main
Ray
tpa3138d2pwpr: specified limits as data (metadata.characteristics, 59 rows from the datasheet)
cef61d3
TPA3138D2PWPR
Texas Instruments · Audio Amplifiers · TSSOP-28-EP
TPA3138D2PWPR from Texas Instruments, in a TSSOP-28-EP. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | NC | unconnected | No Connect Pin; can be shorted to PVCC, shorted to GND, or left open. |
| 2 | SD/FAULT | bidirectional | Shutdown control and fault reporting output with TTL logic compliance to AVCC; LOW disables outputs to Hi-Z and enters low-current shutdown state, HIGH enables normal operation and reports Over-Temp, Over-Current, DC Detect faults with auto-recovery. |
| 3 | LINP | input | Positive audio input for left channel, biased at 2.5 V; connect to GND for PBTL mode operation. |
| 4 | LINN | input | Negative audio input for left channel, biased at 2.5 V; connect to GND for PBTL mode operation. |
| 5 | GAIN_SEL | input | Gain select least significant bit with TTL logic compliance to AVDD; LOW sets 20 dB gain, HIGH sets 26 dB gain, floating defaults to 26 dB gain. |
| 6 | MODE_SEL | input | Mode select least significant bit with TTL logic compliance to AVDD; LOW sets BD Mode with 7.5 V UVP threshold, HIGH or floating sets 1SPW mode with 3.4 V UVP threshold. |
| 7 | AVCC | power_in | Analog power supply, 3.5 V to 14.4 V; add 1 μF decoupling capacitor to ground. |
| 8 | GND | power_in | Analog signal ground. |
| 9 | GVDD | power_out | FET gate drive supply output with nominal 5 V; add 1 μF capacitor to ground at this pin. |
| 10 | PLIMIT | input | Power limiter level control input; connect resistor divider from GVDD to GND to set power limit, or connect directly to GVDD for no power limiting. |
| 11 | RINN | input | Negative audio input for right channel, biased at 2.5 V. |
| 12 | RINP | input | Positive audio input for right channel, biased at 2.5 V. |
| 13 | NC | unconnected | No Connect Pin; can be shorted to PVCC, shorted to GND, or left open. |
| 14 | AGND | power_in | Analog signal ground; must be connected to the thermal pad for best thermal and electrical performance. |
| 15 | PVCCR | power_in | Power supply for right channel H-bridge, 3.5 V to 14.4 V; internally connected with left channel PVCC. |
| 16 | PVCCR | power_in | Power supply for right channel H-bridge, 3.5 V to 14.4 V; internally connected with left channel PVCC. |
| 17 | BSPR | power_in | Bootstrap supply for right channel positive high-side FET; connect 0.22 μF capacitor from OUTPR to BSPR. |
| 18 | OUTPR | output | Class-D H-bridge positive output for right channel. |
| 19 | GND | power_in | Power ground for the H-bridges. |
| 20 | OUTNR | output | Class-D H-bridge negative output for right channel. |
| 21 | BSNR | power_in | Bootstrap supply for right channel negative high-side FET; connect 0.22 μF capacitor from OUTNR to BSNR. |
| 22 | BSNL | power_in | Bootstrap supply for left channel negative high-side FET; connect 0.22 μF capacitor from OUTNL to BSNL. |
| 23 | OUTNL | output | Class-D H-bridge negative output for left channel. |
| 24 | GND | power_in | Power ground for the H-bridges. |
| 25 | OUTPL | output | Class-D H-bridge positive output for left channel. |
| 26 | BSPL | power_in | Bootstrap supply for left channel positive high-side FET; connect 0.22 μF capacitor from OUTPL to BSPL. |
| 27 | PVCCL | power_in | Power supply for left channel H-bridge, 3.5 V to 14.4 V; internally connected with right channel PVCC. |
| 28 | PVCCL | power_in | Power supply for left channel H-bridge, 3.5 V to 14.4 V; internally connected with right channel PVCC. |
| 29 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | TSSOP-28-EP |
| Category | Amplifiers/Comparators |
| Pins | 29 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage AVCC to GND, PVCC to GND | -0.3 | 20 | V | 5 | |||
| Input current, to any pin except supply pins | 10 | mA | 5 | ||||
| Interface pin voltage, SD/FAULT to GND, GAIN_SEL, MODE_SEL (printed max AVCC + 0.3 V) | -0.3 | V | 5 | ||||
| Voltage slew rate, SD/FAULT (footnote 2) | 10 | V/ms | 5 | ||||
| PLIMIT pin voltage (printed max GVDD + 0.3 V) | -0.3 | V | 5 | ||||
| RINN, RINP, LINN, LINP input voltage | -0.3 | 5.5 | V | 5 | |||
| Minimum load resistance, BTL | RL | 4.8 | Ω | 10 V < PVCC < 14.4 V | 5 | ||
| Minimum load resistance, BTL | RL | 3.2 | Ω | 3.5 V < PVCC < 10 V | 5 | ||
| Minimum load resistance, PBTL | RL | 2.4 | Ω | 10 V < PVCC < 14.4 V | 5 | ||
| Minimum load resistance, PBTL | RL | 1.6 | Ω | 3.5 V < PVCC < 10 V | 5 | ||
| Operating junction temperature range | TJ | -25 | 150 | °C | 5 | ||
| Storage temperature range | Tstg | -40 | 125 | °C | 5 | ||
| Supply voltage PVCC, AVCC | VCC | 3.5 | 14.4 | V | 6 | ||
| High-level input voltage (printed max AVCC) | VIH | 2 | V | SD/FAULT (1), GAIN_SEL, MODE_SEL | 6 | ||
| Low-level input voltage | VIL | 0.8 | V | SD/FAULT, GAIN_SEL, MODE_SEL (2) | 6 | ||
| Low-level output voltage | VOL | 0.8 | V | SD/FAULT, RPULL-UP = 100 kΩ, PVCC = 14.4 V | 6 | ||
| High-level input current | IIH | 50 | µA | SD/FAULT, GAIN_SEL, MODE_SEL, VI = 2 V, AVCC = 12 V | 6 | ||
| Low-level input current | IIL | 5 | µA | SD/FAULT, GAIN_SEL, MODE_SEL, VI = 0.8 V, AVCC = 12 V | 6 | ||
| Operating free-air temperature | TA | -10 | 85 | °C | 6 | ||
| Operating junction temperature | TJ | -10 | 150 | °C | 6 | ||
| Gain | G | 19 | 20 | 21 | dB | GAIN_SEL = 0.8 V | 7 |
| Gain | G | 25 | 26 | 27 | dB | GAIN_SEL = 2 V | 7 |
| Oscillator frequency, spread spectrum ON | fOSC, SS | 305 | 340 | kHz | Spread spectrum ON | 7 | |
| Gate drive supply | 4.8 | 5 | 5.2 | V | IGVDD = 2 mA | 7 | |
| Over-temperature trip point tolerance, device to device | -15 | 15 | °C | Device to device | 14 | ||
| Power supply ripple rejection | PSRR | -70 | dB | 200-mVPP ripple at 1 kHz, Gain = 26 dB, Inputs ac-coupled to GND | 7 | ||
| Continuous output power, BTL | PO | 10 | W | BTL, THD+N = 1%, f = 1 kHz, PVCC = 12 V, RL = 6 Ω | 7 | ||
| Continuous output power, BTL | PO | 12 | W | BTL, THD+N = 10%, f = 1 kHz, PVCC = 12 V, RL = 6 Ω | 7 | ||
| Continuous output power, BTL | PO | 8 | W | BTL, THD+N = 1%, f = 1 kHz, PVCC = 12 V, RL = 8 Ω | 7 | ||
| Continuous output power, BTL | PO | 9.9 | W | BTL, THD+N = 10%, f = 1 kHz, PVCC = 12 V, RL = 8 Ω | 7 | ||
| Continuous output power, PBTL (mono) | PO | 18.5 | W | PBTL, THD+N = 10%, f = 1 kHz, PVCC = 12 V, RL = 4 Ω | 7 | ||
| Maximum output current | IO | 3.5 | A | f = 1 kHz, RL = 3 Ω | 7 | ||
| Total harmonic distortion + noise | THD+N | 0.04 | % | f = 1 kHz, PO = 5 W (half-power) | 7 | ||
| Output integrated noise | Vn | 85 | µV | 20 Hz to 22 kHz, A-weighted filter, Gain = 26 dB | 7 | ||
| Output integrated noise | Vn | -81 | dBV | 20 Hz to 22 kHz, A-weighted filter, Gain = 26 dB | 7 | ||
| Output integrated noise | Vn | 72 | µV | 20 Hz to 22 kHz, A-weighted filter, Gain = 20 dB | 7 | ||
| Output integrated noise | Vn | -82.6 | dBV | 20 Hz to 22 kHz, A-weighted filter, Gain = 20 dB | 7 | ||
| Crosstalk | -95 | dB | VO = 1 Vrms, Gain = 26 dB, f = 1 kHz | 7 | |||
| Signal-to-noise ratio | SNR | 102 | dB | Maximum output at THD+N < 1%, f = 1 kHz, Gain = 26 dB, A-weighted | 7 | ||
| Thermal trip point | OTE | 150 | °C | 7 | |||
| Thermal hysteresis | 15 | °C | 7 | ||||
| Output offset voltage (measured differentially) | /VOS/ | 1.5 | mV | VI = 0 V, Gain = 26 dB | 7 | ||
| Quiescent supply current, 1SPW mode | ICC | 20 | mA | SD/FAULT = 2 V, 10 µF + 680 nF output filter, 1SPW Mode, PVCC = 12 V | 7 | ||
| Quiescent supply current, BD mode | ICC | 37 | mA | SD/FAULT = 2 V, 10 µF + 680 nF output filter, BD Mode, PVCC = 12 V | 7 | ||
| Quiescent supply current in shutdown mode | ICC(SD) | 10 | µA | SD/FAULT = 0.8 V, no load | 7 | ||
| Drain-source on-state resistance, high side | rDS(on) | 180 | mΩ | IO = 500 mA, TJ = 25°C, excluding metal and bond wire resistance | 7 | ||
| Drain-source on-state resistance, low side | rDS(on) | 180 | mΩ | IO = 500 mA, TJ = 25°C, excluding metal and bond wire resistance | 7 | ||
| Turn-on time | tON | 50 | ms | SD/FAULT = 2 V | 7 | ||
| Turn-off time | tOFF | 2.9 | µs | SD/FAULT = 0.8 V | 7 | ||
| DC detect time | tDCDET | 800 | ms | VRINP = 2.6 V and VRINN = 2.4 V, or VRINP = 2.4 V and VRINN = 2.6 V | 7 | ||
| Over voltage protection | OVP | 15.8 | V | 7 | |||
| Under voltage protection, BD mode | UVP | 7.5 | V | MODE_SEL = 0.8 V (BD mode) | 7 | ||
| Under voltage protection, 1SPW mode | UVP | 3.4 | V | MODE_SEL = 2 V, or floating (1SPW mode) | 7 | ||
| Junction-to-ambient thermal resistance | RθJA | 30.3 | °C/W | PWP (HTSSOP) 28 pins | 6 | ||
| Junction-to-case (top) thermal resistance | RθJC(top) | 33.5 | °C/W | PWP (HTSSOP) 28 pins | 6 | ||
| Junction-to-board thermal resistance | RθJB | 17.5 | °C/W | PWP (HTSSOP) 28 pins | 6 | ||
| Junction-to-top characterization parameter | ψJT | 0.9 | °C/W | PWP (HTSSOP) 28 pins | 6 | ||
| Junction-to-board characterization parameter | ψJB | 7.2 | °C/W | PWP (HTSSOP) 28 pins | 6 | ||
| Junction-to-case (bottom) thermal resistance | RθJC(bot) | 0.9 | °C/W | PWP (HTSSOP) 28 pins | 6 |
CAD (KiCad official)
- Symbol:
TPA3138D2PWPR - Footprint:
Package_SO:TSSOP-28-1EP_4.4x9.7mm_P0.65mm_EP2.85x6.7mm - 3D model: TSSOP-28-EP (KiCad packages3D, STEP)
- 3D model files:
tpa3138d2pwpr-etched.step/tpa3138d2pwpr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);tpa3138d2pwpr.step/tpa3138d2pwpr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (37 pp, sha256
281fbddb49687ce9, retrieved 2026-09-23, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.2, primaryclaude-haiku-4-5-20251001(text), consensusclaude-sonnet-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# TPA3138D2PWPR
**Texas Instruments** · Audio Amplifiers · TSSOP-28-EP
TPA3138D2PWPR from Texas Instruments, in a TSSOP-28-EP. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | NC | unconnected | No Connect Pin; can be shorted to PVCC, shorted to GND, or left open. |
| 2 | SD/FAULT | bidirectional | Shutdown control and fault reporting output with TTL logic compliance to AVCC; LOW disables outputs to Hi-Z and enters low-current shutdown state, HIGH enables normal operation and reports Over-Temp, Over-Current, DC Detect faults with auto-recovery. |
| 3 | LINP | input | Positive audio input for left channel, biased at 2.5 V; connect to GND for PBTL mode operation. |
| 4 | LINN | input | Negative audio input for left channel, biased at 2.5 V; connect to GND for PBTL mode operation. |
| 5 | GAIN_SEL | input | Gain select least significant bit with TTL logic compliance to AVDD; LOW sets 20 dB gain, HIGH sets 26 dB gain, floating defaults to 26 dB gain. |
| 6 | MODE_SEL | input | Mode select least significant bit with TTL logic compliance to AVDD; LOW sets BD Mode with 7.5 V UVP threshold, HIGH or floating sets 1SPW mode with 3.4 V UVP threshold. |
| 7 | AVCC | power_in | Analog power supply, 3.5 V to 14.4 V; add 1 μF decoupling capacitor to ground. |
| 8 | GND | power_in | Analog signal ground. |
| 9 | GVDD | power_out | FET gate drive supply output with nominal 5 V; add 1 μF capacitor to ground at this pin. |
| 10 | PLIMIT | input | Power limiter level control input; connect resistor divider from GVDD to GND to set power limit, or connect directly to GVDD for no power limiting. |
| 11 | RINN | input | Negative audio input for right channel, biased at 2.5 V. |
| 12 | RINP | input | Positive audio input for right channel, biased at 2.5 V. |
| 13 | NC | unconnected | No Connect Pin; can be shorted to PVCC, shorted to GND, or left open. |
| 14 | AGND | power_in | Analog signal ground; must be connected to the thermal pad for best thermal and electrical performance. |
| 15 | PVCCR | power_in | Power supply for right channel H-bridge, 3.5 V to 14.4 V; internally connected with left channel PVCC. |
| 16 | PVCCR | power_in | Power supply for right channel H-bridge, 3.5 V to 14.4 V; internally connected with left channel PVCC. |
| 17 | BSPR | power_in | Bootstrap supply for right channel positive high-side FET; connect 0.22 μF capacitor from OUTPR to BSPR. |
| 18 | OUTPR | output | Class-D H-bridge positive output for right channel. |
| 19 | GND | power_in | Power ground for the H-bridges. |
| 20 | OUTNR | output | Class-D H-bridge negative output for right channel. |
| 21 | BSNR | power_in | Bootstrap supply for right channel negative high-side FET; connect 0.22 μF capacitor from OUTNR to BSNR. |
| 22 | BSNL | power_in | Bootstrap supply for left channel negative high-side FET; connect 0.22 μF capacitor from OUTNL to BSNL. |
| 23 | OUTNL | output | Class-D H-bridge negative output for left channel. |
| 24 | GND | power_in | Power ground for the H-bridges. |
| 25 | OUTPL | output | Class-D H-bridge positive output for left channel. |
| 26 | BSPL | power_in | Bootstrap supply for left channel positive high-side FET; connect 0.22 μF capacitor from OUTPL to BSPL. |
| 27 | PVCCL | power_in | Power supply for left channel H-bridge, 3.5 V to 14.4 V; internally connected with right channel PVCC. |
| 28 | PVCCL | power_in | Power supply for left channel H-bridge, 3.5 V to 14.4 V; internally connected with right channel PVCC. |
| 29 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | TSSOP-28-EP |
| Category | Amplifiers/Comparators |
| Pins | 29 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage AVCC to GND, PVCC to GND | | -0.3 | | 20 | V | | 5 |
| Input current, to any pin except supply pins | | | | 10 | mA | | 5 |
| Interface pin voltage, SD/FAULT to GND, GAIN_SEL, MODE_SEL (printed max AVCC + 0.3 V) | | -0.3 | | | V | | 5 |
| Voltage slew rate, SD/FAULT (footnote 2) | | | | 10 | V/ms | | 5 |
| PLIMIT pin voltage (printed max GVDD + 0.3 V) | | -0.3 | | | V | | 5 |
| RINN, RINP, LINN, LINP input voltage | | -0.3 | | 5.5 | V | | 5 |
| Minimum load resistance, BTL | RL | 4.8 | | | Ω | 10 V < PVCC < 14.4 V | 5 |
| Minimum load resistance, BTL | RL | 3.2 | | | Ω | 3.5 V < PVCC < 10 V | 5 |
| Minimum load resistance, PBTL | RL | 2.4 | | | Ω | 10 V < PVCC < 14.4 V | 5 |
| Minimum load resistance, PBTL | RL | 1.6 | | | Ω | 3.5 V < PVCC < 10 V | 5 |
| Operating junction temperature range | TJ | -25 | | 150 | °C | | 5 |
| Storage temperature range | Tstg | -40 | | 125 | °C | | 5 |
| Supply voltage PVCC, AVCC | VCC | 3.5 | | 14.4 | V | | 6 |
| High-level input voltage (printed max AVCC) | VIH | 2 | | | V | SD/FAULT (1), GAIN_SEL, MODE_SEL | 6 |
| Low-level input voltage | VIL | | | 0.8 | V | SD/FAULT, GAIN_SEL, MODE_SEL (2) | 6 |
| Low-level output voltage | VOL | | | 0.8 | V | SD/FAULT, RPULL-UP = 100 kΩ, PVCC = 14.4 V | 6 |
| High-level input current | IIH | | | 50 | µA | SD/FAULT, GAIN_SEL, MODE_SEL, VI = 2 V, AVCC = 12 V | 6 |
| Low-level input current | IIL | | | 5 | µA | SD/FAULT, GAIN_SEL, MODE_SEL, VI = 0.8 V, AVCC = 12 V | 6 |
| Operating free-air temperature | TA | -10 | | 85 | °C | | 6 |
| Operating junction temperature | TJ | -10 | | 150 | °C | | 6 |
| Gain | G | 19 | 20 | 21 | dB | GAIN_SEL = 0.8 V | 7 |
| Gain | G | 25 | 26 | 27 | dB | GAIN_SEL = 2 V | 7 |
| Oscillator frequency, spread spectrum ON | fOSC, SS | 305 | | 340 | kHz | Spread spectrum ON | 7 |
| Gate drive supply | | 4.8 | 5 | 5.2 | V | IGVDD = 2 mA | 7 |
| Over-temperature trip point tolerance, device to device | | -15 | | 15 | °C | Device to device | 14 |
| Power supply ripple rejection | PSRR | | -70 | | dB | 200-mVPP ripple at 1 kHz, Gain = 26 dB, Inputs ac-coupled to GND | 7 |
| Continuous output power, BTL | PO | | 10 | | W | BTL, THD+N = 1%, f = 1 kHz, PVCC = 12 V, RL = 6 Ω | 7 |
| Continuous output power, BTL | PO | | 12 | | W | BTL, THD+N = 10%, f = 1 kHz, PVCC = 12 V, RL = 6 Ω | 7 |
| Continuous output power, BTL | PO | | 8 | | W | BTL, THD+N = 1%, f = 1 kHz, PVCC = 12 V, RL = 8 Ω | 7 |
| Continuous output power, BTL | PO | | 9.9 | | W | BTL, THD+N = 10%, f = 1 kHz, PVCC = 12 V, RL = 8 Ω | 7 |
| Continuous output power, PBTL (mono) | PO | | 18.5 | | W | PBTL, THD+N = 10%, f = 1 kHz, PVCC = 12 V, RL = 4 Ω | 7 |
| Maximum output current | IO | | 3.5 | | A | f = 1 kHz, RL = 3 Ω | 7 |
| Total harmonic distortion + noise | THD+N | | 0.04 | | % | f = 1 kHz, PO = 5 W (half-power) | 7 |
| Output integrated noise | Vn | | 85 | | µV | 20 Hz to 22 kHz, A-weighted filter, Gain = 26 dB | 7 |
| Output integrated noise | Vn | | -81 | | dBV | 20 Hz to 22 kHz, A-weighted filter, Gain = 26 dB | 7 |
| Output integrated noise | Vn | | 72 | | µV | 20 Hz to 22 kHz, A-weighted filter, Gain = 20 dB | 7 |
| Output integrated noise | Vn | | -82.6 | | dBV | 20 Hz to 22 kHz, A-weighted filter, Gain = 20 dB | 7 |
| Crosstalk | | | -95 | | dB | VO = 1 Vrms, Gain = 26 dB, f = 1 kHz | 7 |
| Signal-to-noise ratio | SNR | | 102 | | dB | Maximum output at THD+N < 1%, f = 1 kHz, Gain = 26 dB, A-weighted | 7 |
| Thermal trip point | OTE | | 150 | | °C | | 7 |
| Thermal hysteresis | | | 15 | | °C | | 7 |
| Output offset voltage (measured differentially) | /VOS/ | | 1.5 | | mV | VI = 0 V, Gain = 26 dB | 7 |
| Quiescent supply current, 1SPW mode | ICC | | 20 | | mA | SD/FAULT = 2 V, 10 µF + 680 nF output filter, 1SPW Mode, PVCC = 12 V | 7 |
| Quiescent supply current, BD mode | ICC | | 37 | | mA | SD/FAULT = 2 V, 10 µF + 680 nF output filter, BD Mode, PVCC = 12 V | 7 |
| Quiescent supply current in shutdown mode | ICC(SD) | | 10 | | µA | SD/FAULT = 0.8 V, no load | 7 |
| Drain-source on-state resistance, high side | rDS(on) | | 180 | | mΩ | IO = 500 mA, TJ = 25°C, excluding metal and bond wire resistance | 7 |
| Drain-source on-state resistance, low side | rDS(on) | | 180 | | mΩ | IO = 500 mA, TJ = 25°C, excluding metal and bond wire resistance | 7 |
| Turn-on time | tON | | 50 | | ms | SD/FAULT = 2 V | 7 |
| Turn-off time | tOFF | | 2.9 | | µs | SD/FAULT = 0.8 V | 7 |
| DC detect time | tDCDET | | 800 | | ms | VRINP = 2.6 V and VRINN = 2.4 V, or VRINP = 2.4 V and VRINN = 2.6 V | 7 |
| Over voltage protection | OVP | | 15.8 | | V | | 7 |
| Under voltage protection, BD mode | UVP | | 7.5 | | V | MODE_SEL = 0.8 V (BD mode) | 7 |
| Under voltage protection, 1SPW mode | UVP | | 3.4 | | V | MODE_SEL = 2 V, or floating (1SPW mode) | 7 |
| Junction-to-ambient thermal resistance | RθJA | | 30.3 | | °C/W | PWP (HTSSOP) 28 pins | 6 |
| Junction-to-case (top) thermal resistance | RθJC(top) | | 33.5 | | °C/W | PWP (HTSSOP) 28 pins | 6 |
| Junction-to-board thermal resistance | RθJB | | 17.5 | | °C/W | PWP (HTSSOP) 28 pins | 6 |
| Junction-to-top characterization parameter | ψJT | | 0.9 | | °C/W | PWP (HTSSOP) 28 pins | 6 |
| Junction-to-board characterization parameter | ψJB | | 7.2 | | °C/W | PWP (HTSSOP) 28 pins | 6 |
| Junction-to-case (bottom) thermal resistance | RθJC(bot) | | 0.9 | | °C/W | PWP (HTSSOP) 28 pins | 6 |
## CAD (KiCad official)
- Symbol: `TPA3138D2PWPR`
- Footprint: `Package_SO:TSSOP-28-1EP_4.4x9.7mm_P0.65mm_EP2.85x6.7mm`
- 3D model: TSSOP-28-EP (KiCad packages3D, STEP)
- 3D model files: `tpa3138d2pwpr-etched.step` / `tpa3138d2pwpr-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `tpa3138d2pwpr.step` / `tpa3138d2pwpr.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/tpa3138d2) (37 pp, sha256 `281fbddb49687ce9`, retrieved 2026-09-23, tier: lcsc)
- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.2`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/tpa3138d2pwpr-datasheet.pdf)