component
TLC3578IPWR
Public Made by Adomby adom
Texas Instruments Analog To Digital Converters (ADC), TSSOP-24. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
main
Ray
Initial commit: component/tlc3578ipwr
dc8e8cc
TLC3578IPWR
Texas Instruments · Analog To Digital Converters (ADC) · TSSOP-24
TLC3578IPWR from Texas Instruments, in a TSSOP-24. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SCLK | input | Serial clock input from the host processor to clock in the input from SDI and clock out the output via SDO, maximum frequency 25 MHz. |
| 2 | FS | input | Frame sync input from DSP; rising edge indicates the start of a serial data frame being transferred. |
| 3 | SDI | input | Serial data input; first 4 MSBs decoded as one 4-bit command, remaining bits filled with zeros except for WRITE CFR command. |
| 4 | EOC/INT | output | End of conversion (EOC) or interrupt to host processor (INT); EOC used in conversion mode 00 only, goes low at end of sampling. |
| 5 | SDO | tri_state | 3-state serial output for the A/D conversion result, MSB first, in high-impedance state when CS is high. |
| 6 | DGND | power_in | Digital ground return for the internal circuitry. |
| 7 | DVDD | power_in | Digital supply voltage, recommended range 2.7 V to 5.5 V. |
| 8 | CS | input | Chip select; falling edge resets internal 4-bit counter and enables SDI and SCLK, when high SDO is in high-impedance state. |
| 9 | A0 | input | Analog signal input channel 0, internally multiplexed with driving source impedance ≤ 25 Ω for normal sampling. |
| 10 | A1 | input | Analog signal input channel 1, internally multiplexed with driving source impedance ≤ 25 Ω for normal sampling. |
| 11 | A2 | input | Analog signal input channel 2, internally multiplexed with driving source impedance ≤ 25 Ω for normal sampling. |
| 12 | A3 | input | Analog signal input channel 3, internally multiplexed with driving source impedance ≤ 25 Ω for normal sampling. |
| 13 | A4 | input | Analog signal input channel 4, internally multiplexed with driving source impedance ≤ 25 Ω for normal sampling. |
| 14 | A5 | input | Analog signal input channel 5, internally multiplexed with driving source impedance ≤ 25 Ω for normal sampling. |
| 15 | A6 | input | Analog signal input channel 6, internally multiplexed with driving source impedance ≤ 25 Ω for normal sampling. |
| 16 | A7 | input | Analog signal input channel 7, internally multiplexed with driving source impedance ≤ 25 Ω for normal sampling. |
| 17 | AVDD | power_in | Analog supply voltage, recommended range 4.75 V to 5.5 V. |
| 18 | AGND | power_in | Analog ground return for the internal circuitry. |
| 19 | REFP | input | External positive reference input, range 3.96 V to 4.04 V; install decoupling capacitors 10 µF in parallel with 0.1 µF between REFP and REFM. |
| 20 | REFM | input | External low reference input; connect to AGND to establish the ±10 V bipolar input range. |
| 21 | COMP | passive | Internal compensation pin; install 0.1 µF compensation capacitor between this pin and AGND. |
| 22 | AGND | power_in | Analog ground return for the internal circuitry. |
| 23 | AVDD | power_in | Analog supply voltage, recommended range 4.75 V to 5.5 V. |
| 24 | CSTART | input | External sampling trigger signal; high-to-low transition starts sampling, low-to-high transition puts S/H in hold mode and starts conversion with 15 ns internal delay. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | TSSOP-24 |
| Category | Data Acquisition |
| Pins | 24 |
CAD (KiCad official)
- Symbol:
TLC3578IPWR - Footprint:
Package_SO:TSSOP-24_4.4x7.8mm_P0.65mm - 3D model: TSSOP-24 (KiCad packages3D, STEP)
- 3D model files:
tlc3578ipwr-etched.step/tlc3578ipwr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);tlc3578ipwr.step/tlc3578ipwr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (54 pp, sha256
a98de3fa366cd8b4, retrieved 2026-09-23, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.2, primaryclaude-haiku-4-5-20251001(text), consensusclaude-sonnet-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# TLC3578IPWR
**Texas Instruments** · Analog To Digital Converters (ADC) · TSSOP-24
TLC3578IPWR from Texas Instruments, in a TSSOP-24. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SCLK | input | Serial clock input from the host processor to clock in the input from SDI and clock out the output via SDO, maximum frequency 25 MHz. |
| 2 | FS | input | Frame sync input from DSP; rising edge indicates the start of a serial data frame being transferred. |
| 3 | SDI | input | Serial data input; first 4 MSBs decoded as one 4-bit command, remaining bits filled with zeros except for WRITE CFR command. |
| 4 | EOC/INT | output | End of conversion (EOC) or interrupt to host processor (INT); EOC used in conversion mode 00 only, goes low at end of sampling. |
| 5 | SDO | tri_state | 3-state serial output for the A/D conversion result, MSB first, in high-impedance state when CS is high. |
| 6 | DGND | power_in | Digital ground return for the internal circuitry. |
| 7 | DVDD | power_in | Digital supply voltage, recommended range 2.7 V to 5.5 V. |
| 8 | CS | input | Chip select; falling edge resets internal 4-bit counter and enables SDI and SCLK, when high SDO is in high-impedance state. |
| 9 | A0 | input | Analog signal input channel 0, internally multiplexed with driving source impedance ≤ 25 Ω for normal sampling. |
| 10 | A1 | input | Analog signal input channel 1, internally multiplexed with driving source impedance ≤ 25 Ω for normal sampling. |
| 11 | A2 | input | Analog signal input channel 2, internally multiplexed with driving source impedance ≤ 25 Ω for normal sampling. |
| 12 | A3 | input | Analog signal input channel 3, internally multiplexed with driving source impedance ≤ 25 Ω for normal sampling. |
| 13 | A4 | input | Analog signal input channel 4, internally multiplexed with driving source impedance ≤ 25 Ω for normal sampling. |
| 14 | A5 | input | Analog signal input channel 5, internally multiplexed with driving source impedance ≤ 25 Ω for normal sampling. |
| 15 | A6 | input | Analog signal input channel 6, internally multiplexed with driving source impedance ≤ 25 Ω for normal sampling. |
| 16 | A7 | input | Analog signal input channel 7, internally multiplexed with driving source impedance ≤ 25 Ω for normal sampling. |
| 17 | AVDD | power_in | Analog supply voltage, recommended range 4.75 V to 5.5 V. |
| 18 | AGND | power_in | Analog ground return for the internal circuitry. |
| 19 | REFP | input | External positive reference input, range 3.96 V to 4.04 V; install decoupling capacitors 10 µF in parallel with 0.1 µF between REFP and REFM. |
| 20 | REFM | input | External low reference input; connect to AGND to establish the ±10 V bipolar input range. |
| 21 | COMP | passive | Internal compensation pin; install 0.1 µF compensation capacitor between this pin and AGND. |
| 22 | AGND | power_in | Analog ground return for the internal circuitry. |
| 23 | AVDD | power_in | Analog supply voltage, recommended range 4.75 V to 5.5 V. |
| 24 | CSTART | input | External sampling trigger signal; high-to-low transition starts sampling, low-to-high transition puts S/H in hold mode and starts conversion with 15 ns internal delay. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | TSSOP-24 |
| Category | Data Acquisition |
| Pins | 24 |
## CAD (KiCad official)
- Symbol: `TLC3578IPWR`
- Footprint: `Package_SO:TSSOP-24_4.4x7.8mm_P0.65mm`
- 3D model: TSSOP-24 (KiCad packages3D, STEP)
- 3D model files: `tlc3578ipwr-etched.step` / `tlc3578ipwr-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `tlc3578ipwr.step` / `tlc3578ipwr.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/tlc2574) (54 pp, sha256 `a98de3fa366cd8b4`, retrieved 2026-09-23, tier: lcsc)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.2`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/tlc3578ipwr-datasheet.pdf)