main
Ray
Publish 0.1.0
281fce8
THN 15-2413
Traco Power · Power Supplies - Board Mount · 6-DIP Module
THN 15-2413 from Traco Power, in a 6-DIP Module. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). The symbol is generated from that pin table, the footprint is an Adom_Gen land derived from the manufacturer drawing, and the 3D model is generated to fit it.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | +Vin (Vcc) | power_in | Positive input for the 18-36 VDC input range of this model, with surge voltage limited to 50 VDC max. for 100 ms on 24 Vin models. |
| 2 | -Vin (GND) | power_in | Negative input (GND) return for the 18-36 VDC input, which is also the reference for the Remote On/Off pin. |
| 3 | +Vout | power_out | Positive regulated output at 15 VDC nominal, rated for 1'000 mA max. at this model's full load. |
| 4 | Trim | passive | Output voltage adjustment input for single output models, allowing ±10% of nominal by external trim resistor. |
| 5 | -Vout | power_out | Negative output return for the regulated +Vout output. |
| 6 | Remote On/Off | input | Remote control input referenced to -Vin: on at 3.0 to 15 VDC or open circuit, off at 0 to 1.2 VDC or short circuit. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Traco Power |
| Package | 6-DIP Module |
| Category | Power Supplies - Board Mount |
| Pins | 6 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input voltage range | 18 | 24 | 36 | VDC | 24 Vin model, 18-36 VDC (24 VDC nom.) | 1 | |
| Output voltage | Vnom | 15 | VDC | 15 Vout single output model | 1 | ||
| Surge voltage | 50 | VDC | 24 Vin models, 100 ms max. | 2 | |||
| Under voltage lockout | 14.5 | 15.5 | 17.5 | VDC | 24 Vin models | 2 | |
| Output voltage adjustment | -10 | 10 | % | ±10% other models, single output models only, by external trim resistor | 2 | ||
| Voltage set accuracy | -1 | 1 | % | 3 | |||
| Regulation input variation | 0.2 | % | single output models, Vmin-Vmax | 3 | |||
| Regulation load variation | 0.2 | % | single output models, 0-100% load | 3 | |||
| Temperature coefficient | -0.02 | 0.02 | %/K | 3 | |||
| Capacitive load | 660 | µF | 15 Vout single output models | 3 | |||
| Start-up time | 30 | ms | 3 | ||||
| Output current limitation | 120 | 150 | 175 | % | of Iout max. | 3 | |
| Overvoltage protection | 112 | 164 | % | of Vout nom. | 3 | ||
| Remote control on voltage | 3 | 15 | VDC | passive = on, or open circuit; refers to Remote and -Vin pin | 4 | ||
| Remote control off voltage | 0 | 1.2 | VDC | off, or short circuit; refers to Remote and -Vin pin | 4 | ||
| Remote pin input current | -0.5 | 1 | mA | 4 | |||
| Operating temperature | -40 | 85 | °C | without heatsink; +90°C max with heatsink THN-HS1 | 4 | ||
| Case temperature | 105 | °C | 4 | ||||
| Storage temperature | -55 | 125 | °C | 4 | |||
| Switching frequency | 360 | 400 | 440 | kHz | PWM | 4 | |
| Isolation test voltage input to case | 1000 | VDC | 60 s | 4 | |||
| Isolation test voltage output to case | 1000 | VDC | 60 s | 4 | |||
| Isolation resistance input to output | 1000 | MΩ | 500 VDC | 4 | |||
| Isolation capacitance input to output | 1000 | pF | 100 kHz, 1 V | 4 | |||
| Thermal impedance case to ambient | 18.2 | K/W | case to ambient, without heatsink | 5 | |||
| Thermal impedance case to ambient with heatsink | 15.8 | K/W | with heatsink THN-HS1 | 5 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | Copper | Pin Material Copper | 4 |
CAD (Adom-generated)
- Symbol:
THN 15-2413 - Footprint:
Adom_Gen:Traco_Power_THN_15-2_29a51b - 3D model: generated to fit the land (STEP)
- 3D model files:
thn-15-2413-etched.step/thn-15-2413-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);thn-15-2413.step/thn-15-2413.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Traco Power datasheet (5 pp, sha256
ff9e377ace1f2691, retrieved 2026-11-16, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: symbol generated from the datasheet pin table; footprint an Adom_Gen land derived from the manufacturer drawing; 3D model generated to fit that land.
# THN 15-2413
**Traco Power** · Power Supplies - Board Mount · 6-DIP Module
THN 15-2413 from Traco Power, in a 6-DIP Module. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). The symbol is generated from that pin table, the footprint is an Adom_Gen land derived from the manufacturer drawing, and the 3D model is generated to fit it.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | +Vin (Vcc) | power_in | Positive input for the 18-36 VDC input range of this model, with surge voltage limited to 50 VDC max. for 100 ms on 24 Vin models. |
| 2 | -Vin (GND) | power_in | Negative input (GND) return for the 18-36 VDC input, which is also the reference for the Remote On/Off pin. |
| 3 | +Vout | power_out | Positive regulated output at 15 VDC nominal, rated for 1'000 mA max. at this model's full load. |
| 4 | Trim | passive | Output voltage adjustment input for single output models, allowing ±10% of nominal by external trim resistor. |
| 5 | -Vout | power_out | Negative output return for the regulated +Vout output. |
| 6 | Remote On/Off | input | Remote control input referenced to -Vin: on at 3.0 to 15 VDC or open circuit, off at 0 to 1.2 VDC or short circuit. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Traco Power |
| Package | 6-DIP Module |
| Category | Power Supplies - Board Mount |
| Pins | 6 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input voltage range | | 18 | 24 | 36 | VDC | 24 Vin model, 18-36 VDC (24 VDC nom.) | 1 |
| Output voltage | Vnom | | 15 | | VDC | 15 Vout single output model | 1 |
| Surge voltage | | | | 50 | VDC | 24 Vin models, 100 ms max. | 2 |
| Under voltage lockout | | 14.5 | 15.5 | 17.5 | VDC | 24 Vin models | 2 |
| Output voltage adjustment | | -10 | | 10 | % | ±10% other models, single output models only, by external trim resistor | 2 |
| Voltage set accuracy | | -1 | | 1 | % | | 3 |
| Regulation input variation | | | | 0.2 | % | single output models, Vmin-Vmax | 3 |
| Regulation load variation | | | | 0.2 | % | single output models, 0-100% load | 3 |
| Temperature coefficient | | -0.02 | | 0.02 | %/K | | 3 |
| Capacitive load | | | | 660 | µF | 15 Vout single output models | 3 |
| Start-up time | | | | 30 | ms | | 3 |
| Output current limitation | | 120 | 150 | 175 | % | of Iout max. | 3 |
| Overvoltage protection | | 112 | | 164 | % | of Vout nom. | 3 |
| Remote control on voltage | | 3 | | 15 | VDC | passive = on, or open circuit; refers to Remote and -Vin pin | 4 |
| Remote control off voltage | | 0 | | 1.2 | VDC | off, or short circuit; refers to Remote and -Vin pin | 4 |
| Remote pin input current | | -0.5 | | 1 | mA | | 4 |
| Operating temperature | | -40 | | 85 | °C | without heatsink; +90°C max with heatsink THN-HS1 | 4 |
| Case temperature | | | | 105 | °C | | 4 |
| Storage temperature | | -55 | | 125 | °C | | 4 |
| Switching frequency | | 360 | 400 | 440 | kHz | PWM | 4 |
| Isolation test voltage input to case | | | | 1000 | VDC | 60 s | 4 |
| Isolation test voltage output to case | | | | 1000 | VDC | 60 s | 4 |
| Isolation resistance input to output | | 1000 | | | MΩ | 500 VDC | 4 |
| Isolation capacitance input to output | | | | 1000 | pF | 100 kHz, 1 V | 4 |
| Thermal impedance case to ambient | | | 18.2 | | K/W | case to ambient, without heatsink | 5 |
| Thermal impedance case to ambient with heatsink | | | 15.8 | | K/W | with heatsink THN-HS1 | 5 |
## Materials and finish
As the datasheet states them (page.json `metadata.appearance`; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | Copper | | Pin Material Copper | 4 |
## CAD (Adom-generated)
- Symbol: `THN 15-2413`
- Footprint: `Adom_Gen:Traco_Power_THN_15-2_29a51b`
- 3D model: generated to fit the land (STEP)
- 3D model files: `thn-15-2413-etched.step` / `thn-15-2413-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `thn-15-2413.step` / `thn-15-2413.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Traco Power datasheet](https://www.tracopower.com/products/thn15.pdf) (5 pp, sha256 `ff9e377ace1f2691`, retrieved 2026-11-16, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** symbol generated from the datasheet pin table; footprint an Adom_Gen land derived from the manufacturer drawing; 3D model generated to fit that land.
[Datasheet PDF](docs/thn-15-2413-datasheet.pdf)