Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

TPS2561DRCT

Texas Instruments · Integrated Circuits (ICs) · 10-VFDFN Exposed Pad

TPS2561DRCT from Texas Instruments, in a 10-VFDFN Exposed Pad. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 GND power_in Ground connection; connect externally to the thermal pad.
2 IN power_in Input voltage; connect a 0.1 μF or greater ceramic capacitor from IN to GND as close to the IC as possible.
3 IN power_in Input voltage; connect a 0.1 μF or greater ceramic capacitor from IN to GND as close to the IC as possible.
4 EN1 input Enable input for TPS2561, logic high turns on channel one power switch.
5 EN2 input Enable input for TPS2561, logic high turns on channel two power switch.
6 FAULT2 output Active-low open-drain output, asserted during overcurrent or overtemperature condition on channel two.
7 ILIM passive External resistor used to set current-limit threshold; recommended 20 kΩ ≤ RILIM ≤ 187 kΩ.
8 OUT2 power_out Power-switch output for channel two.
9 OUT1 power_out Power-switch output for channel one.
10 FAULT1 output Active-low open-drain output, asserted during overcurrent or overtemperature condition on channel one.
11 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package 10-VFDFN Exposed Pad
Category Integrated Circuits (ICs)
Pins 11

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Input voltage VIN 2.5 6.5 V 4
TPS2561 enable voltage VENx 0 6.5 V 4
High-level input voltage on ENx or ENx VIH 1.1 V 4
Low-level input voltage on ENx or ENx VIL 0.66 V 4
Continuous output current per channel IOUTx 0 2.5 A 4
Continuous FAULTx sink current (recommended) 0 10 mA 4
Recommended resistor limit RILIM 20 187 kΩ 4
Operating junction temperature TJ -40 125 °C 4
Voltage on IN, ENx or ENx, ILIM, FAULTx -0.3 7 V Voltages referenced to GND 4
Voltage on OUTx OUTx -0.8 7 V Voltages referenced to GND 4
Voltage from IN to OUTx -7 7 V 4
Continuous FAULTx sink current (absolute maximum) 25 mA 4
Maximum junction temperature TJ -40 °C MAX column prints OTSD2 (ambient over temperature shutdown threshold, see footnote 3) 4
Human-body model ESD V(ESD) -2000 2000 V Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001 4
Charged-device model ESD V(ESD) -500 500 V Charged-device model (CDM), per JEDEC JESD22-C101 4
IEC 61000-4-2 contact discharge ESD V(ESD) -8000 8000 V IEC 61000-4-2 contact discharge 4
IEC 61000-4-2 air-gap discharge ESD V(ESD) -15000 15000 V IEC 61000-4-2 air-gap discharge 4
Static drain-source on-state resistance per channel, TJ = 25 °C rDS(on) 44 50 mΩ TJ = 25 °C, IN to OUTx 5
Static drain-source on-state resistance per channel, -40 °C ≤ TJ ≤ 125 °C rDS(on) 70 mΩ -40 °C ≤ TJ ≤ 125 °C, IN to OUTx 5
Rise time, output tr 2 3 4 ms CLx = 1 μF, RLx = 100 Ω, VIN = 6.5 V (see Figure 8-1) 5
Rise time, output tr 1 2 3 ms CLx = 1 μF, RLx = 100 Ω, VIN = 2.5 V (see Figure 8-1) 5
Fall time, output tf 0.6 0.8 1 ms CLx = 1 μF, RLx = 100 Ω, VIN = 6.5 V (see Figure 8-1) 5
Fall time, output tf 0.4 0.6 0.8 ms CLx = 1 μF, RLx = 100 Ω, VIN = 2.5 V (see Figure 8-1) 5
Enable pin turn on/off threshold 0.66 1.1 V 5
Input current IEN -0.5 0.5 μA VENx = 0 V or 6.5 V, V/ENx = 0 V or 6.5 V 5
Current-limit threshold per channel, RILIM = 20 kΩ IOS 2590 2800 3005 mA RILIM = 20 kΩ 5
Current-limit threshold per channel, RILIM = 61.9 kΩ IOS 800 900 1005 mA RILIM = 61.9 kΩ 5
Current-limit threshold per channel, RILIM = 100 kΩ IOS 470 560 645 mA RILIM = 100 kΩ 5
Supply current, low-level output (output disabled) IIN_off 0.1 2 μA VIN = 6.5 V, no load on OUTx, VENx = 6.5 V or VENx = 0 V 6
Supply current, high-level output (output enabled), RILIM = 20 kΩ IIN_on 100 125 μA VIN = 6.5 V, no load on OUTx, RILIM = 20 kΩ 6
Supply current, high-level output (output enabled), RILIM = 100 kΩ IIN_on 85 110 μA VIN = 6.5 V, no load on OUTx, RILIM = 100 kΩ 6
Reverse leakage current IREV 0.01 1 μA VOUTx = 6.5 V, VIN = 0 V, TJ = 25°C 6
Undervoltage lockout, low-level input voltage, IN UVLO 2.35 2.45 V VIN rising 6
Output low voltage, FAULTx VOL 180 mV IFAULTx = 1 mA 6
Off-state leakage, FAULTx 1 μA VFAULTx = 6.5 V 6
FAULTx deglitch 6 9 13 ms FAULTx assertion or de-assertion due to overcurrent condition 6
Thermal shutdown threshold (ambient) OTSD2 155 °C 6
Thermal shutdown threshold in current limit OTSD 135 °C Thermal shutdown threshold in current-limit 6
Turnon time ton 9 ms CLx = 1 μF, RLx = 100 Ω (see Figure 8-1) 5
Turnoff time toff 6 ms CLx = 1 μF, RLx = 100 Ω (see Figure 8-1) 5
Response time to short circuit tIOS 3.5 μs VIN = 5.0 V (see Figure 8-2) 5
Hysteresis, enable pin 55 mV 5
Hysteresis, IN (undervoltage lockout) 35 mV TJ = 25°C 6
Hysteresis, thermal shutdown 20 °C 6
Junction-to-ambient thermal resistance RθJA 47.8 °C/W 5
Junction-to-case (top) thermal resistance RθJC(top) 66.2 °C/W 5
Junction-to-board thermal resistance RθJB 22.4 °C/W 5
Junction-to-top characterization parameter ψJT 1.6 °C/W 5
Junction-to-board characterization parameter ψJB 22.6 °C/W 5
Junction-to-case (bottom) thermal resistance RθJC(bot) 4.9 °C/W 5
Junction-to-ambient thermal resistance (high-K board) RθJA 41.6 °C/W High-K (2s2p) JEDEC board, PowerPAD mounting 6
Junction-to-case thermal resistance (high-K board) RθJC 10.7 °C/W High-K (2s2p) JEDEC board, PowerPAD mounting 6
Power rating 2403 mW TA ≤ 25°C, High-K board 6

CAD (KiCad official)

  • Symbol: TPS2561DRCT
  • Footprint: Package_SON:Texas_DRC0010J
  • 3D model: 10-VFDFN Exposed Pad, generated on the KiCad land (body 3 x 3 mm, terminals on the pads, 0.9 mm tall, given). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
  • 3D model files: tps2561drct-etched.step / tps2561drct-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); tps2561drct.step / tps2561drct.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (30 pp, sha256 3c66a28fc3932400, retrieved 2026-11-17, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0). Land: footprint: KiCad Texas_DRC0010J, checked against datasheet pitch/pin count/body/ep/drawing (outline drawing DRC0010J; pitch 0.5 mm; body 3.0 x 3.0 mm; 11 terminals; exposed pad 1.65 x 2.4 mm, p.27).

Datasheet PDF