main
History Download
Ray Publish 0.1.0 f807535

TPS26614DDFR

Texas Instruments · LED Drivers · TSOT-23-8

TPS26614DDFR from Texas Instruments, in a TSOT-23-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 GND power_in Reference ground for all internal voltages; connect to GND of the ±Vs supply.
2 MODE input MODE selection pin for overload response, setting the current limit to IOL, 2 × IOL, or 2 × IOL with extended IOL expiry time; the recommended MODE voltage range is 0 V to 3 V.
3 -Vs power_in Negative supply for dual-supply configurations, with a recommended range of -20 V to 0 V and an absolute maximum of -22 V to 0.3 V; connect to GND in a single-supply configuration.
4 IN power_in Signal/power input with a recommended IN voltage range of -50 V to 50 V and an absolute maximum of ±55 V.
5 OUT power_out Signal/power output; the device limits current to IOL of 32 mA typical in the fixed bidirectional current limit.
6 +Vs power_in Positive supply for powering the device, with a recommended range of 0 V to 30 V and an absolute maximum of 32 V.
7 EN input Enable control for the TPS26614; pull low to turn off the device, with an internal pullup so it can be left floating to enable it, and a recommended voltage range of 0 V to 5 V.
8 SGOOD output Signal-good indicator that goes low during normal operation and can drive an external LED, with a maximum sink current of 200 µA.

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package TSOT-23-8
Category Nixie Tube Driver/LED Driver
Pins 8

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
IN, OUT, IN-OUT voltage -55 55 V 4
SGOOD, EN, MODE, VSNS voltage -0.3 5.5 V 4
+Vs supply voltage -0.3 32 V 4
-Vs supply voltage -22 0.3 V 4
ISGOOD source current ISGOOD 200 µA 4
Operating junction temperature TJ -40 150 °C 4
Storage temperature Tstg -65 150 °C 4
IN, OUT voltage -50 50 V 4
+Vs supply voltage +Vs 0 30 V 4
-Vs supply voltage -Vs -20 0 V 4
EN, SGOOD, VSNS voltage 0 5 V 4
MODE voltage 0 3 V 4
Operating junction temperature TJ -40 125 °C 4
Junction-to-ambient thermal resistance RθJA 117.8 °C/W 4
Junction-to-case (top) thermal resistance RθJC(top) 57.6 °C/W 4
Junction-to-board thermal resistance RθJB 40.2 °C/W 4
Junction-to-top characterization parameter ΨJT 2.2 °C/W 4
Junction-to-board characterization parameter ΨJB 40 °C/W 5
IN signal voltage V(IN) -50 50 V 5
Leakage current from IN and OUT to GND in normal operation IQ -0.1 0.1 µA (-Vs) < VIN, VOUT < (+Vs, 0.35 V) 5
Leakage current from IN and OUT to GND in normal operation IQ 1 µA (+Vs, 0.35 V) < VIN, VOUT < +Vs 5
Bipolar current limit I(OL) 25 32 40 mA V(IN)-V(OUT) = ±1 V, -Vs connected to negative supply 5
Unipolar current limit I(OL) 25 32 40 mA V(IN)-V(OUT) = +1 V, -Vs connected to GND 5
Unipolar current limit with VIN < -VS (TPS26613/14 only) I(OL) -40 -32 -25 mA V(IN) = -24 V, V(OUT) = -19 V, -Vs = -20 V 5
Transient pulse over current limit I(OL_Pulse) 50 60 72 mA V(IN)-V(OUT) = +1.5 V, MODE = Floating 5
Sum of leakage current from IN and OUT in Off state (Source) IOff-Lkg-IN + IOff-Lkg-OUT -9.75 -5.25 µA -12.5 V < VIN < 12.5 V; VOUT = 0 V; EN = Low; +Vs = 15 V; -Vs = -15 V 5
Leakage current from IN pin in Off state (Source) IOff-Lkg-IN -6 -1 µA -12.5 V < VIN < 12.5 V; VOUT = 0 V; EN = Low; +Vs = 15 V; -Vs = -15 V 5
Leakage current from OUT pin in Off state (Source) IOff-Lkg-OUT -6 -1 µA -12.5 V < VOUT < 12.5 V; VIN = 0 V; EN = Low; +Vs = 15 V; -Vs = -15 V 5
OUT overvoltage hysteresis VOUT_OVLO_hyst 30 75 mV 5
OUT undervoltage hysteresis (TPS26613/14 only) VO_UVLO_hyst 30 75 mV 6
+Vs supply operating voltage (TPS26610/11/13/14) V(+Vs) 2.25 30 V 6
-Vs supply operating voltage V(-Vs) -20 0 V 6
Difference between +Vs and -Vs Vs_DIFF 3 50 V 6
Current sourced from +Vs supply to GND in normal operation I(+Vs) 1.07 1.65 mA SGOOD = Floating 6
Current sourced from +Vs supply to GND in fault operation I(+Vs) 1.2 1.75 mA SGOOD = Floating 6
OFF state supply current (TPS26611/12/14 only) IVS_OFF 0.27 mA EN = Low 6
IN to OUT total ON resistance RON 4.8 7.5 12.5 Ω -40 ℃ < T < 125 ℃, I(IN) < Overload Current 6
EN open circuit voltage (TPS26611/12/14) V(EN) 2.1 2.5 V I(EN) = -0.1 µA 6
EN leakage current (Sink) I(EN_LKG) 10 µA V(EN) = 5.5 V 6
EN leakage current (Source) I(EN_LKG) -10 µA V(EN) = 0 V 6
EN rising threshold V(ENR) 1.72 V 6
EN falling threshold V(ENF) 1 V 6
SGOOD output level, HIGH VOH_SGOOD 2 3 V (+Vs) > 2.5 V, 0 mA < ISGOOD < 1 mA 7
SGOOD pull down impedance RSGOOD 6.3 kΩ 0 µA < ISGOOD < 200 µA 7
MODE source current I(MODE) 1.55 2 2.4 µA 7
Mode selection resistor RMODE 180 kΩ 7
Thermal shutdown threshold, rising T(TSD) 160 °C 7
Thermal shutdown hysteresis T(TSDHyst) 11 °C 7
Input small signal bandwidth BW 10 kHz -25 mA < IIN < 25 mA, ΔIIN = 1 mApp at 1 kΩ 7
Turn ON delay with Vs/-Vs supply tON_dly 120 µs Delay from +Vs/-Vs supply applied to FET on, EN = Floating 7
Turn OFF delay with +Vs/-Vs supply tOFF_dly 10 µs Delay from +Vs/-Vs supply removed to FET off, EN = Floating 7
Turn ON delay with EN pin tON_EN_dly 120 µs Delay from EN HIGH to FET on 7
Turn OFF delay with EN pin tOFF_EN_dly 10 µs Delay from EN LOW to FET off 7
Overload current limit response time tOL 30 55 µs Load transient from 20 mA to 50 mA; time to current within 20% of IOL 7
Pulse overload current limit response time tOL_PULSE 20 50 µs Load transient from 20 mA to 80 mA; time to current within 20% of IOL_Pulse 7
Fast-trip response time tFASTRIP 5 µs MODE = GND, current exceeding 120 mA to FET off 7
SGOOD deglitch delay during assertion TSG_Deglitch 685 µs Deglitch delay during SGOOD assertion 7
SGOOD deglitch delay during de-assertion TSG_Deglitch 1.3 ms Deglitch delay during SGOOD de-assertion 7
OUT OVLO cutoff detection time tOUT_OV_CUT 1 5 µs V(OUT) ↑ 100 mV above VOUT_OVLO to FET OFF 7

CAD (KiCad official)

  • Symbol: TPS26614DDFR
  • Footprint: Package_TO_SOT_SMD:TSOT-23-8
  • 3D model: TSOT-23-8 (KiCad packages3D, STEP)
  • 3D model files: tps26614ddfr-etched.step / tps26614ddfr-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); tps26614ddfr.step / tps26614ddfr.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (45 pp, sha256 22fc9c245d7926dd, retrieved 2026-11-02, tier: manufacturer)
  • Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF