main
Ray tps2320ipwr: component.models_3d pose record per STEP (Z-up, seated z=0, pad-centre origin, identity binding) 6d3d051
{
  "schema_version": 1,
  "type": "component",
  "slug": "tps2320ipwr",
  "title": "TPS2320IPWR",
  "brief": "Texas Instruments Supervisor And Reset ICs, TSSOP-16. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",
  "version": "0.1.0",
  "license": "CC-BY-SA-4.0",
  "tags": [
    "component",
    "power management (pmic)",
    "tps2320ipwr",
    "factory-2.0.0",
    "extractor-text"
  ],
  "component": {
    "mpn": "TPS2320IPWR",
    "manufacturer": "Texas Instruments",
    "package": "TSSOP-16",
    "pin_count": 16,
    "category": "Power Management (PMIC)",
    "subcategory": "Supervisor And Reset ICs",
    "datasheet": "https://www.ti.com/cn/lit/gpn/tps2320",
    "parts": {
      "symbol": "tps2320ipwr.kicad_sym",
      "footprint": "tps2320ipwr.kicad_mod",
      "model_3d": "tps2320ipwr-etched.glb",
      "model_3d_plain": "tps2320ipwr.glb",
      "model_3d_step": "tps2320ipwr-etched.step",
      "model_3d_step_plain": "tps2320ipwr.step",
      "lbr": "tps2320ipwr.lbr"
    },
    "distributor_links": {
      "lcsc": "C2678291"
    },
    "pins": [
      {
        "number": "1",
        "name": "GATE1",
        "type": "output",
        "description": "Gate drive output for channel 1 high-side MOSFET, 10-20 µA source and 50-100 µA sink current, 9-12 V gate-to-source clamp, 30 V maximum rating."
      },
      {
        "number": "2",
        "name": "GATE2",
        "type": "output",
        "description": "Gate drive output for channel 2 high-side MOSFET, 10-20 µA source and 50-100 µA sink current, 9-12 V gate-to-source clamp, 22 V maximum rating."
      },
      {
        "number": "3",
        "name": "DGND",
        "type": "power_in",
        "description": "Digital ground reference, connect to AGND as close as possible."
      },
      {
        "number": "4",
        "name": "TIMER",
        "type": "output",
        "description": "Overcurrent timing node with 50 µA charge current and 2.5 mA discharge current, capacitor charging to 0.5 V threshold triggers circuit-breaker latch."
      },
      {
        "number": "5",
        "name": "VREG",
        "type": "power_out",
        "description": "Regulated 3.5-5.5 V regulator output powered from IN1, requires 0.1 µF bypass capacitor to ground for stable operation."
      },
      {
        "number": "6",
        "name": "AGND",
        "type": "power_in",
        "description": "Analog ground reference, connect to DGND as close as possible."
      },
      {
        "number": "7",
        "name": "ISENSE2",
        "type": "input",
        "description": "Channel 2 current-sense input connected to voltage across sense resistor between IN2 and MOSFET drain, voltage must not exceed VI(IN2)."
      },
      {
        "number": "8",
        "name": "ISENSE1",
        "type": "input",
        "description": "Channel 1 current-sense input connected to voltage across sense resistor between IN1 and MOSFET drain, voltage must not exceed VI(IN1)."
      },
      {
        "number": "9",
        "name": "IN1",
        "type": "power_in",
        "description": "Primary power input 3-13 V, supplies device operating current for both channels and feeds internal LDO for VREG regulator."
      },
      {
        "number": "10",
        "name": "IN2",
        "type": "power_in",
        "description": "Secondary power input 3-5.5 V for channel 2 only, independent power rail from IN1."
      },
      {
        "number": "11",
        "name": "ISET2",
        "type": "input",
        "description": "Channel 2 current-limit setting input, external resistor to IN2 sets overcurrent threshold with 50 µA internal current source pulldown."
      },
      {
        "number": "12",
        "name": "ISET1",
        "type": "input",
        "description": "Channel 1 current-limit setting input, external resistor to IN1 sets overcurrent threshold with 50 µA internal current source pulldown."
      },
      {
        "number": "13",
        "name": "FAULT",
        "type": "output",
        "description": "Open-drain overcurrent fault output pulled low when overcurrent condition persists until TIMER reaches 0.5 V, latches until device reset or enable toggle."
      },
      {
        "number": "14",
        "name": "ENABLE",
        "type": "input",
        "description": "Active-low TTL/CMOS compatible enable input for TPS2320, 2 V high threshold and 0.8 V low threshold, disables gates when pulled high."
      },
      {
        "number": "15",
        "name": "DISCH2",
        "type": "output",
        "description": "Channel 2 discharge transistor output connected to external MOSFET source, provides gate voltage clamping reference and 10 mA discharge current for load capacitance."
      },
      {
        "number": "16",
        "name": "DISCH1",
        "type": "output",
        "description": "Channel 1 discharge transistor output connected to external MOSFET source, provides gate voltage clamping reference and 10 mA discharge current for load capacitance."
      }
    ],
    "provenance": {
      "extractor": "extract_pins 0.2",
      "factory_chain": {
        "factory": "2.0.0",
        "extractor": "extract_pins 0.2",
        "primary_model": "claude-haiku-4-5-20251001",
        "primary_mode": "text",
        "consensus_model": "claude-sonnet-5",
        "consensus": "agreed",
        "guards": "pin_guards 0.1: passed",
        "guard_notes": [],
        "pages_sent": 29,
        "cost_usd": 0.3274,
        "at": "2026-09-24T08:43:11"
      },
      "datasheet": {
        "url": "https://www.ti.com/cn/lit/gpn/tps2320",
        "pages": 29,
        "sha256": "0c4eed4165426632",
        "source_tier": "lcsc"
      },
      "cad": "KiCad official (CC-BY-SA 4.0)",
      "pins": {
        "total": 16,
        "described": 16,
        "cites_pages": true,
        "refuses_to_fabricate": true
      }
    },
    "viewers": {
      "symbol": "viewers/symbol.html",
      "footprint": "viewers/footprint.html"
    },
    "models_3d": [
      {
        "file": "tps2320ipwr.step",
        "role": "plain",
        "up": "Z",
        "units": "mm",
        "origin": "footprint origin = pad-pattern centre",
        "seat": "z = 0",
        "extents_mm": [
          6.4,
          5,
          1.1
        ],
        "zmin_mm": 0,
        "centre_offset_mm": 0,
        "footprint_binding": "identity",
        "sha256": "6ad5e98224d02a427d9a6b929a28dbc158b9925fba5adec12db05079f1016948",
        "checked": "2026-10-07",
        "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"
      },
      {
        "file": "tps2320ipwr-etched.step",
        "role": "eda",
        "up": "Z",
        "units": "mm",
        "origin": "footprint origin = pad-pattern centre",
        "seat": "z = 0",
        "extents_mm": [
          6.4,
          5,
          1.1
        ],
        "zmin_mm": 0,
        "centre_offset_mm": 0,
        "footprint_binding": "identity",
        "sha256": "814b6c66dd6a418ae2a3a590419d59560c58906c7e8d51e940ed81ac49938f7d",
        "checked": "2026-10-07",
        "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"
      }
    ]
  },
  "metadata": {
    "specs": {
      "Manufacturer": "Texas Instruments",
      "Package": "TSSOP-16",
      "Category": "Power Management (PMIC)",
      "Pins": "16"
    }
  },
  "variants": [],
  "sections": [
    "hero",
    "viewers",
    "readme",
    "breadcrumbs",
    "info"
  ],
  "discovery_triggers": [
    "tps2320ipwr"
  ],
  "discovery_pitch": "TPS2320IPWR (Texas Instruments) component page: datasheet pinout, KiCad symbol, footprint and 3D.",
  "author": {
    "name": "Ray"
  },
  "dependencies": {},
  "hero": {
    "type": "image",
    "path": "docs/hero.png"
  },
  "files": [
    "page.json",
    "README.md",
    "tps2320ipwr.kicad_sym",
    "tps2320ipwr.kicad_mod",
    "tps2320ipwr.glb",
    "tps2320ipwr.step",
    "tps2320ipwr.lbr",
    "docs/hero.png",
    "docs/tps2320ipwr-datasheet.pdf",
    "viewers/symbol.html",
    "viewers/footprint.html"
  ],
  "visibility": {
    "public": true
  }
}