3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownTLIN1027DRBRQ1
Texas Instruments · LIN Transceivers · SON-8-EP(3x3)
TLIN1027DRBRQ1 from Texas Instruments, in a SON-8-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | RXD | output | Open-drain RXD output interface reporting the state of the LIN bus voltage. |
| 2 | EN | input | Enable input: high puts the device in normal operation mode and low puts the device in sleep mode. |
| 3 | NC | unconnected | Not connected. |
| 4 | TXD | input | TXD input interface controls the state of the LIN output and is internally pulled to ground. |
| 5 | GND | power_in | Ground. |
| 6 | LIN | bidirectional | LIN bus single-wire transmitter and receiver; the device supports a 4 V to 36 V supply range with ±45 V LIN bus fault protection. |
| 7 | VSUP | power_in | Device supply voltage, connected to the battery in series with an external reverse blocking diode; absolute maximum supply voltage is 45 V and the stated operating range is 4 V to 36 V. |
| 8 | NC | unconnected | Not connected. |
| 9 | Thermal Pad | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | SON-8-EP(3x3) |
| Category | Interface |
| Pins | 9 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage range | VSUP | -0.3 | 45 | V | 4 | ||
| LIN bus input voltage | VLIN | -45 | 45 | V | 4 | ||
| Logic pin voltage (RXD, TXD, EN) | VLOGIC | -0.3 | 6 | V | 4 | ||
| Ambient temperature range | TA | -40 | 125 | °C | 4 | ||
| Junction temperature range | TJ | -55 | 150 | °C | 4 | ||
| Supply voltage | VSUP | 4 | 36 | V | 5 | ||
| LIN bus input voltage | VLIN | 0 | 36 | V | 5 | ||
| Logic pin voltage (RXD, TXD, EN) | VLOGIC | 0 | 5.25 | V | 5 | ||
| Under voltage VSUP threshold | UVSUP | 2.9 | 3.85 | V | Min is falling edge and Max is rising edge | 5 | |
| Supply current, normal mode, bus dominant | ISUP | 5 | mA | EN = high, bus dominant: RLIN > 500 Ω, CLIN < 10 nF | 5 | ||
| Supply current, standby mode, bus dominant | ISUP | 1 | 2.1 | mA | EN = low, bus dominant: RLIN > 500 Ω, CLIN < 10 nF | 5 | |
| Supply current, normal mode, bus recessive | ISUP | 300 | 650 | µA | EN = high, bus recessive (LIN = VSUP) | 5 | |
| Supply current, standby mode, bus recessive | ISUP | 10 | 30 | µA | EN = low, bus recessive (LIN = VSUP) | 5 | |
| Sleep mode supply current, 4.0 V < VSUP ≤ 14 V | ISUP | 8 | 12 | µA | Sleep Mode: 4.0 V < VSUP ≤ 14 V, LIN = VSUP, EN = 0 V, TXD and RXD floating | 5 | |
| Sleep mode supply current, 14 V < VSUP ≤ 36 V | ISUP | 20 | µA | Sleep Mode: 14 V < VSUP ≤ 36 V, LIN = VSUP, EN = 0 V, TXD and RXD floating | 5 | ||
| Output low voltage | VOL | 0.6 | V | RPU = 2.4 kΩ | 5 | ||
| Low level output current, open drain | IOL | 1.5 | mA | LIN = 0 V, RXD = 0.4 V | 6 | ||
| Low level input voltage (TXD) | VIL | -0.3 | 0.8 | V | 6 | ||
| High level input voltage (TXD) | VIH | 2 | 5.5 | V | 6 | ||
| Low level input leakage current (TXD) | IILG | -5 | 0 | 5 | µA | TXD = low | 6 |
| Internal pull-down resistor value (TXD) | RTXD | 125 | 350 | 800 | kΩ | 6 | |
| HIGH level output voltage (LIN) | VOH | 0.85 | VSUP | LIN recessive, TXD = high, IO = 0 mA, VSUP = 7 V to 36 V | 6 | ||
| HIGH level output voltage (LIN) | VOH | 3 | V | LIN recessive, TXD = high, IO = 0 mA, VSUP = 4 V ≤ VSUP < 7 V | 6 | ||
| LOW level output voltage (LIN) | VOL | 0.2 | VSUP | LIN dominant, TXD = low, VSUP = 7 V to 36 V | 6 | ||
| LOW level output voltage (LIN) | VOL | 1.2 | V | LIN dominant, TXD = low, VSUP = 4 V ≤ VSUP < 7 V | 6 | ||
| VSUP where impact of recessive LIN bus < 5% (non-operating) | VSUP_NON_OP | -0.3 | 45 | V | TXD & RXD open, LIN = 4 V to 45 V | 6 | |
| Limiting current | IBUS_LIM | 40 | 90 | 200 | mA | TXD = 0 V, VLIN = 18 V, RMEAS = 440 Ω, VSUP = 18 V, VBUSdom < 4.518 V | 6 |
| Receiver leakage current, dominant | IBUS_PAS_dom | -1 | mA | LIN = 0 V, VSUP = 12 V, driver off/recessive | 6 | ||
| Receiver leakage current, recessive (LIN = VSUP) | IBUS_PAS_rec2 | -5 | 5 | µA | LIN = VSUP, driver off | 6 | |
| Leakage current, loss of ground | IBUS_NO_GND | -1 | 1 | mA | GND = VSUP, VSUP = 18 V, LIN = 0 V | 6 | |
| Low level input voltage, LIN bus (dominant) | VBUSdom | 0.4 | VSUP | LIN dominant (including LIN dominant for wake up) | 6 | ||
| High level input voltage, LIN bus (recessive) | VBUSrec | 0.6 | VSUP | LIN recessive | 6 | ||
| Receiver center threshold | VBUS_CNT | 0.475 | 0.5 | 0.525 | VSUP | VBUS_CNT = (VIL + VIH)/2 | 6 |
| Hysteresis voltage | VHYS | 0.175 | VSUP | VHYS = (VIL - VIH) | 6 | ||
| Internal pull-up resistor to VSUP | RPU-LIN | 20 | 45 | 60 | kΩ | Normal and standby modes | 6 |
| Pull-up current source to VSUP | IRSLEEP | -20 | -2 | µA | Sleep mode, VSUP = 14 V, LIN = GND | 6 | |
| Low level input voltage (EN) | VIL | -0.3 | 0.8 | V | 6 | ||
| High level input voltage (EN) | VIH | 2 | 5.5 | V | 6 | ||
| Low level input current (EN) | IILG | -5 | 0 | 5 | µA | EN = low | 6 |
| Internal pull-down resistor (EN) | REN | 125 | 205 | 800 | kΩ | 7 | |
| Duty Cycle 1 (ISO/DIS 17987 Param 27) | D112V | 0.396 | THREC(MAX) = 0.744 x VSUP, THDOM(MAX) = 0.581 x VSUP, VSUP = 4 V to 7.4 V, tBIT = 50 µs (20 kbps) | 8 | |||
| Duty Cycle 2 (ISO/DIS 17987 Param 28) | D212V | 0.581 | THREC(MIN) = 0.422 x VSUP, THDOM(MIN) = 0.284 x VSUP, VSUP = 4 V to 7.4 V, tBIT = 50 µs (20 kbps) | 8 | |||
| Duty Cycle 3 (ISO/DIS 17987 Param 29) | D312V | 0.417 | THREC(MAX) = 0.778 x VSUP, THDOM(MAX) = 0.616 x VSUP, VSUP = 7 V to 18 V, tBIT = 96 µs (10.4 kbps) | 8 | |||
| Duty Cycle 3 | D312V | 0.417 | THREC(MAX) = 0.645 x VSUP, THDOM(MAX) = 0.616 x VSUP, VSUP = 4 V to 7 V, tBIT = 96 µs (10.4 kbps) | 8 | |||
| Duty Cycle 4 (ISO/DIS 17987 Param 30) | D412V | 0.59 | THREC(MIN) = 0.389 x VSUP, THDOM(MIN) = 0.251 x VSUP, VSUP = 4.6 V to 7.4 V, tBIT = 96 µs (10.4 kbps) | 8 | |||
| Receiver rising and falling propagation delay time | trx_pdr, trx_pdf | 6 | µs | RRXD = 2.4 kΩ, CRXD = 20 pF | 9 | ||
| Symmetry of receiver propagation delay time | trx_sym | -2 | 2 | µs | Rising edge with respect to falling edge, trx_sym = trx_pdf, trx_pdr, RRXD = 2.4 kΩ, CRXD = 20 pF | 9 | |
| LIN wakeup time (minimum dominant time on LIN bus for wakeup) | tLINBUS | 25 | 65 | 150 | µs | See Fig 7-17, Fig 8-2, and Fig 8-3 | 9 |
| Time to clear false wakeup prevention logic (recessive time to clear bus stuck dominant fault) | tCLEAR | 8 | 25 | 50 | µs | See Fig 8-3 | 9 |
| Mode change delay time | tMODE_CHANGE | 2 | 15 | µs | Standby to normal or normal to sleep mode through EN pin (See Fig 7-15 and Fig 8-4) | 9 | |
| Power up time | tPWR | 1.5 | ms | Upon power up, time for valid data on RXD | 9 | ||
| Junction-to-ambient thermal resistance (DRB) | RΘJA | 48.5 | °C/W | DRB (VSON) 8-pin package | 4 | ||
| Junction-to-case (top) thermal resistance (DRB) | RΘJC(top) | 55.5 | °C/W | DRB (VSON) 8-pin package | 4 | ||
| Junction-to-board thermal resistance (DRB) | RΘJB | 22.2 | °C/W | DRB (VSON) 8-pin package | 4 | ||
| Junction-to-top characterization parameter (DRB) | ΨJT | 1.2 | °C/W | DRB (VSON) 8-pin package | 4 | ||
| Junction-to-board characterization parameter (DRB) | ΨJB | 22.2 | °C/W | DRB (VSON) 8-pin package | 4 | ||
| Junction-to-case (bottom) thermal resistance (DRB) | RΘJC(bot) | 4.8 | °C/W | DRB (VSON) 8-pin package | 5 |
CAD (KiCad official)
- Symbol:
TLIN1027DRBRQ1 - Footprint:
Package_SON:WSON-8-1EP_3x3mm_P0.5mm_EP1.6x2.0mm - 3D model: SON-8-EP(3x3) (KiCad packages3D, STEP)
- 3D model files:
tlin1027drbrq1-etched.step/tlin1027drbrq1-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);tlin1027drbrq1.step/tlin1027drbrq1.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (43 pp, sha256
fc2b405544eeb657, retrieved 2026-10-17, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).