Symbol:
TPS3306-33QDRQ1 - Footprint:
Package_SO:SOIC-8_3.9x4.9mm_P1.27mm - 3D model: SOIC-8 (KiCad packages3D, STEP)
- 3D model files:
tps3306-33qdrq1-etched.step/tps3306-33qdrq1-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);tps3306-33qdrq1.step/tps3306-33qdrq1.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (17 pp, sha256
eef613f38c3d1330, retrieved 2026-11-10, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# TPS3306-33QDRQ1
**Texas Instruments** · Supervisor And Reset ICs · SOIC-8
TPS3306-33QDRQ1 from Texas Instruments, in a SOIC-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SENSE1 | input | Sense voltage 1 input; RESET is asserted while SENSE1 is below its negative-going threshold VIT (4.55 V typ for the TPS3306-33) and the input must stay within 0 V to (VDD + 0.3 V) × VIT / 1.25 V. |
| 2 | SENSE2 | input | Sense voltage 2 input; RESET is asserted while SENSE2 is below its negative-going threshold VIT (2.93 V typ for the TPS3306-33) and the input must stay within 0 V to (VDD + 0.3 V) × VIT / 1.25 V. |
| 3 | PFI | input | Power-fail comparator input compared against an internal 1.25 V reference (VPFI typ 1.25 V), with input voltage limited to 0 V to VDD + 0.3 V; if unused, connect to ground. |
| 4 | GND | power_in | Ground reference for all device voltages, with all voltage values specified with respect to GND. |
| 5 | RESET | output | Active-low, open-drain reset output that goes low when SENSE1 or SENSE2 falls below its threshold or the watchdog times out, and it stays low for td (100 ms typ) after the monitored voltages recover. |
| 6 | PFO | output | Open-drain power-fail output that goes low when PFI falls below 1.25 V (typ) and returns high when PFI rises above about 1.25 V plus 10 mV hysteresis. |
| 7 | WDI | input | Watchdog timer input that must toggle (either edge) within the 0.5 s to 1.2 s time-out (0.8 s typ) to prevent a RESET, with VIH of 0.7 × VDD and VIL of 0.3 × VDD; leaving it unconnected disables the watchdog. |
| 8 | VDD | power_in | Supply voltage, specified from 2.7 V to 6 V (7 V absolute maximum), which must be above 1.1 V for RESET to be defined. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | SOIC-8 |
| Category | Power Management (PMIC) |
| Pins | 8 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage (absolute maximum) | VDD | | | 7 | V | Voltages with respect to GND (Note 1) | 6 |
| All other pins voltage | | -0.3 | | 7 | V | | 6 |
| Maximum low output current | IOL | | | 5 | mA | | 6 |
| Maximum high output current | IOH | -5 | | | mA | | 6 |
| Input clamp current | IIK | -20 | | 20 | mA | VI < 0 or VI > VDD | 6 |
| Output clamp current | IOK | -20 | | 20 | mA | VO < 0 or VO > VDD | 6 |
| Continuous total power dissipation | | | | 725 | mW | Package D, TA ≤ 25°C (Dissipation Rating Table) | 6 |
| Operating free-air temperature range (absolute maximum) | TA | -40 | | 125 | °C | | 6 |
| Storage temperature range | Tstg | -65 | | 150 | °C | | 6 |
| Soldering temperature | | | | 260 | °C | | 6 |
| Supply voltage (recommended) | VDD | 2.7 | | 6 | V | | 6 |
| Input voltage at WDI and PFI | VI | 0 | | | V | | 6 |
| Input voltage at SENSE1 and SENSE2 | VI | 0 | | | V | | 6 |
| Operating free-air temperature range (recommended) | TA | -40 | | 125 | °C | | 6 |
| Low-level output voltage RESET, PFO | VOL | | | 0.2 | V | VDD = 2.7 V to 6 V, IOL = 20 µA | 7 |
| Low-level output voltage RESET, PFO | VOL | | | 0.4 | V | VDD = 3.3 V, IOL = 2 mA | 7 |
| Power-up reset voltage | | | | 0.4 | V | VDD ≥ 1.1 V, IOL = 20 µA | 7 |
| Negative-going input threshold voltage, SENSE1 (TPS3306-33) | VIT | 4.44 | 4.55 | 4.68 | V | VDD = 2.7 V to 6 V | 7 |
| Negative-going input threshold voltage, SENSE2 (TPS3306-33) | VIT | 2.84 | 2.93 | 3.04 | V | VDD = 2.7 V to 6 V, TA = −40°C to 125°C | 7 |
| Power-fail input threshold voltage (PFI) | VPFI | 1.2 | 1.25 | 1.3 | V | | 7 |
| Average high-level input current, WDI | IH(AV) | | 100 | 150 | µA | WDI = VDD = 6 V, time average (dc = 88%) | 7 |
| Average low-level input current, WDI | IL(AV) | | -15 | -20 | µA | WDI = 0 V, VDD = 6 V, time average (dc = 12%) | 7 |
| High-level input current, WDI | IH | | 120 | 170 | µA | WDI = VDD = 6 V | 7 |
| High-level input current, SENSE1 | IH | | 5 | 10 | µA | VSENSE1 = VDD = 6 V | 7 |
| High-level input current, SENSE2 | IH | | 6 | 10 | µA | VSENSE2 = VDD = 6 V | 7 |
| Low-level input current, WDI | IL | | -120 | -170 | µA | WDI = 0 V, VDD = 6 V | 7 |
| Input current, PFI | II | -30 | | 30 | nA | VDD = 6 V, 0 V ≤ VI ≤ VDD | 7 |
| Supply current | IDD | | 15 | 40 | µA | | 7 |
| Pulse width, SENSEn | tw | 6 | | | µs | VSENSEnL = VIT − 0.2 V, VSENSEnH = VIT + 0.2 V | 7 |
| Pulse width, WDI | tw | 100 | | | ns | VIH = 0.7 × VDD, VIL = 0.3 × VDD | 7 |
| Watchdog time-out | tt(out) | 0.5 | 0.8 | 1.2 | s | VI(SENSEn) ≥ VIT + 0.2 V | 8 |
| Delay time | td | 70 | 100 | 140 | ms | VI(SENSEn) ≥ VIT + 0.2 V | 8 |
| Propagation delay, high- to low-level output, SENSEn to RESET | tPHL | | 1 | 5 | µs | VIH = VIT + 0.2 V, VIL = VIT − 0.2 V | 8 |
| Propagation delay, high- to low-level output, PFI to PFO | tPHL | | 0.5 | 1 | s | | 8 |
| Propagation delay, low- to high-level output, PFI to PFO | tPLH | | 0.5 | 1 | µs | | 8 |
## CAD (KiCad official)
- Symbol: `TPS3306-33QDRQ1`
- Footprint: `Package_SO:SOIC-8_3.9x4.9mm_P1.27mm`
- 3D model: SOIC-8 (KiCad packages3D, STEP)
- 3D model files: `tps3306-33qdrq1-etched.step` / `tps3306-33qdrq1-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `tps3306-33qdrq1.step` / `tps3306-33qdrq1.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/lit/ds/symlink/tps3306-q1.pdf) (17 pp, sha256 `eef613f38c3d1330`, retrieved 2026-11-10, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/tps3306-33qdrq1-datasheet.pdf)