component
TPS25940AQRVCTQ1
Public Made by Adomby adom
Texas Instruments Surge Protection Devices (SPDs), WQFN-20(4x3). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
← Commit history
tps25940aqrvctq1: component.models_3d pose record per STEP (Z-up, seated z=0, pad-centre origin, identity binding)
2 files changed
+97−17
package.json+55−15@@ -68,25 +68,25 @@ "number": "1", "name": "DEVSLP", "type": "input",- "description": "Active-high DevSleep low-power mode control; rising threshold 1.6 V min / 1.85 V typ / 2.0 V max, falling 0.8 V min / 0.96 V typ / 1.1 V max; input leakage 0.6-1.25 \u00b5A; leave floating or connect to GND if unused."+ "description": "Active-high DevSleep low-power mode control; rising threshold 1.6 V min / 1.85 V typ / 2.0 V max, falling 0.8 V min / 0.96 V typ / 1.1 V max; input leakage 0.6-1.25 µA; leave floating or connect to GND if unused." }, { "number": "2", "name": "PGOOD", "type": "output",- "description": "Active-high open-drain power-good output; asserted high when PGTH > V(PGTHR) = 0.99 V (typ) and internal FET is fully enhanced; internal pull-down 10-35 \u03a9; max sink current 10 mA; leave floating if unused."+ "description": "Active-high open-drain power-good output; asserted high when PGTH > V(PGTHR) = 0.99 V (typ) and internal FET is fully enhanced; internal pull-down 10-35 Ω; max sink current 10 mA; leave floating if unused." }, { "number": "3", "name": "PGTH", "type": "input",- "description": "Positive input of the internal power-good comparator; rising threshold V(PGTHR) = 0.97-1.01 V, falling V(PGTHF) = 0.90-0.94 V; leakage \u00b1100 nA max; connect to OUT or GND if unused."+ "description": "Positive input of the internal power-good comparator; rising threshold V(PGTHR) = 0.97-1.01 V, falling V(PGTHF) = 0.90-0.94 V; leakage ±100 nA max; connect to OUT or GND if unused." }, { "number": "4", "name": "OUT", "type": "power_out",- "description": "Switched power output; one of five paralleled OUT pins (4-8); total RON = 34-64 m\u03a9 (-40 \u00b0C to +125 \u00b0C); max continuous switch current 4.78 A at TA = 85 \u00b0C; all OUT pins must be tied together and connected to the load."+ "description": "Switched power output; one of five paralleled OUT pins (4-8); total RON = 34-64 mΩ (-40 °C to +125 °C); max continuous switch current 4.78 A at TA = 85 °C; all OUT pins must be tied together and connected to the load." }, { "number": "5",@@ -116,7 +116,7 @@ "number": "9", "name": "IN", "type": "power_in",- "description": "Power input and device supply voltage; operating range 2.7 V to 18 V (20 V abs max, 22 V for 10 ms transient); IQ(ON) = 140-270 \u00b5A; one of five paralleled IN pins (9-13); all IN pins must be connected together."+ "description": "Power input and device supply voltage; operating range 2.7 V to 18 V (20 V abs max, 22 V for 10 ms transient); IQ(ON) = 140-270 µA; one of five paralleled IN pins (9-13); all IN pins must be connected together." }, { "number": "10",@@ -146,49 +146,49 @@ "number": "14", "name": "EN/UVLO", "type": "input",- "description": "Enable and programmable undervoltage lockout input; FET turns off when V < V(ENF) = 0.92 V (typ); device enters low-IQ shutdown (IQ < 15 \u00b5A) when V < V(SHUTF) = 0.47 V (typ); pin must not be left floating; connect to IN if UVLO not needed."+ "description": "Enable and programmable undervoltage lockout input; FET turns off when V < V(ENF) = 0.92 V (typ); device enters low-IQ shutdown (IQ < 15 µA) when V < V(SHUTF) = 0.47 V (typ); pin must not be left floating; connect to IN if UVLO not needed." }, { "number": "15", "name": "OVP", "type": "input",- "description": "Overvoltage protection threshold-setting input; FET opens and FLT asserts when V(OVP) > V(OVPR) = 0.99 V (typ); OVP disable delay 2 \u00b5s (typ); tie to GND when not used; leakage \u00b1100 nA max."+ "description": "Overvoltage protection threshold-setting input; FET opens and FLT asserts when V(OVP) > V(OVPR) = 0.99 V (typ); OVP disable delay 2 µs (typ); tie to GND when not used; leakage ±100 nA max." }, { "number": "16", "name": "GND", "type": "power_in",- "description": "Ground reference for all voltages; must be connected to the exposed PowerPAD (pin 21); PowerPAD must be soldered to PCB ground plane with multiple vias for thermal performance; R\u03b8JCbot = 3.4 \u00b0C/W."+ "description": "Ground reference for all voltages; must be connected to the exposed PowerPAD (pin 21); PowerPAD must be soldered to PCB ground plane with multiple vias for thermal performance; RθJCbot = 3.4 °C/W." }, { "number": "17", "name": "ILIM", "type": "passive",- "description": "Current-limit programming pin; external resistor from ILIM to GND sets overload and short-circuit current limit via I(LIM) = 89 / R(ILIM); V(ILIM) bias = 0.87 V (typ); R(ILIM) range 16.9 k\u03a9 to 150 k\u03a9 corresponding to I(LIM) 5.3 A to 0.6 A (\u00b18% accuracy)."+ "description": "Current-limit programming pin; external resistor from ILIM to GND sets overload and short-circuit current limit via I(LIM) = 89 / R(ILIM); V(ILIM) bias = 0.87 V (typ); R(ILIM) range 16.9 kΩ to 150 kΩ corresponding to I(LIM) 5.3 A to 0.6 A (±8% accuracy)." }, { "number": "18", "name": "dVdT", "type": "passive",- "description": "Output voltage ramp-rate control pin; external capacitor from dVdT to GND sets output slew rate; I(dVdT) charging current = 1 \u00b5A (typ), V(dVdTmax) = 2.88 V (typ), GAIN(dVdT) = 11.9 V/V (typ); leave floating for internal 30 V/ms ramp; C(dVdT) up to 470 nF."+ "description": "Output voltage ramp-rate control pin; external capacitor from dVdT to GND sets output slew rate; I(dVdT) charging current = 1 µA (typ), V(dVdTmax) = 2.88 V (typ), GAIN(dVdT) = 11.9 V/V (typ); leave floating for internal 30 V/ms ramp; C(dVdT) up to 470 nF." }, { "number": "19", "name": "IMON", "type": "output",- "description": "Analog current monitor output; sources a scaled current proportional to I(OUT) with GAIN(IMON) = 52.3 \u00b5A/A (typ), accuracy \u00b18% for TPS25940A-Q1; external resistor from IMON to GND converts to voltage; max output voltage min([V(IN) - 2.2 V], 6 V); leave floating if unused."+ "description": "Analog current monitor output; sources a scaled current proportional to I(OUT) with GAIN(IMON) = 52.3 µA/A (typ), accuracy ±8% for TPS25940A-Q1; external resistor from IMON to GND converts to voltage; max output voltage min([V(IN) - 2.2 V], 6 V); leave floating if unused." }, { "number": "20", "name": "FLT", "type": "output",- "description": "Active-low open-drain fault indicator; asserts low for undervoltage, overvoltage, reverse voltage (V(REVTH) = -66 mV typ), or thermal shutdown events; internal pull-down resistance 10-30 \u03a9; max sink current 10 mA; leave open or tie to GND if unused."+ "description": "Active-low open-drain fault indicator; asserts low for undervoltage, overvoltage, reverse voltage (V(REVTH) = -66 mV typ), or thermal shutdown events; internal pull-down resistance 10-30 Ω; max sink current 10 mA; leave open or tie to GND if unused." }, { "number": "21", "name": "EP", "type": "power_in",- "description": "Exposed PowerPAD (thermal pad); at GND potential; R\u03b8JCbot = 3.4 \u00b0C/W; must be soldered to PCB ground plane with multiple vias for optimal thermal and mechanical performance."+ "description": "Exposed PowerPAD (thermal pad); at GND potential; RθJCbot = 3.4 °C/W; must be soldered to PCB ground plane with multiple vias for optimal thermal and mechanical performance." } ], "provenance": {@@ -225,6 +225,46 @@ "viewers": { "symbol": "viewers/symbol.html", "footprint": "viewers/footprint.html"- }+ },+ "models_3d": [+ {+ "file": "tps25940aqrvctq1.step",+ "role": "plain",+ "up": "Z",+ "units": "mm",+ "origin": "footprint origin = pad-pattern centre",+ "seat": "z = 0",+ "extents_mm": [+ 3.0,+ 4.0,+ 0.77+ ],+ "zmin_mm": 0.0,+ "centre_offset_mm": 0.0,+ "footprint_binding": "identity",+ "sha256": "9305bb1f2217b3a3c4923c5aad9089084cd988b0009a6b8028004dfc00dac347",+ "checked": "2026-10-07",+ "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+ },+ {+ "file": "tps25940aqrvctq1-etched.step",+ "role": "eda",+ "up": "Z",+ "units": "mm",+ "origin": "footprint origin = pad-pattern centre",+ "seat": "z = 0",+ "extents_mm": [+ 3.0,+ 4.0,+ 0.77+ ],+ "zmin_mm": 0.0,+ "centre_offset_mm": 0.0,+ "footprint_binding": "identity",+ "sha256": "ca9cb3d801b127e68016f6827efdf58e5c540d4b53213e2b6b5bd77c0a441bb7",+ "checked": "2026-10-07",+ "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+ }+ ] }-}+}
page.json+42−2@@ -210,7 +210,47 @@ "viewers": { "symbol": "viewers/symbol.html", "footprint": "viewers/footprint.html"- }+ },+ "models_3d": [+ {+ "file": "tps25940aqrvctq1.step",+ "role": "plain",+ "up": "Z",+ "units": "mm",+ "origin": "footprint origin = pad-pattern centre",+ "seat": "z = 0",+ "extents_mm": [+ 3.0,+ 4.0,+ 0.77+ ],+ "zmin_mm": 0.0,+ "centre_offset_mm": 0.0,+ "footprint_binding": "identity",+ "sha256": "9305bb1f2217b3a3c4923c5aad9089084cd988b0009a6b8028004dfc00dac347",+ "checked": "2026-10-07",+ "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+ },+ {+ "file": "tps25940aqrvctq1-etched.step",+ "role": "eda",+ "up": "Z",+ "units": "mm",+ "origin": "footprint origin = pad-pattern centre",+ "seat": "z = 0",+ "extents_mm": [+ 3.0,+ 4.0,+ 0.77+ ],+ "zmin_mm": 0.0,+ "centre_offset_mm": 0.0,+ "footprint_binding": "identity",+ "sha256": "ca9cb3d801b127e68016f6827efdf58e5c540d4b53213e2b6b5bd77c0a441bb7",+ "checked": "2026-10-07",+ "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+ }+ ] }, "metadata": { "specs": {@@ -257,4 +297,4 @@ "visibility": { "public": true }-}+}