Made with KiCad 10.0 · needs KiCad 10.0 or later to open · KiCad file format 20260206
TPS2561DRCT
Texas Instruments · Integrated Circuits (ICs) · 10-VFDFN Exposed Pad
TPS2561DRCT from Texas Instruments, in a 10-VFDFN Exposed Pad. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | GND | power_in | Ground connection; connect externally to the thermal pad. |
| 2 | IN | power_in | Input voltage; connect a 0.1 μF or greater ceramic capacitor from IN to GND as close to the IC as possible. |
| 3 | IN | power_in | Input voltage; connect a 0.1 μF or greater ceramic capacitor from IN to GND as close to the IC as possible. |
| 4 | EN1 | input | Enable input for TPS2561, logic high turns on channel one power switch. |
| 5 | EN2 | input | Enable input for TPS2561, logic high turns on channel two power switch. |
| 6 | FAULT2 | output | Active-low open-drain output, asserted during overcurrent or overtemperature condition on channel two. |
| 7 | ILIM | passive | External resistor used to set current-limit threshold; recommended 20 kΩ ≤ RILIM ≤ 187 kΩ. |
| 8 | OUT2 | power_out | Power-switch output for channel two. |
| 9 | OUT1 | power_out | Power-switch output for channel one. |
| 10 | FAULT1 | output | Active-low open-drain output, asserted during overcurrent or overtemperature condition on channel one. |
| 11 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | 10-VFDFN Exposed Pad |
| Category | Integrated Circuits (ICs) |
| Pins | 11 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input voltage | VIN | 2.5 | 6.5 | V | 4 | ||
| TPS2561 enable voltage | VENx | 0 | 6.5 | V | 4 | ||
| High-level input voltage on ENx or ENx | VIH | 1.1 | V | 4 | |||
| Low-level input voltage on ENx or ENx | VIL | 0.66 | V | 4 | |||
| Continuous output current per channel | IOUTx | 0 | 2.5 | A | 4 | ||
| Continuous FAULTx sink current (recommended) | 0 | 10 | mA | 4 | |||
| Recommended resistor limit | RILIM | 20 | 187 | kΩ | 4 | ||
| Operating junction temperature | TJ | -40 | 125 | °C | 4 | ||
| Voltage on IN, ENx or ENx, ILIM, FAULTx | -0.3 | 7 | V | Voltages referenced to GND | 4 | ||
| Voltage on OUTx | OUTx | -0.8 | 7 | V | Voltages referenced to GND | 4 | |
| Voltage from IN to OUTx | -7 | 7 | V | 4 | |||
| Continuous FAULTx sink current (absolute maximum) | 25 | mA | 4 | ||||
| Maximum junction temperature | TJ | -40 | °C | MAX column prints OTSD2 (ambient over temperature shutdown threshold, see footnote 3) | 4 | ||
| Human-body model ESD | V(ESD) | -2000 | 2000 | V | Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001 | 4 | |
| Charged-device model ESD | V(ESD) | -500 | 500 | V | Charged-device model (CDM), per JEDEC JESD22-C101 | 4 | |
| IEC 61000-4-2 contact discharge ESD | V(ESD) | -8000 | 8000 | V | IEC 61000-4-2 contact discharge | 4 | |
| IEC 61000-4-2 air-gap discharge ESD | V(ESD) | -15000 | 15000 | V | IEC 61000-4-2 air-gap discharge | 4 | |
| Static drain-source on-state resistance per channel, TJ = 25 °C | rDS(on) | 44 | 50 | mΩ | TJ = 25 °C, IN to OUTx | 5 | |
| Static drain-source on-state resistance per channel, -40 °C ≤ TJ ≤ 125 °C | rDS(on) | 70 | mΩ | -40 °C ≤ TJ ≤ 125 °C, IN to OUTx | 5 | ||
| Rise time, output | tr | 2 | 3 | 4 | ms | CLx = 1 μF, RLx = 100 Ω, VIN = 6.5 V (see Figure 8-1) | 5 |
| Rise time, output | tr | 1 | 2 | 3 | ms | CLx = 1 μF, RLx = 100 Ω, VIN = 2.5 V (see Figure 8-1) | 5 |
| Fall time, output | tf | 0.6 | 0.8 | 1 | ms | CLx = 1 μF, RLx = 100 Ω, VIN = 6.5 V (see Figure 8-1) | 5 |
| Fall time, output | tf | 0.4 | 0.6 | 0.8 | ms | CLx = 1 μF, RLx = 100 Ω, VIN = 2.5 V (see Figure 8-1) | 5 |
| Enable pin turn on/off threshold | 0.66 | 1.1 | V | 5 | |||
| Input current | IEN | -0.5 | 0.5 | μA | VENx = 0 V or 6.5 V, V/ENx = 0 V or 6.5 V | 5 | |
| Current-limit threshold per channel, RILIM = 20 kΩ | IOS | 2590 | 2800 | 3005 | mA | RILIM = 20 kΩ | 5 |
| Current-limit threshold per channel, RILIM = 61.9 kΩ | IOS | 800 | 900 | 1005 | mA | RILIM = 61.9 kΩ | 5 |
| Current-limit threshold per channel, RILIM = 100 kΩ | IOS | 470 | 560 | 645 | mA | RILIM = 100 kΩ | 5 |
| Supply current, low-level output (output disabled) | IIN_off | 0.1 | 2 | μA | VIN = 6.5 V, no load on OUTx, VENx = 6.5 V or VENx = 0 V | 6 | |
| Supply current, high-level output (output enabled), RILIM = 20 kΩ | IIN_on | 100 | 125 | μA | VIN = 6.5 V, no load on OUTx, RILIM = 20 kΩ | 6 | |
| Supply current, high-level output (output enabled), RILIM = 100 kΩ | IIN_on | 85 | 110 | μA | VIN = 6.5 V, no load on OUTx, RILIM = 100 kΩ | 6 | |
| Reverse leakage current | IREV | 0.01 | 1 | μA | VOUTx = 6.5 V, VIN = 0 V, TJ = 25°C | 6 | |
| Undervoltage lockout, low-level input voltage, IN | UVLO | 2.35 | 2.45 | V | VIN rising | 6 | |
| Output low voltage, FAULTx | VOL | 180 | mV | IFAULTx = 1 mA | 6 | ||
| Off-state leakage, FAULTx | 1 | μA | VFAULTx = 6.5 V | 6 | |||
| FAULTx deglitch | 6 | 9 | 13 | ms | FAULTx assertion or de-assertion due to overcurrent condition | 6 | |
| Thermal shutdown threshold (ambient) | OTSD2 | 155 | °C | 6 | |||
| Thermal shutdown threshold in current limit | OTSD | 135 | °C | Thermal shutdown threshold in current-limit | 6 | ||
| Turnon time | ton | 9 | ms | CLx = 1 μF, RLx = 100 Ω (see Figure 8-1) | 5 | ||
| Turnoff time | toff | 6 | ms | CLx = 1 μF, RLx = 100 Ω (see Figure 8-1) | 5 | ||
| Response time to short circuit | tIOS | 3.5 | μs | VIN = 5.0 V (see Figure 8-2) | 5 | ||
| Hysteresis, enable pin | 55 | mV | 5 | ||||
| Hysteresis, IN (undervoltage lockout) | 35 | mV | TJ = 25°C | 6 | |||
| Hysteresis, thermal shutdown | 20 | °C | 6 | ||||
| Junction-to-ambient thermal resistance | RθJA | 47.8 | °C/W | 5 | |||
| Junction-to-case (top) thermal resistance | RθJC(top) | 66.2 | °C/W | 5 | |||
| Junction-to-board thermal resistance | RθJB | 22.4 | °C/W | 5 | |||
| Junction-to-top characterization parameter | ψJT | 1.6 | °C/W | 5 | |||
| Junction-to-board characterization parameter | ψJB | 22.6 | °C/W | 5 | |||
| Junction-to-case (bottom) thermal resistance | RθJC(bot) | 4.9 | °C/W | 5 | |||
| Junction-to-ambient thermal resistance (high-K board) | RθJA | 41.6 | °C/W | High-K (2s2p) JEDEC board, PowerPAD mounting | 6 | ||
| Junction-to-case thermal resistance (high-K board) | RθJC | 10.7 | °C/W | High-K (2s2p) JEDEC board, PowerPAD mounting | 6 | ||
| Power rating | 2403 | mW | TA ≤ 25°C, High-K board | 6 |
CAD (KiCad official)
- Symbol:
TPS2561DRCT - Footprint:
Package_SON:Texas_DRC0010J - 3D model: 10-VFDFN Exposed Pad, generated on the KiCad land (body 3 x 3 mm, terminals on the pads, 0.9 mm tall, given). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
- 3D model files:
tps2561drct-etched.step/tps2561drct-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);tps2561drct.step/tps2561drct.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (30 pp, sha256
3c66a28fc3932400, retrieved 2026-11-17, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0). Land: footprint: KiCad Texas_DRC0010J, checked against datasheet pitch/pin count/body/ep/drawing (outline drawing DRC0010J; pitch 0.5 mm; body 3.0 x 3.0 mm; 11 terminals; exposed pad 1.65 x 2.4 mm, p.27).