main
Ray Publish 0.1.0 a2ae1e1

TPS1HB08BQPWPRQ1

Texas Instruments · Power Distribution Switches · HTSSOP-16

TPS1HB08BQPWPRQ1 from Texas Instruments, in a HTSSOP-16. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 GND power_in Device ground reference for all pin voltages; reverse ground current is limited to -50 mA (absolute maximum) when VBB < 0 V.
2 SNS output Analog sense output that sources a current proportional to load current or device temperature into an external RSNS (1 kΩ typical), and also signals faults as ISNSFH; ground through 1 kΩ if unused.
3 LATCH input Sets fault handling behavior: when high, a fault latches the switch off until LATCH is low; when low or floating (through RPROT), the device auto-retries; input voltage range -1 V to 5.5 V.
4 EN input Active-high control input with VIL of 0.8 V maximum and VIH of 2.0 V minimum, and an absolute voltage range of -1 V to 7 V.
5 ILIM output Connect a resistor (5 kΩ to 25 kΩ) from this pin to VBB to set the current-limit threshold; if left floating, the device uses the default internal current limit.
6 VOUT output Channel output to the load; internally clamped (VDS clamp 40 V min, 46 V typ) to limit FET voltage when switching off inductive loads.
7 VOUT output Channel output to the load; internally clamped (VDS clamp 40 V min, 46 V typ) to limit FET voltage when switching off inductive loads.
8 VOUT output Channel output to the load; internally clamped (VDS clamp 40 V min, 46 V typ) to limit FET voltage when switching off inductive loads.
9 VOUT output Channel output to the load; internally clamped (VDS clamp 40 V min, 46 V typ) to limit FET voltage when switching off inductive loads.
10 VOUT output Channel output to the load; internally clamped (VDS clamp 40 V min, 46 V typ) to limit FET voltage when switching off inductive loads.
11 VOUT output Channel output to the load; internally clamped (VDS clamp 40 V min, 46 V typ) to limit FET voltage when switching off inductive loads.
12 NC unconnected No connect; leave floating.
13 NC unconnected No connect; leave floating.
14 SEL1 input Diagnostics select that chooses device temperature sensing when high (no function on Version F); if unused it must be grounded through RPROT (15 kΩ typical) to enable automatic FET turn-on during reverse battery.
15 NC unconnected No connect; leave floating.
16 DIA_EN input Diagnostic enable, active high with VIL of 0.8 V maximum and VIH of 2.0 V minimum; when unused, the analog sense, open-load and short-to-battery diagnostics are unavailable.
17 VBB power_in Power supply input (exposed thermal pad) with 6 V to 18 V nominal range, 36 V maximum continuous and 40 V load-dump withstand.

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package HTSSOP-16
Category Power Management (PMIC)
Pins 17

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Maximum continuous supply voltage VBB 36 V 6
Load dump voltage VLD 40 V ISO16750-2:2010(E) 6
Reverse battery voltage VRev, t -18 V t ≤ 3 minutes 6
Enable pin voltage VEN -1 7 V 6
LATCH pin voltage VLATCH -1 7 V 6
Diagnostic Enable pin voltage VDIA_EN -1 7 V 6
Sense pin voltage VSNS -1 18 V 6
Select pin voltage VSEL -1 7 V 6
Reverse ground current IGND -50 mA VBB < 0V 6
Energy dissipation during turnoff, single pulse ETOFF 95 mJ Single pulse, LOUT = 5mH, TJ,start = 125°C 6
Energy dissipation during turnoff, repetitive pulse ETOFF 56 mJ Repetitive pulse, LOUT = 5mH, TJ,start = 125°C 6
Maximum junction temperature TJ 150 °C 6
Storage temperature Tstg -65 150 °C 6
VBB nominal supply voltage VBB 6 18 V 6
VBB extended lower supply voltage VBB 3 6 V 6
VBB extended higher supply voltage VBB 18 28 V 6
Enable voltage VEN -1 5.5 V 6
LATCH voltage VLATCH -1 5.5 V 6
Diagnostic Enable voltage VDIA_EN -1 5.5 V 6
Select voltage VSEL1 -1 5.5 V 6
Sense voltage VSNS -1 7 V 6
VBB undervoltage lockout falling VUVLOF 2 3 V Measured with respect to the GND pin of the device 7
VBB undervoltage lockout rising VUVLOR 2.2 3 V Measured with respect to the GND pin of the device 7
VDS clamp voltage VDSCLAMP 40 46 V 7
VBB clamp voltage VBBCLAMP 58 76 V 7
Standby current (total device leakage including MOSFET) ISB 0.1 µA VBB = 13.5V, TJ = 25°C, VEN = VDIA_EN = 0V, VOUT = 0V 7
Standby current (total device leakage including MOSFET) ISB 0.5 µA VBB = 13.5V, TJ = 85°C, VEN = VDIA_EN = 0V, VOUT = 0V 7
Output leakage current IOUT(standby) 0.01 0.5 µA VBB = 13.5V, TJ = 25°C, VEN = VDIA_EN = 0V, VOUT = 0V 7
Output leakage current IOUT(standby) 3 µA VBB = 13.5V, TJ = 125°C, VEN = VDIA_EN = 0V, VOUT = 0V 7
Current consumption in diagnostic mode IDIA 3 6 mA VBB = 13.5V, ISNS = 0mA, VEN = 0V, VDIA_EN = 5V, VOUT = 0V 7
Quiescent current IQ 3 6 mA VBB = 13.5V, VEN = VDIA_EN = 5V, IOUT = 0A 7
Standby mode delay time tSTBY 12 17 22 ms VEN = VDIA_EN = 0V to standby 7
On-resistance (includes MOSFET and package) RON 8 mΩ TJ = 25°C, 6V ≤ VBB ≤ 28V 7
On-resistance (includes MOSFET and package) RON 16 mΩ TJ = 150°C, 6V ≤ VBB ≤ 28V 7
On-resistance (includes MOSFET and package) RON 12 mΩ TJ = 25°C, 3V ≤ VBB ≤ 6V 7
On-resistance during reverse polarity RON(REV) 8 mΩ TJ = 25°C, -18V ≤ VBB ≤ -8V 7
On-resistance during reverse polarity RON(REV) 16 mΩ TJ = 105°C, -18V ≤ VBB ≤ -8V 7
Current sense current accuracy ISNSI -5 5.3 % VEN = VDIA_EN = 5V, VSEL1 = 0V, IOUT = 10A 8
Current sense current accuracy ISNSI -4.6 6.2 % VEN = VDIA_EN = 5V, VSEL1 = 0V, IOUT = 300mA 8
Current sense current accuracy ISNSI -13.6 15.1 % VEN = VDIA_EN = 5V, VSEL1 = 0V, IOUT = 100mA 8
Current sense current accuracy ISNSI -56 57.3 % VEN = VDIA_EN = 5V, VSEL1 = 0V, IOUT = 20mA 8
Fault high-level current on SNS ISNSFH 4 4.5 5.3 mA VDIA_EN = 5V, VSEL1 = 0V 8
Short circuit maximum supply voltage (Version B) VSC 18 V Version B 8
Current limit threshold (Version B) ICL 47.1 70 84.2 A Device Version B, TJ = -40°C to 150°C, RILIM = 5kΩ 8
Current limit threshold (Version B) ICL 9.9 14 17.8 A Device Version B, TJ = -40°C to 150°C, RILIM = 25kΩ 8
Current limit ratio (Version B) KCL 245 350 437.5 A * kΩ Version B 8
Open-load (OL) detection voltage VOL 2 3 4 V VEN = 0V, VDIA_EN = 5V, VSEL1 = 0V 8
OL and STB indication time from EN falling tOL1 300 500 700 µs VEN = 5V to 0V, VDIA_EN = 5V, VSEL1 = 0V, IOUT = 0mA, VOUT = 4V 9
Thermal shutdown TABS 150 °C 9
Thermal shutdown hysteresis THYS 20 25 30 °C 9
Retry time tRETRY 1 2 3 ms Time from fault shutdown until switch re-enable (thermal shutdown or current limit) 9
EN input voltage low-level VIL, EN 0.8 V No GND network diode 9
EN input voltage high-level VIH, EN 2 V No GND network diode 9
Turnon delay time (from Active) tDR 20 60 100 µs VBB = 13.5V, RL = 2.6Ω, 50% EN rising to 10% VOUT rising 10
Turnoff delay time tDF 20 60 100 µs VBB = 13.5V, RL = 2.6Ω, 50% EN falling to 90% VOUT falling 10
Turnon time (active) tON 39 94 235 µs VBB = 13.5V, RL = 2.6Ω, 50% EN rising to 80% VOUT rising 10
Turnoff time tOFF 39 94 235 µs VBB = 13.5V, RL = 2.6Ω, 50% EN falling to 20% VOUT falling 10
VOUT rising slew rate SRR 0.1 0.4 0.7 V/µs VBB = 13.5V, 20% to 80% of VOUT, RL = 2.6Ω 10
Junction-to-ambient thermal resistance RθJA 32.6 °C/W 7

CAD (KiCad official)

  • Symbol: TPS1HB08BQPWPRQ1
  • Footprint: Package_SO:TSSOP-16-1EP_4.4x5mm_P0.65mm
  • 3D model: HTSSOP-16 (KiCad packages3D, STEP)
  • 3D model files: tps1hb08bqpwprq1-etched.step / tps1hb08bqpwprq1-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); tps1hb08bqpwprq1.step / tps1hb08bqpwprq1.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (54 pp, sha256 8f2664df02ed6b2e, retrieved 2026-11-10, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF