component
TPS259824LNRGER
Public Made by Adomby adom
Texas Instruments Supervisor And Reset ICs, VQFN-24(4x4). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
Generated by kicad-footprint-generator · KiCad file format 20260206
| Name | Last updated |
|---|---|
| docs | 1d ago |
| viewers | 1d ago |
| package.json | 1d ago |
| page.json | 1d ago |
| README.md | 1d ago |
| tps259824lnrger-etched.glb | 1d ago |
| tps259824lnrger-etched.step | 1d ago |
| tps259824lnrger-hero.glb | 1d ago |
| tps259824lnrger-hero.overlay.json | 1d ago |
| tps259824lnrger.glb | 1d ago |
| tps259824lnrger.kicad_mod | 1d ago |
| tps259824lnrger.kicad_sym | 1d ago |
| tps259824lnrger.lbr | 1d ago |
| tps259824lnrger.step | 1d ago |
TPS259824LNRGER
Texas Instruments · Supervisor And Reset ICs · VQFN-24(4x4)
TPS259824LNRGER from Texas Instruments, in a VQFN-24(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | IN | power_in | Power input to the eFuse; the operating input range is 2.7 V to 24 V, with an absolute maximum of 30 V. |
| 2 | IN | power_in | Power input to the eFuse; the operating input range is 2.7 V to 24 V, with an absolute maximum of 30 V. |
| 3 | IN | power_in | Power input to the eFuse; the operating input range is 2.7 V to 24 V, with an absolute maximum of 30 V. |
| 4 | GND | power_in | Ground connection to the system ground, used as the reference for all internal signals. |
| 5 | GND | power_in | Ground connection to the system ground, used as the reference for all internal signals. |
| 6 | EN/UVLO | input | Active-high enable with an external resistor divider from IN to GND to set the UVLO threshold; it must not be left floating and its absolute maximum is 7 V. |
| 7 | ITIMER | output | A capacitor to GND sets the overcurrent blanking interval; leave it open for the fastest response, and shorting it to GND triggers a device fault. |
| 8 | ILIM | output | A resistor to GND sets the output current-limit and fast-trip thresholds; the recommended RILIM range is 82 Ω to 1650 Ω and the pin must not be left floating. |
| 9 | IMON | output | Analog load-current monitor output that sources current proportional to the load current (gain 246 µA/A typical); a resistor to GND converts it to a voltage. |
| 10 | RETRY_DLY | output | A capacitor to GND sets the delay before an automatic restart attempt after a fault; connecting this pin to GND selects latch-off with no auto-retry. |
| 11 | NRETRY | output | A capacitor to GND sets the number of automatic restart attempts after a fault; connecting this pin to GND selects infinite retries. |
| 12 | LDSTRT | input | Load-detect/handshake input where a capacitor to GND sets the time window in which the load must pull this pin low after PG asserts; connect to GND if unused and do not leave it floating. |
| 13 | PG | output | Active-high power-good open-drain output that requires an external pull-up, is asserted when the FET is fully enhanced and the output reaches its maximum voltage, and is held low when VIN is below VUVP. |
| 14 | GND | power_in | Ground connection to the system ground, used as the reference for all internal signals. |
| 15 | dVdt | output | A capacitor to GND sets the output turn-on slew rate; leave it open for the fastest slew rate during startup. |
| 16 | IN | power_in | Power input to the eFuse; the operating input range is 2.7 V to 24 V, with an absolute maximum of 30 V. |
| 17 | OUT | power_out | Power output to the load; the device can carry a continuous switch current of up to 15 A from IN to OUT. |
| 18 | OUT | power_out | Power output to the load; the device can carry a continuous switch current of up to 15 A from IN to OUT. |
| 19 | OUT | power_out | Power output to the load; the device can carry a continuous switch current of up to 15 A from IN to OUT. |
| 20 | OUT | power_out | Power output to the load; the device can carry a continuous switch current of up to 15 A from IN to OUT. |
| 21 | OUT | power_out | Power output to the load; the device can carry a continuous switch current of up to 15 A from IN to OUT. |
| 22 | OUT | power_out | Power output to the load; the device can carry a continuous switch current of up to 15 A from IN to OUT. |
| 23 | OUT | power_out | Power output to the load; the device can carry a continuous switch current of up to 15 A from IN to OUT. |
| 24 | OUT | power_out | Power output to the load; the device can carry a continuous switch current of up to 15 A from IN to OUT. |
| 25 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | VQFN-24(4x4) |
| Category | Power Management (PMIC) |
| Pins | 25 |
CAD (KiCad official)
- Symbol:
TPS259824LNRGER - Footprint:
Package_DFN_QFN:QFN-24-1EP_4x4mm_P0.5mm_EP2.7x2.7mm - 3D model: VQFN-24(4x4) (KiCad packages3D, STEP)
- 3D model files:
tps259824lnrger-etched.step/tps259824lnrger-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);tps259824lnrger.step/tps259824lnrger.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (55 pp, sha256
f4a0f06cfbd81f26, retrieved 2026-10-08, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).