Made with KiCad 10.0 · needs KiCad 10.0 or later to open · KiCad file format 20260206
TPS1HB08BQPWPRQ1
Texas Instruments · Power Distribution Switches · HTSSOP-16
TPS1HB08BQPWPRQ1 from Texas Instruments, in a HTSSOP-16. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | GND | power_in | Device ground reference for all pin voltages; reverse ground current is limited to -50 mA (absolute maximum) when VBB < 0 V. |
| 2 | SNS | output | Analog sense output that sources a current proportional to load current or device temperature into an external RSNS (1 kΩ typical), and also signals faults as ISNSFH; ground through 1 kΩ if unused. |
| 3 | LATCH | input | Sets fault handling behavior: when high, a fault latches the switch off until LATCH is low; when low or floating (through RPROT), the device auto-retries; input voltage range -1 V to 5.5 V. |
| 4 | EN | input | Active-high control input with VIL of 0.8 V maximum and VIH of 2.0 V minimum, and an absolute voltage range of -1 V to 7 V. |
| 5 | ILIM | output | Connect a resistor (5 kΩ to 25 kΩ) from this pin to VBB to set the current-limit threshold; if left floating, the device uses the default internal current limit. |
| 6 | VOUT | output | Channel output to the load; internally clamped (VDS clamp 40 V min, 46 V typ) to limit FET voltage when switching off inductive loads. |
| 7 | VOUT | output | Channel output to the load; internally clamped (VDS clamp 40 V min, 46 V typ) to limit FET voltage when switching off inductive loads. |
| 8 | VOUT | output | Channel output to the load; internally clamped (VDS clamp 40 V min, 46 V typ) to limit FET voltage when switching off inductive loads. |
| 9 | VOUT | output | Channel output to the load; internally clamped (VDS clamp 40 V min, 46 V typ) to limit FET voltage when switching off inductive loads. |
| 10 | VOUT | output | Channel output to the load; internally clamped (VDS clamp 40 V min, 46 V typ) to limit FET voltage when switching off inductive loads. |
| 11 | VOUT | output | Channel output to the load; internally clamped (VDS clamp 40 V min, 46 V typ) to limit FET voltage when switching off inductive loads. |
| 12 | NC | unconnected | No connect; leave floating. |
| 13 | NC | unconnected | No connect; leave floating. |
| 14 | SEL1 | input | Diagnostics select that chooses device temperature sensing when high (no function on Version F); if unused it must be grounded through RPROT (15 kΩ typical) to enable automatic FET turn-on during reverse battery. |
| 15 | NC | unconnected | No connect; leave floating. |
| 16 | DIA_EN | input | Diagnostic enable, active high with VIL of 0.8 V maximum and VIH of 2.0 V minimum; when unused, the analog sense, open-load and short-to-battery diagnostics are unavailable. |
| 17 | VBB | power_in | Power supply input (exposed thermal pad) with 6 V to 18 V nominal range, 36 V maximum continuous and 40 V load-dump withstand. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | HTSSOP-16 |
| Category | Power Management (PMIC) |
| Pins | 17 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Maximum continuous supply voltage | VBB | 36 | V | 6 | |||
| Load dump voltage | VLD | 40 | V | ISO16750-2:2010(E) | 6 | ||
| Reverse battery voltage | VRev, t | -18 | V | t ≤ 3 minutes | 6 | ||
| Enable pin voltage | VEN | -1 | 7 | V | 6 | ||
| LATCH pin voltage | VLATCH | -1 | 7 | V | 6 | ||
| Diagnostic Enable pin voltage | VDIA_EN | -1 | 7 | V | 6 | ||
| Sense pin voltage | VSNS | -1 | 18 | V | 6 | ||
| Select pin voltage | VSEL | -1 | 7 | V | 6 | ||
| Reverse ground current | IGND | -50 | mA | VBB < 0V | 6 | ||
| Energy dissipation during turnoff, single pulse | ETOFF | 95 | mJ | Single pulse, LOUT = 5mH, TJ,start = 125°C | 6 | ||
| Energy dissipation during turnoff, repetitive pulse | ETOFF | 56 | mJ | Repetitive pulse, LOUT = 5mH, TJ,start = 125°C | 6 | ||
| Maximum junction temperature | TJ | 150 | °C | 6 | |||
| Storage temperature | Tstg | -65 | 150 | °C | 6 | ||
| VBB nominal supply voltage | VBB | 6 | 18 | V | 6 | ||
| VBB extended lower supply voltage | VBB | 3 | 6 | V | 6 | ||
| VBB extended higher supply voltage | VBB | 18 | 28 | V | 6 | ||
| Enable voltage | VEN | -1 | 5.5 | V | 6 | ||
| LATCH voltage | VLATCH | -1 | 5.5 | V | 6 | ||
| Diagnostic Enable voltage | VDIA_EN | -1 | 5.5 | V | 6 | ||
| Select voltage | VSEL1 | -1 | 5.5 | V | 6 | ||
| Sense voltage | VSNS | -1 | 7 | V | 6 | ||
| VBB undervoltage lockout falling | VUVLOF | 2 | 3 | V | Measured with respect to the GND pin of the device | 7 | |
| VBB undervoltage lockout rising | VUVLOR | 2.2 | 3 | V | Measured with respect to the GND pin of the device | 7 | |
| VDS clamp voltage | VDSCLAMP | 40 | 46 | V | 7 | ||
| VBB clamp voltage | VBBCLAMP | 58 | 76 | V | 7 | ||
| Standby current (total device leakage including MOSFET) | ISB | 0.1 | µA | VBB = 13.5V, TJ = 25°C, VEN = VDIA_EN = 0V, VOUT = 0V | 7 | ||
| Standby current (total device leakage including MOSFET) | ISB | 0.5 | µA | VBB = 13.5V, TJ = 85°C, VEN = VDIA_EN = 0V, VOUT = 0V | 7 | ||
| Output leakage current | IOUT(standby) | 0.01 | 0.5 | µA | VBB = 13.5V, TJ = 25°C, VEN = VDIA_EN = 0V, VOUT = 0V | 7 | |
| Output leakage current | IOUT(standby) | 3 | µA | VBB = 13.5V, TJ = 125°C, VEN = VDIA_EN = 0V, VOUT = 0V | 7 | ||
| Current consumption in diagnostic mode | IDIA | 3 | 6 | mA | VBB = 13.5V, ISNS = 0mA, VEN = 0V, VDIA_EN = 5V, VOUT = 0V | 7 | |
| Quiescent current | IQ | 3 | 6 | mA | VBB = 13.5V, VEN = VDIA_EN = 5V, IOUT = 0A | 7 | |
| Standby mode delay time | tSTBY | 12 | 17 | 22 | ms | VEN = VDIA_EN = 0V to standby | 7 |
| On-resistance (includes MOSFET and package) | RON | 8 | mΩ | TJ = 25°C, 6V ≤ VBB ≤ 28V | 7 | ||
| On-resistance (includes MOSFET and package) | RON | 16 | mΩ | TJ = 150°C, 6V ≤ VBB ≤ 28V | 7 | ||
| On-resistance (includes MOSFET and package) | RON | 12 | mΩ | TJ = 25°C, 3V ≤ VBB ≤ 6V | 7 | ||
| On-resistance during reverse polarity | RON(REV) | 8 | mΩ | TJ = 25°C, -18V ≤ VBB ≤ -8V | 7 | ||
| On-resistance during reverse polarity | RON(REV) | 16 | mΩ | TJ = 105°C, -18V ≤ VBB ≤ -8V | 7 | ||
| Current sense current accuracy | ISNSI | -5 | 5.3 | % | VEN = VDIA_EN = 5V, VSEL1 = 0V, IOUT = 10A | 8 | |
| Current sense current accuracy | ISNSI | -4.6 | 6.2 | % | VEN = VDIA_EN = 5V, VSEL1 = 0V, IOUT = 300mA | 8 | |
| Current sense current accuracy | ISNSI | -13.6 | 15.1 | % | VEN = VDIA_EN = 5V, VSEL1 = 0V, IOUT = 100mA | 8 | |
| Current sense current accuracy | ISNSI | -56 | 57.3 | % | VEN = VDIA_EN = 5V, VSEL1 = 0V, IOUT = 20mA | 8 | |
| Fault high-level current on SNS | ISNSFH | 4 | 4.5 | 5.3 | mA | VDIA_EN = 5V, VSEL1 = 0V | 8 |
| Short circuit maximum supply voltage (Version B) | VSC | 18 | V | Version B | 8 | ||
| Current limit threshold (Version B) | ICL | 47.1 | 70 | 84.2 | A | Device Version B, TJ = -40°C to 150°C, RILIM = 5kΩ | 8 |
| Current limit threshold (Version B) | ICL | 9.9 | 14 | 17.8 | A | Device Version B, TJ = -40°C to 150°C, RILIM = 25kΩ | 8 |
| Current limit ratio (Version B) | KCL | 245 | 350 | 437.5 | A * kΩ | Version B | 8 |
| Open-load (OL) detection voltage | VOL | 2 | 3 | 4 | V | VEN = 0V, VDIA_EN = 5V, VSEL1 = 0V | 8 |
| OL and STB indication time from EN falling | tOL1 | 300 | 500 | 700 | µs | VEN = 5V to 0V, VDIA_EN = 5V, VSEL1 = 0V, IOUT = 0mA, VOUT = 4V | 9 |
| Thermal shutdown | TABS | 150 | °C | 9 | |||
| Thermal shutdown hysteresis | THYS | 20 | 25 | 30 | °C | 9 | |
| Retry time | tRETRY | 1 | 2 | 3 | ms | Time from fault shutdown until switch re-enable (thermal shutdown or current limit) | 9 |
| EN input voltage low-level | VIL, EN | 0.8 | V | No GND network diode | 9 | ||
| EN input voltage high-level | VIH, EN | 2 | V | No GND network diode | 9 | ||
| Turnon delay time (from Active) | tDR | 20 | 60 | 100 | µs | VBB = 13.5V, RL = 2.6Ω, 50% EN rising to 10% VOUT rising | 10 |
| Turnoff delay time | tDF | 20 | 60 | 100 | µs | VBB = 13.5V, RL = 2.6Ω, 50% EN falling to 90% VOUT falling | 10 |
| Turnon time (active) | tON | 39 | 94 | 235 | µs | VBB = 13.5V, RL = 2.6Ω, 50% EN rising to 80% VOUT rising | 10 |
| Turnoff time | tOFF | 39 | 94 | 235 | µs | VBB = 13.5V, RL = 2.6Ω, 50% EN falling to 20% VOUT falling | 10 |
| VOUT rising slew rate | SRR | 0.1 | 0.4 | 0.7 | V/µs | VBB = 13.5V, 20% to 80% of VOUT, RL = 2.6Ω | 10 |
| Junction-to-ambient thermal resistance | RθJA | 32.6 | °C/W | 7 |
CAD (KiCad official)
- Symbol:
TPS1HB08BQPWPRQ1 - Footprint:
Package_SO:TSSOP-16-1EP_4.4x5mm_P0.65mm - 3D model: HTSSOP-16 (KiCad packages3D, STEP)
- 3D model files:
tps1hb08bqpwprq1-etched.step/tps1hb08bqpwprq1-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);tps1hb08bqpwprq1.step/tps1hb08bqpwprq1.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (54 pp, sha256
8f2664df02ed6b2e, retrieved 2026-11-10, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).