main
Ray
Publish 0.2.0
cc7ddad
TD1837
Techcode Semicon · DC-DC Converters · ESOP-8
TD1837 from Techcode Semicon, in a ESOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SW | output | Switch Node. Output from the internal high-side power MOSFET (250mΩ RDS(on)). Requires an external low-VF Schottky rectifier to ground placed close to the pin to reduce switching spikes. Switch voltage range -0.5V to VIN+0.5V. |
| 2 | EN | input | Enable Input (positive logic). Pulling below the falling threshold (~1.7V) or leaving floating shuts the chip down; pulling above the rising threshold (~1.9V, spec 1.3V min to 2.2V max) enables the chip. Internal ~1MΩ pull-down to GND. |
| 3 | COMP | output | Compensation. Output of the internal GM error amplifier. Connect an external R-C compensation network here to set loop dynamics. Internally clamped between ~0.9V (min) and ~2.0V (max) during operation; do not drive above 2.6V. |
| 4 | FB | input | Feedback. Inverting input to the internal error amplifier. An external resistive divider from VOUT to GND sets the output voltage; the divider is compared to the internal 0.8V reference (VFB = 0.780V to 0.820V). |
| 5 | GND | power_in | Ground. Common return for the device and shared with the exposed thermal pad. Connect as close as possible to the output capacitor while avoiding high-current switch paths. The exposed pad must be tied to the GND plane for optimal thermal performance. |
| 6 | FREQ | input | Switching Frequency Program Input. Connect a resistor RFREQ from this pin to ground to program the oscillator frequency (up to 1MHz). RFREQ(kΩ) = 100000/fs(kHz) − 5. For VIN ≥ 64V, set fsw below 400kHz. |
| 7 | VIN | power_in | Input Supply. Supplies all internal control circuitry, bootstrap regulators, and the high-side power MOSFET. Absolute maximum 80V (operating range 12V to 80V; VIN UVLO ~7.2V rising, ~6.5V falling). A decoupling capacitor to ground must be placed close to this pin. |
| 8 | BST | power_in | Bootstrap. Positive supply for the internal floating high-side MOSFET gate driver. Connect a bypass capacitor (typ. 0.1μF) between BST and SW. Internally regulated to ~5V above SW; BST-to-SW absolute maximum is +5V. |
| 9 | GND | power_in | Exposed pad; the maker lists it with pin 5 ("5 GND, Exposed pad ... Connect exposed pad to GND plane for optimal thermal performance"). KiCad's SOIC-8-1EP numbers the exposed pad 9. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Techcode Semicon |
| Package | ESOP-8 |
| Category | DC-DC Converters |
| Pins | 9 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Feedback Voltage | VFB | 0.78 | 0.8 | 0.82 | V | 12V < VIN < 75V | 5 |
| Top Switch RDS(ON) | RDS(ON)-T | 175 | 250 | 330 | mΩ | VBST, VSW = 5V | 5 |
| Current Limit | 2.2 | 4.7 | A | 5 | |||
| Oscillator Frequency | 0.6 | 0.8 | MHz | RFREQ = 150kΩ | 5 | ||
| EN Up Threshold | 1.3 | 2.2 | V | 5 | |||
| Shutdown Supply Current | 1 | 3 | μA | VEN < 0.3V | 5 | ||
| VIN Supply Voltage | VIN | -0.3 | 80 | V | 5 | ||
| Switch Voltage | VSW | -0.5 | V | 5 | |||
| BST to SW | -0.3 | 5 | V | 5 | |||
| All other Pins | -0.3 | 5 | V | 5 | |||
| Junction Temperature | TJ | 150 | ºC | 5 | |||
| Maximum Lead Soldering Temperature | TSDR | 260 | ºC | 10 Seconds | 5 |
CAD (KiCad official)
- Symbol:
TD1837 - Footprint:
Package_SO:SOIC-8-1EP_3.9x4.9mm_P1.27mm_EP2.41x3.3mm - 3D model: ESOP-8 (KiCad packages3D, STEP)
- 3D model files:
td1837-etched.step/td1837-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);td1837.step/td1837.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Techcode Semicon datasheet (14 pp, sha256
664614e8ad9c691d, retrieved 2026-11-16, tier: manufacturer) - Extractor:
ds2sf(Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# TD1837
**Techcode Semicon** · DC-DC Converters · ESOP-8
TD1837 from Techcode Semicon, in a ESOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SW | output | Switch Node. Output from the internal high-side power MOSFET (250mΩ RDS(on)). Requires an external low-VF Schottky rectifier to ground placed close to the pin to reduce switching spikes. Switch voltage range -0.5V to VIN+0.5V. |
| 2 | EN | input | Enable Input (positive logic). Pulling below the falling threshold (~1.7V) or leaving floating shuts the chip down; pulling above the rising threshold (~1.9V, spec 1.3V min to 2.2V max) enables the chip. Internal ~1MΩ pull-down to GND. |
| 3 | COMP | output | Compensation. Output of the internal GM error amplifier. Connect an external R-C compensation network here to set loop dynamics. Internally clamped between ~0.9V (min) and ~2.0V (max) during operation; do not drive above 2.6V. |
| 4 | FB | input | Feedback. Inverting input to the internal error amplifier. An external resistive divider from VOUT to GND sets the output voltage; the divider is compared to the internal 0.8V reference (VFB = 0.780V to 0.820V). |
| 5 | GND | power_in | Ground. Common return for the device and shared with the exposed thermal pad. Connect as close as possible to the output capacitor while avoiding high-current switch paths. The exposed pad must be tied to the GND plane for optimal thermal performance. |
| 6 | FREQ | input | Switching Frequency Program Input. Connect a resistor RFREQ from this pin to ground to program the oscillator frequency (up to 1MHz). RFREQ(kΩ) = 100000/fs(kHz) − 5. For VIN ≥ 64V, set fsw below 400kHz. |
| 7 | VIN | power_in | Input Supply. Supplies all internal control circuitry, bootstrap regulators, and the high-side power MOSFET. Absolute maximum 80V (operating range 12V to 80V; VIN UVLO ~7.2V rising, ~6.5V falling). A decoupling capacitor to ground must be placed close to this pin. |
| 8 | BST | power_in | Bootstrap. Positive supply for the internal floating high-side MOSFET gate driver. Connect a bypass capacitor (typ. 0.1μF) between BST and SW. Internally regulated to ~5V above SW; BST-to-SW absolute maximum is +5V. |
| 9 | GND | power_in | Exposed pad; the maker lists it with pin 5 ("5 GND, Exposed pad ... Connect exposed pad to GND plane for optimal thermal performance"). KiCad's SOIC-8-1EP numbers the exposed pad 9. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Techcode Semicon |
| Package | ESOP-8 |
| Category | DC-DC Converters |
| Pins | 9 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Feedback Voltage | VFB | 0.78 | 0.8 | 0.82 | V | 12V < VIN < 75V | 5 |
| Top Switch RDS(ON) | RDS(ON)-T | 175 | 250 | 330 | mΩ | VBST, VSW = 5V | 5 |
| Current Limit | | 2.2 | | 4.7 | A | | 5 |
| Oscillator Frequency | | 0.6 | | 0.8 | MHz | RFREQ = 150kΩ | 5 |
| EN Up Threshold | | 1.3 | | 2.2 | V | | 5 |
| Shutdown Supply Current | | | 1 | 3 | μA | VEN < 0.3V | 5 |
| VIN Supply Voltage | VIN | -0.3 | | 80 | V | | 5 |
| Switch Voltage | VSW | -0.5 | | | V | | 5 |
| BST to SW | | -0.3 | | 5 | V | | 5 |
| All other Pins | | -0.3 | | 5 | V | | 5 |
| Junction Temperature | TJ | | | 150 | ºC | | 5 |
| Maximum Lead Soldering Temperature | TSDR | | | 260 | ºC | 10 Seconds | 5 |
## CAD (KiCad official)
- Symbol: `TD1837`
- Footprint: `Package_SO:SOIC-8-1EP_3.9x4.9mm_P1.27mm_EP2.41x3.3mm`
- 3D model: ESOP-8 (KiCad packages3D, STEP)
- 3D model files: `td1837-etched.step` / `td1837-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `td1837.step` / `td1837.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Techcode Semicon datasheet]() (14 pp, sha256 `664614e8ad9c691d`, retrieved 2026-11-16, tier: manufacturer)
- **Extractor:** `ds2sf` (Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/td1837-datasheet.pdf)