Generated by kicad-footprint-generator · KiCad file format 20260206
TAS5825MRHBR
Texas Instruments · Audio Amplifiers · VQFN-32(5x5)
TAS5825MRHBR from Texas Instruments, in a VQFN-32(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | BST_A+ | passive | Connection point for the OUT_A+ bootstrap capacitor which creates the floating supply for the high-side gate drive of OUT_A+. |
| 2 | OUT_A+ | output | Positive pin for differential speaker amplifier output A (Class-D half-bridge output, switches between 0 V and PVDD). |
| 3 | PVDD | power_in | PVDD voltage input; power-stage supply, recommended range 4.5 V to 26.4 V. |
| 4 | PVDD | power_in | PVDD voltage input; power-stage supply, recommended range 4.5 V to 26.4 V. |
| 5 | DGND | power_in | Digital ground reference for the digital circuitry. |
| 6 | DVDD | power_in | 3.3-V or 1.8-V digital power supply input for the low-voltage digital circuitry. |
| 7 | VR_DIG | power_out | Internally regulated 1.5-V digital supply voltage output; this pin must not be used to drive external devices. |
| 8 | ADR | input | Analog input; a resistor value pulled down to GND on this pin sets the device I2C address (see table 表 9-5). |
| 9 | GPIO0 | bidirectional | General-purpose input/output; function programmable via registers 0x60/0x61, can be configured as CMOS output or open-drain WARNZ/FAULTZ output. |
| 10 | GPIO1 | bidirectional | General-purpose input/output; function programmable via registers 0x60/0x62, can be configured as CMOS output or open-drain WARNZ/FAULTZ output. |
| 11 | GPIO2 | bidirectional | General-purpose input/output; function programmable via registers 0x60/0x63, can be configured as CMOS output or open-drain WARNZ/FAULTZ output. |
| 12 | LRCLK | input | Word-select (left/right or frame-sync) clock for the serial audio input data on SDIN; marks left/right channel boundary in I2S/LJ/RJ or frame-sync boundary in TDM mode. |
| 13 | SCLK | input | Bit clock (also called BCLK) for the serial audio data port; required SCLK/LRCLK duty cycle 40%-60%, supported SCLK rates 32/64 fS. |
| 14 | SDIN | input | Data line input to the serial audio data port; accepts up to 32-bit, MSB-first, two's-complement audio data. |
| 15 | SDA | bidirectional | I2C serial control data interface input/output, supports 100 kHz and 400 kHz data-transfer rates. |
| 16 | SCL | input | I2C serial control clock input, supports 100 kHz and 400 kHz data-transfer rates. |
| 17 | PDN | input | Power-down control, active-low; pulling PDN low places the amplifier in Shutdown and turns off all internal regulators. |
| 18 | GVDD | power_out | Gate-drive internal regulator output (5 V, derived from PVDD); this pin must not be used to drive external devices. |
| 19 | AVDD | power_out | Internally regulated 5-V analog supply voltage output; this pin must not be used to drive external devices. |
| 20 | AGND | power_in | Analog ground reference. |
| 21 | PVDD | power_in | PVDD voltage input; power-stage supply, recommended range 4.5 V to 26.4 V. |
| 22 | PVDD | power_in | PVDD voltage input; power-stage supply, recommended range 4.5 V to 26.4 V. |
| 23 | OUT_B+ | output | Positive pin for differential speaker amplifier output B (Class-D half-bridge output, switches between 0 V and PVDD). |
| 24 | BST_B+ | passive | Connection point for the OUT_B+ bootstrap capacitor which creates the floating supply for the high-side gate drive of OUT_B+. |
| 25 | PGND | power_in | Ground reference for the power-device (output stage) circuitry; connect to system ground. |
| 26 | PGND | power_in | Ground reference for the power-device (output stage) circuitry; connect to system ground. |
| 27 | OUT_B- | output | Negative pin for differential speaker amplifier output B (Class-D half-bridge output, switches between 0 V and PVDD). |
| 28 | BST_B- | passive | Connection point for the OUT_B- bootstrap capacitor which creates the floating supply for the high-side gate drive of OUT_B-. |
| 29 | BST_A- | passive | Connection point for the OUT_A- bootstrap capacitor which creates the floating supply for the high-side gate drive of OUT_A-. |
| 30 | OUT_A- | output | Negative pin for differential speaker amplifier output A (Class-D half-bridge output, switches between 0 V and PVDD). |
| 31 | PGND | power_in | Ground reference for the power-device (output stage) circuitry; connect to system ground. |
| 32 | PGND | power_in | Ground reference for the power-device (output stage) circuitry; connect to system ground. |
| 33 | PowerPAD | power_in | Exposed PowerPAD thermal/ground pad on the package underside; must be connected to system ground and soldered to the PCB for thermal and mechanical performance. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | VQFN-32(5x5) |
| Category | Amplifiers/Comparators |
| Pins | 33 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Power supply inputs DVDD | DVDD | 1.62 | 3.63 | V | over operating free-air temperature range | 6 | |
| Power supply inputs PVDD | PVDD | 4.5 | 26.4 | V | over operating free-air temperature range | 6 | |
| Minimum speaker load, BTL Mode | RSPK | 3.2 | 4 | Ω | BTL Mode | 6 | |
| Minimum speaker load, PBTL Mode | RSPK | 1.6 | 2 | Ω | PBTL Mode | 6 | |
| Minimum inductor value in LC filter under short-circuit condition | LOUT | 1 | 4.7 | µH | under short-circuit condition | 6 | |
| DVDD Low-voltage digital supply | DVDD | -0.3 | 3.9 | V | Free-air room temperature 25°C | 6 | |
| PVDD PVDD supply | PVDD | -0.3 | 30 | V | Free-air room temperature 25°C | 6 | |
| DVDD referenced digital inputs | VI(DigIn) | -0.5 | V | max printed as VDVDD + 0.5 | 6 | ||
| Voltage at speaker output pins | VI(SPK_OUTxx) | -0.3 | 32 | V | 6 | ||
| Ambient operating temperature | TA | -25 | 85 | °C | 6 | ||
| Storage temperature | Tstg | -40 | 125 | °C | 6 | ||
| Input logic high current level for DVDD referenced digital input pins | /IIH/ | 10 | µA | VIN(DigIn) = VDVDD | 7 | ||
| Input logic low current level for DVDD referenced digital input pins | /IIL/ | -10 | µA | VIN(DigIn) = 0 V | 7 | ||
| Input logic high threshold for DVDD referenced digital inputs | VIH(Digin) | 70 | %VDVDD | 7 | |||
| Input logic low threshold for DVDD referenced digital inputs | VIL(Digin) | 30 | %VDVDD | 7 | |||
| Output logic high voltage level | VOH(Digin) | 80 | %VDVDD | IOH = 4 mA | 7 | ||
| Output logic low voltage level | VOL(Digin) | 20 | %VDVDD | IOH = –4 mA (as printed) | 7 | ||
| Allowable load capacitance for each I2C line | CL(I2C) | 400 | pF | 7 | |||
| Support SCL frequency, fast mode | fSCL(fast) | 400 | kHz | No wait states, fast mode | 7 | ||
| Support SCL frequency, slow mode | fSCL(slow) | 100 | kHz | No wait states, slow mode | 7 | ||
| Required LRCK/FS to SCLK rising edge delay | tDLY | 5 | ns | 7 | |||
| Allowable SCLK duty cycle | DSCLK | 40 | 60 | % | 7 | ||
| Supported input sample rates | fS | 32 | 192 | kHz | 7 | ||
| Supported SCLK frequencies | fSCLK | 32 | 64 | fS | 7 | ||
| Turn-off Time | toff | 10 | ms | Excluding volume ramp | 7 | ||
| Programmable Gain | AV(SPK_AMP) | 4.87 | 29.5 | V | Value is peak voltage, disregarding clipping due to lower PVDD; measured at 0 dB input (1FS) | 8 | |
| Amplifier gain error | ΔAV(SPK_AMP) | 0.5 | dB | Gain = 29.5 Vp | 8 | ||
| Over-Current Error Threshold | OCETHRES | 7.5 | A | Any short to supply, ground, or other channels | 8 | ||
| PVDD over voltage error threshold | OVETHRES(PVDD) | 28 | V | 8 | |||
| PVDD under voltage error threshold | UVETHRES(PVDD) | 4.2 | V | 8 | |||
| Over temperature error threshold | OTETHRES | 160 | °C | 8 | |||
| Amplifier offset voltage | /VOS/ | -7.5 | 7.5 | mV | Measured differentially with zero input data, gain 29.5 Vp, VPVDD = 16 V | 8 | |
| SCLK period | tSCLK | 40 | ns | Serial Audio Port Timing – Target Mode | 10 | ||
| SCLK pulse width, low | tSCLKL | 16 | ns | Serial Audio Port Timing – Target Mode | 10 | ||
| SCLK pulse width, high | tSCLKH | 16 | ns | Serial Audio Port Timing – Target Mode | 10 | ||
| SCLK rising to LRCK/FS edge | tSL | 8 | ns | Serial Audio Port Timing – Target Mode | 10 | ||
| LRCK/FS edge to SCLK rising edge | tLS | 8 | ns | Serial Audio Port Timing – Target Mode | 10 | ||
| Data setup time, before SCLK rising edge | tSU | 8 | ns | Serial Audio Port Timing – Target Mode | 10 | ||
| Data hold time, after SCLK rising edge | tDH | 8 | ns | Serial Audio Port Timing – Target Mode | 10 | ||
| Data delay time from SCLK falling edge | tDFS | 15 | ns | Serial Audio Port Timing – Target Mode | 10 | ||
| Bus free time between a STOP and START condition, fast mode | tBUF | 1.3 | µs | I2C Bus Timing – Fast | 10 | ||
| Low period of the SCL clock, fast mode | tLOW | 1.3 | µs | I2C Bus Timing – Fast | 10 | ||
| High period of the SCL clock, fast mode | tHI | 600 | ns | I2C Bus Timing – Fast | 10 | ||
| Setup time for (repeated) START condition, fast mode | tRS-SU | 600 | ns | I2C Bus Timing – Fast | 10 | ||
| Data setup time, fast mode | tD-SU | 100 | ns | I2C Bus Timing – Fast | 10 | ||
| Data hold time, fast mode | tD-HD | 0 | 900 | ns | I2C Bus Timing – Fast | 10 | |
| Rise time of SCL signal, fast mode | tSCL-R | 300 | ns | Min printed as 20 + 0.1CB | 10 | ||
| Rise time of SCL signal after a repeated START condition and after an acknowledge bit, fast mode | tSCL-R1 | 300 | ns | Min printed as 20 + 0.1CB | 10 | ||
| Fall time of SCL signal, fast mode | tSCL-F | 300 | ns | Min printed as 20 + 0.1CB | 10 | ||
| Rise time of SDA signal, fast mode | tSDA-R | 300 | ns | Min printed as 20 + 0.1CB | 10 | ||
| Fall time of SDA signal, fast mode | tSDA-F | 300 | ns | Min printed as 20 + 0.1CB | 10 | ||
| Setup time for STOP condition, fast mode | tP-SU | 600 | ns | I2C Bus Timing – Fast | 10 | ||
| Pulse width of spike suppressed, fast mode | tSP | 50 | ns | I2C Bus Timing – Fast | 10 | ||
| Junction-to-ambient thermal resistance, JEDEC 4-layer PCB | RθJA | 30 | °C/W | JEDEC standard 4-layer PCB | 6 | ||
| Junction-to-ambient thermal resistance, TAS5825MEVM-4 4-layer PCB | RθJA | 24.1 | °C/W | TAS5825MEVM-4 4-layer PCB | 6 | ||
| Junction-to-case (top) thermal resistance, JEDEC 4-layer PCB | RθJC(top) | 19.1 | °C/W | JEDEC standard 4-layer PCB | 6 | ||
| Junction-to-case (top) thermal resistance, TAS5825MEVM-4 4-layer PCB | RθJC(top) | 19.1 | °C/W | TAS5825MEVM-4 4-layer PCB | 6 | ||
| Junction-to-board thermal resistance, JEDEC 4-layer PCB | RθJB | 9.9 | °C/W | JEDEC standard 4-layer PCB | 6 | ||
| Junction-to-board thermal resistance, TAS5825MEVM-4 4-layer PCB | RθJB | 9.9 | °C/W | TAS5825MEVM-4 4-layer PCB | 6 |
CAD (KiCad official)
- Symbol:
TAS5825MRHBR - Footprint:
Package_DFN_QFN:QFN-32-1EP_5x5mm_P0.5mm_EP3.3x3.3mm - 3D model: VQFN-32(5x5) (KiCad packages3D, STEP)
- 3D model files:
tas5825mrhbr-etched.step/tas5825mrhbr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);tas5825mrhbr.step/tas5825mrhbr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (107 pp, sha256
1baa7964a2e3b784, retrieved 2026-09-23, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.2, primaryclaude-haiku-4-5-20251001(text), consensusclaude-sonnet-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).