main
Ray
Publish 0.1.0
059ec60
TLV75201PDSQT
Texas Instruments · Linear Voltage Regulators (LDO) · WSON-10-EP(2x2)
TLV75201PDSQT from Texas Instruments, in a WSON-10-EP(2x2). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | FB1 | input | Input to the channel 1 control loop error amplifier, used with an external resistor divider to set the channel 1 output voltage (0.55 V to 5.5 V range). |
| 2 | GND | power_in | Ground pin. |
| 3 | EN1 | input | Channel 1 enable pin; drive greater than VEN1(HI) to turn on the regulator and less than VEN1(LO) to put the LDO into shutdown mode. |
| 4 | GND | power_in | Ground pin. |
| 5 | EN2 | input | Channel 2 enable pin; drive greater than VEN1(HI) to turn on the regulator and less than VEN2(LO) to put the LDO into shutdown mode. |
| 6 | IN2 | power_in | Channel 2 input supply (1.5 V to 6.0 V); use at least the recommended 1 µF ceramic capacitor to ground placed close to the device. |
| 7 | FB2 | input | Input to the channel 2 control loop error amplifier, used with an external resistor divider to set the channel 2 output voltage (0.55 V to 5.5 V range). |
| 8 | OUT2 | power_out | Channel 2 regulated output pin; a capacitor to ground is required for stability (recommended 1 µF to 220 µF, minimum derated 0.47 µF). |
| 9 | IN1 | power_in | Channel 1 input supply (1.5 V to 6.0 V); use at least the recommended 1 µF ceramic capacitor to ground placed close to the device. |
| 10 | OUT1 | power_out | Channel 1 regulated output pin; a capacitor to ground is required for stability (recommended 1 µF to 220 µF, minimum derated 0.47 µF). |
| 11 | Thermal Pad | passive | Thermal pad; connect to a large area GND plane for improved thermal performance. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | WSON-10-EP(2x2) |
| Category | Power Supply Chip |
| Pins | 11 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage | VIN | -0.3 | 6.5 | V | 4 | ||
| Enable voltage | VEN | -0.3 | 6.5 | V | 4 | ||
| Feedback voltage | VFB | -0.3 | 2 | V | 4 | ||
| Output voltage | VOUT | -0.3 | 6.3 | V | VIN + 0.3 V or 6.0 V, whichever is smaller | 4 | |
| Operating junction temperature | TJ | -40 | 150 | °C | 4 | ||
| Storage temperature | Tstg | -65 | 150 | °C | 4 | ||
| ESD HBM | V(ESD) | -2000 | 2000 | V | Human-body model, ANSI/ESDA/JEDEC JS-001 | 4 | |
| ESD CDM | V(ESD) | -500 | 500 | V | Charged-device model, JESD22-C101 | 4 | |
| Input voltage | VIN | 1.5 | 6 | V | 4 | ||
| Output voltage | VOUT | 0.55 | 5.5 | V | 4 | ||
| Output current | IOUT | 0 | 1 | A | 4 | ||
| Input capacitor | CIN | 1 | μF | 4 | |||
| Output capacitor | COUT | 1 | 220 | μF | Minimum derated capacitance of 0.47 μF required for stability | 4 | |
| Enable voltage | VEN | 0 | 6 | V | 4 | ||
| Enable toggle frequency | fEN | 10 | kHz | 4 | |||
| Junction temperature | TJ | -40 | 125 | °C | 4 | ||
| Junction-to-ambient thermal resistance | RθJA | 74.6 | °C/W | DSQ (WSON) 10 pins | 4 | ||
| Junction-to-case (top) thermal resistance | RθJC(top) | 90.5 | °C/W | 4 | |||
| Junction-to-board thermal resistance | RθJB | 39.7 | °C/W | 4 | |||
| Junction-to-top characterization parameter | ψJT | 3.8 | °C/W | 4 | |||
| Junction-to-board characterization parameter | ψJB | 39.7 | °C/W | 4 | |||
| Junction-to-case (bottom) thermal resistance | RθJC(bot) | 17 | °C/W | 4 | |||
| Output accuracy | -0.5 | 0.5 | % | TJ = 25°C | 5 | ||
| Output accuracy over temperature | -1.5 | 1.5 | % | -40°C ≤ TJ ≤ +125°C; VOUT(NOM) + 0.5 V ≤ VIN ≤ 6.0 V | 5 | ||
| Feedback voltage | VFBx | 0.55 | V | TJ = 25°C | 5 | ||
| Line regulation | 2 | mV | VOUT(NOM) + 0.5 V ≤ VIN ≤ 6.0 V | 5 | |||
| Load regulation | 0.03 | V/A | 0.1 mA ≤ IOUT ≤ 1 A, VIN = VOUT + 0.5 V | 5 | |||
| Ground current | IGND | 10 | 25 | 31 | µA | IOUT = 0 mA, TJ = 25°C | 5 |
| Ground current over temperature | IGND | 35 | µA | IOUT = 0 mA, -40°C ≤ TJ ≤ +125°C | 5 | ||
| Shutdown current | ISHDN | 0.1 | 1 | µA | VEN ≤ 0.3 V, 1.5 V ≤ VIN ≤ 6.0 V | 5 | |
| Feedback pin current | IFB | 0.01 | 0.1 | µA | 5 | ||
| Output current limit | ICL | 1.22 | 1.54 | 1.83 | A | VOUT = 0.9 x VOUT(NOM), VOUT ≥ 1.5 V | 5 |
| Short-circuit current limit | ISC | 670 | 850 | mA | VOUT = 0 V | 5 | |
| Dropout voltage 0.65 V ≤ VOUT < 0.8 V | VDO | 896 | 1050 | mV | IOUT = 1 A, VOUT = 0.95 × VOUT(NOM) | 5 | |
| Dropout voltage 0.8 V ≤ VOUT < 0.9 V | VDO | 765 | 920 | mV | IOUT = 1 A, VOUT = 0.95 × VOUT(NOM) | 5 | |
| Dropout voltage 0.9 V ≤ VOUT < 1.0 V | VDO | 700 | 850 | mV | IOUT = 1 A, VOUT = 0.95 × VOUT(NOM) | 5 | |
| Dropout voltage 1.0 V ≤ VOUT < 1.2 V | VDO | 600 | 750 | mV | IOUT = 1 A, VOUT = 0.95 × VOUT(NOM) | 5 | |
| Dropout voltage 1.2 V ≤ VOUT < 1.5 V | VDO | 464 | 585 | mV | IOUT = 1 A, VOUT = 0.95 × VOUT(NOM) | 5 | |
| Dropout voltage 1.5 V ≤ VOUT < 1.8 V | VDO | 332 | 440 | mV | IOUT = 1 A, VOUT = 0.95 × VOUT(NOM) | 5 | |
| Dropout voltage 1.8 V ≤ VOUT < 2.5 V | VDO | 264 | 360 | mV | IOUT = 1 A, VOUT = 0.95 × VOUT(NOM) | 5 | |
| Dropout voltage 2.5 V ≤ VOUT < 3.3 V | VDO | 193 | 270 | mV | IOUT = 1 A, VOUT = 0.95 × VOUT(NOM) | 5 | |
| Dropout voltage 3.3 V ≤ VOUT ≤ 5.5 V | VDO | 161 | 225 | mV | IOUT = 1 A, VOUT = 0.95 × VOUT(NOM) | 5 | |
| UVLO rising | VUVLO | 1.21 | 1.33 | 1.47 | V | VIN rising | 5 |
| UVLO falling | VUVLO | 1.17 | 1.29 | 1.42 | V | VIN falling | 5 |
| UVLO hysteresis | VUVLO,HYST | 45 | mV | VIN hysteresis | 5 | ||
| Startup time | tSTR | 500 | 700 | µs | From EN low-to-high transition to VOUT = VOUT(NOM) x 95% | 5 | |
| EN pin high voltage | VENx(HI) | 1 | V | 5 | |||
| EN pin low voltage | VENx(LO) | 0.3 | V | 5 | |||
| Enable pin current | IENx | 10 | nA | VIN = VEN = 6.0 V | 5 | ||
| Pulldown resistance | RPULLDOWN | 95 | Ω | VIN = 6.0 V | 5 | ||
| PSRR | PSRR | 50 | dB | VIN = VOUT(NOM) + 1 V, IOUT = 50 mA, f = 1 kHz | 5 | ||
| Output noise voltage | Vn | 53 | µVRMS | BW = 10 Hz to 100 kHz, VOUT = 0.9 V | 5 | ||
| Thermal shutdown | TSD | 170 | °C | Shutdown, temperature increasing | 5 |
CAD (KiCad official)
- Symbol:
TLV75201PDSQT - Footprint:
Package_DFN_QFN:Texas_DSQ0010A_WSON-10-1EP_2x2mm_P0.4mm_EP0.9x1.5mm - 3D model: WSON-10-EP(2x2) (KiCad packages3D, STEP)
- 3D model files:
tlv75201pdsqt-etched.step/tlv75201pdsqt-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);tlv75201pdsqt.step/tlv75201pdsqt.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (31 pp, sha256
51fb9203a23738df, retrieved 2026-10-26, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# TLV75201PDSQT
**Texas Instruments** · Linear Voltage Regulators (LDO) · WSON-10-EP(2x2)
TLV75201PDSQT from Texas Instruments, in a WSON-10-EP(2x2). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | FB1 | input | Input to the channel 1 control loop error amplifier, used with an external resistor divider to set the channel 1 output voltage (0.55 V to 5.5 V range). |
| 2 | GND | power_in | Ground pin. |
| 3 | EN1 | input | Channel 1 enable pin; drive greater than VEN1(HI) to turn on the regulator and less than VEN1(LO) to put the LDO into shutdown mode. |
| 4 | GND | power_in | Ground pin. |
| 5 | EN2 | input | Channel 2 enable pin; drive greater than VEN1(HI) to turn on the regulator and less than VEN2(LO) to put the LDO into shutdown mode. |
| 6 | IN2 | power_in | Channel 2 input supply (1.5 V to 6.0 V); use at least the recommended 1 µF ceramic capacitor to ground placed close to the device. |
| 7 | FB2 | input | Input to the channel 2 control loop error amplifier, used with an external resistor divider to set the channel 2 output voltage (0.55 V to 5.5 V range). |
| 8 | OUT2 | power_out | Channel 2 regulated output pin; a capacitor to ground is required for stability (recommended 1 µF to 220 µF, minimum derated 0.47 µF). |
| 9 | IN1 | power_in | Channel 1 input supply (1.5 V to 6.0 V); use at least the recommended 1 µF ceramic capacitor to ground placed close to the device. |
| 10 | OUT1 | power_out | Channel 1 regulated output pin; a capacitor to ground is required for stability (recommended 1 µF to 220 µF, minimum derated 0.47 µF). |
| 11 | Thermal Pad | passive | Thermal pad; connect to a large area GND plane for improved thermal performance. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | WSON-10-EP(2x2) |
| Category | Power Supply Chip |
| Pins | 11 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage | VIN | -0.3 | | 6.5 | V | | 4 |
| Enable voltage | VEN | -0.3 | | 6.5 | V | | 4 |
| Feedback voltage | VFB | -0.3 | | 2 | V | | 4 |
| Output voltage | VOUT | -0.3 | | 6.3 | V | VIN + 0.3 V or 6.0 V, whichever is smaller | 4 |
| Operating junction temperature | TJ | -40 | | 150 | °C | | 4 |
| Storage temperature | Tstg | -65 | | 150 | °C | | 4 |
| ESD HBM | V(ESD) | -2000 | | 2000 | V | Human-body model, ANSI/ESDA/JEDEC JS-001 | 4 |
| ESD CDM | V(ESD) | -500 | | 500 | V | Charged-device model, JESD22-C101 | 4 |
| Input voltage | VIN | 1.5 | | 6 | V | | 4 |
| Output voltage | VOUT | 0.55 | | 5.5 | V | | 4 |
| Output current | IOUT | 0 | | 1 | A | | 4 |
| Input capacitor | CIN | | 1 | | μF | | 4 |
| Output capacitor | COUT | 1 | | 220 | μF | Minimum derated capacitance of 0.47 μF required for stability | 4 |
| Enable voltage | VEN | 0 | | 6 | V | | 4 |
| Enable toggle frequency | fEN | | | 10 | kHz | | 4 |
| Junction temperature | TJ | -40 | | 125 | °C | | 4 |
| Junction-to-ambient thermal resistance | RθJA | | 74.6 | | °C/W | DSQ (WSON) 10 pins | 4 |
| Junction-to-case (top) thermal resistance | RθJC(top) | | 90.5 | | °C/W | | 4 |
| Junction-to-board thermal resistance | RθJB | | 39.7 | | °C/W | | 4 |
| Junction-to-top characterization parameter | ψJT | | 3.8 | | °C/W | | 4 |
| Junction-to-board characterization parameter | ψJB | | 39.7 | | °C/W | | 4 |
| Junction-to-case (bottom) thermal resistance | RθJC(bot) | | 17 | | °C/W | | 4 |
| Output accuracy | | -0.5 | | 0.5 | % | TJ = 25°C | 5 |
| Output accuracy over temperature | | -1.5 | | 1.5 | % | -40°C ≤ TJ ≤ +125°C; VOUT(NOM) + 0.5 V ≤ VIN ≤ 6.0 V | 5 |
| Feedback voltage | VFBx | | 0.55 | | V | TJ = 25°C | 5 |
| Line regulation | | | 2 | | mV | VOUT(NOM) + 0.5 V ≤ VIN ≤ 6.0 V | 5 |
| Load regulation | | | 0.03 | | V/A | 0.1 mA ≤ IOUT ≤ 1 A, VIN = VOUT + 0.5 V | 5 |
| Ground current | IGND | 10 | 25 | 31 | µA | IOUT = 0 mA, TJ = 25°C | 5 |
| Ground current over temperature | IGND | | | 35 | µA | IOUT = 0 mA, -40°C ≤ TJ ≤ +125°C | 5 |
| Shutdown current | ISHDN | | 0.1 | 1 | µA | VEN ≤ 0.3 V, 1.5 V ≤ VIN ≤ 6.0 V | 5 |
| Feedback pin current | IFB | | 0.01 | 0.1 | µA | | 5 |
| Output current limit | ICL | 1.22 | 1.54 | 1.83 | A | VOUT = 0.9 x VOUT(NOM), VOUT ≥ 1.5 V | 5 |
| Short-circuit current limit | ISC | | 670 | 850 | mA | VOUT = 0 V | 5 |
| Dropout voltage 0.65 V ≤ VOUT < 0.8 V | VDO | | 896 | 1050 | mV | IOUT = 1 A, VOUT = 0.95 × VOUT(NOM) | 5 |
| Dropout voltage 0.8 V ≤ VOUT < 0.9 V | VDO | | 765 | 920 | mV | IOUT = 1 A, VOUT = 0.95 × VOUT(NOM) | 5 |
| Dropout voltage 0.9 V ≤ VOUT < 1.0 V | VDO | | 700 | 850 | mV | IOUT = 1 A, VOUT = 0.95 × VOUT(NOM) | 5 |
| Dropout voltage 1.0 V ≤ VOUT < 1.2 V | VDO | | 600 | 750 | mV | IOUT = 1 A, VOUT = 0.95 × VOUT(NOM) | 5 |
| Dropout voltage 1.2 V ≤ VOUT < 1.5 V | VDO | | 464 | 585 | mV | IOUT = 1 A, VOUT = 0.95 × VOUT(NOM) | 5 |
| Dropout voltage 1.5 V ≤ VOUT < 1.8 V | VDO | | 332 | 440 | mV | IOUT = 1 A, VOUT = 0.95 × VOUT(NOM) | 5 |
| Dropout voltage 1.8 V ≤ VOUT < 2.5 V | VDO | | 264 | 360 | mV | IOUT = 1 A, VOUT = 0.95 × VOUT(NOM) | 5 |
| Dropout voltage 2.5 V ≤ VOUT < 3.3 V | VDO | | 193 | 270 | mV | IOUT = 1 A, VOUT = 0.95 × VOUT(NOM) | 5 |
| Dropout voltage 3.3 V ≤ VOUT ≤ 5.5 V | VDO | | 161 | 225 | mV | IOUT = 1 A, VOUT = 0.95 × VOUT(NOM) | 5 |
| UVLO rising | VUVLO | 1.21 | 1.33 | 1.47 | V | VIN rising | 5 |
| UVLO falling | VUVLO | 1.17 | 1.29 | 1.42 | V | VIN falling | 5 |
| UVLO hysteresis | VUVLO,HYST | | 45 | | mV | VIN hysteresis | 5 |
| Startup time | tSTR | | 500 | 700 | µs | From EN low-to-high transition to VOUT = VOUT(NOM) x 95% | 5 |
| EN pin high voltage | VENx(HI) | | | 1 | V | | 5 |
| EN pin low voltage | VENx(LO) | 0.3 | | | V | | 5 |
| Enable pin current | IENx | | | 10 | nA | VIN = VEN = 6.0 V | 5 |
| Pulldown resistance | RPULLDOWN | | 95 | | Ω | VIN = 6.0 V | 5 |
| PSRR | PSRR | | 50 | | dB | VIN = VOUT(NOM) + 1 V, IOUT = 50 mA, f = 1 kHz | 5 |
| Output noise voltage | Vn | | 53 | | µVRMS | BW = 10 Hz to 100 kHz, VOUT = 0.9 V | 5 |
| Thermal shutdown | TSD | | 170 | | °C | Shutdown, temperature increasing | 5 |
## CAD (KiCad official)
- Symbol: `TLV75201PDSQT`
- Footprint: `Package_DFN_QFN:Texas_DSQ0010A_WSON-10-1EP_2x2mm_P0.4mm_EP0.9x1.5mm`
- 3D model: WSON-10-EP(2x2) (KiCad packages3D, STEP)
- 3D model files: `tlv75201pdsqt-etched.step` / `tlv75201pdsqt-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `tlv75201pdsqt.step` / `tlv75201pdsqt.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/tlv752) (31 pp, sha256 `51fb9203a23738df`, retrieved 2026-10-26, tier: lcsc)
- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-sonnet-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/tlv75201pdsqt-datasheet.pdf)