← Commit history

Initial commit: component/tas5825mrhbr

Ray ·acdd2e0976 ·
2 files changed +363
README.mdadded+70
@@ -0,0 +1,70 @@+# TAS5825MRHBR++**Texas Instruments** · Audio Amplifiers · VQFN-32(5x5)++TAS5825MRHBR from Texas Instruments, in a VQFN-32(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | BST_A+ | passive | Connection point for the OUT_A+ bootstrap capacitor which creates the floating supply for the high-side gate drive of OUT_A+. |+| 2 | OUT_A+ | output | Positive pin for differential speaker amplifier output A (Class-D half-bridge output, switches between 0 V and PVDD). |+| 3 | PVDD | power_in | PVDD voltage input; power-stage supply, recommended range 4.5 V to 26.4 V. |+| 4 | PVDD | power_in | PVDD voltage input; power-stage supply, recommended range 4.5 V to 26.4 V. |+| 5 | DGND | power_in | Digital ground reference for the digital circuitry. |+| 6 | DVDD | power_in | 3.3-V or 1.8-V digital power supply input for the low-voltage digital circuitry. |+| 7 | VR_DIG | power_out | Internally regulated 1.5-V digital supply voltage output; this pin must not be used to drive external devices. |+| 8 | ADR | input | Analog input; a resistor value pulled down to GND on this pin sets the device I2C address (see table 表 9-5). |+| 9 | GPIO0 | bidirectional | General-purpose input/output; function programmable via registers 0x60/0x61, can be configured as CMOS output or open-drain WARNZ/FAULTZ output. |+| 10 | GPIO1 | bidirectional | General-purpose input/output; function programmable via registers 0x60/0x62, can be configured as CMOS output or open-drain WARNZ/FAULTZ output. |+| 11 | GPIO2 | bidirectional | General-purpose input/output; function programmable via registers 0x60/0x63, can be configured as CMOS output or open-drain WARNZ/FAULTZ output. |+| 12 | LRCLK | input | Word-select (left/right or frame-sync) clock for the serial audio input data on SDIN; marks left/right channel boundary in I2S/LJ/RJ or frame-sync boundary in TDM mode. |+| 13 | SCLK | input | Bit clock (also called BCLK) for the serial audio data port; required SCLK/LRCLK duty cycle 40%-60%, supported SCLK rates 32/64 fS. |+| 14 | SDIN | input | Data line input to the serial audio data port; accepts up to 32-bit, MSB-first, two's-complement audio data. |+| 15 | SDA | bidirectional | I2C serial control data interface input/output, supports 100 kHz and 400 kHz data-transfer rates. |+| 16 | SCL | input | I2C serial control clock input, supports 100 kHz and 400 kHz data-transfer rates. |+| 17 | PDN | input | Power-down control, active-low; pulling PDN low places the amplifier in Shutdown and turns off all internal regulators. |+| 18 | GVDD | power_out | Gate-drive internal regulator output (5 V, derived from PVDD); this pin must not be used to drive external devices. |+| 19 | AVDD | power_out | Internally regulated 5-V analog supply voltage output; this pin must not be used to drive external devices. |+| 20 | AGND | power_in | Analog ground reference. |+| 21 | PVDD | power_in | PVDD voltage input; power-stage supply, recommended range 4.5 V to 26.4 V. |+| 22 | PVDD | power_in | PVDD voltage input; power-stage supply, recommended range 4.5 V to 26.4 V. |+| 23 | OUT_B+ | output | Positive pin for differential speaker amplifier output B (Class-D half-bridge output, switches between 0 V and PVDD). |+| 24 | BST_B+ | passive | Connection point for the OUT_B+ bootstrap capacitor which creates the floating supply for the high-side gate drive of OUT_B+. |+| 25 | PGND | power_in | Ground reference for the power-device (output stage) circuitry; connect to system ground. |+| 26 | PGND | power_in | Ground reference for the power-device (output stage) circuitry; connect to system ground. |+| 27 | OUT_B- | output | Negative pin for differential speaker amplifier output B (Class-D half-bridge output, switches between 0 V and PVDD). |+| 28 | BST_B- | passive | Connection point for the OUT_B- bootstrap capacitor which creates the floating supply for the high-side gate drive of OUT_B-. |+| 29 | BST_A- | passive | Connection point for the OUT_A- bootstrap capacitor which creates the floating supply for the high-side gate drive of OUT_A-. |+| 30 | OUT_A- | output | Negative pin for differential speaker amplifier output A (Class-D half-bridge output, switches between 0 V and PVDD). |+| 31 | PGND | power_in | Ground reference for the power-device (output stage) circuitry; connect to system ground. |+| 32 | PGND | power_in | Ground reference for the power-device (output stage) circuitry; connect to system ground. |+| 33 | PowerPAD | power_in | Exposed PowerPAD thermal/ground pad on the package underside; must be connected to system ground and soldered to the PCB for thermal and mechanical performance. |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Texas Instruments |+| Package | VQFN-32(5x5) |+| Category | Amplifiers/Comparators |+| Pins | 33 |++## CAD (KiCad official)++- Symbol: `TAS5825MRHBR`+- Footprint: `Package_DFN_QFN:QFN-32-1EP_5x5mm_P0.5mm_EP3.3x3.3mm`+- 3D model: VQFN-32(5x5) (KiCad packages3D, STEP)+- 3D model files: `tas5825mrhbr-etched.step` / `tas5825mrhbr-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `tas5825mrhbr.step` / `tas5825mrhbr.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/tas5825m) (107 pp, sha256 `1baa7964a2e3b784`, retrieved 2026-09-23, tier: lcsc)+- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.2`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/tas5825mrhbr-datasheet.pdf)
page.jsonadded+293
@@ -0,0 +1,293 @@+{+  "slug": "tas5825mrhbr",+  "version": "0.1.0",+  "type": "component",+  "description": "Texas Instruments Audio Amplifiers, VQFN-32(5x5). Datasheet-verified pinout, KiCad symbol/footprint/3D.",+  "tags": [+    "component",+    "amplifiers-comparators",+    "tas5825mrhbr",+    "factory-2.0.0",+    "extractor-text"+  ],+  "dependencies": {},+  "hero": {+    "type": "image",+    "path": "docs/hero.png"+  },+  "files": [+    "page.json",+    "README.md",+    "tas5825mrhbr.kicad_sym",+    "tas5825mrhbr.kicad_mod",+    "tas5825mrhbr.glb",+    "tas5825mrhbr.step",+    "tas5825mrhbr.lbr",+    "docs/hero.png",+    "docs/tas5825mrhbr-datasheet.pdf",+    "viewers/symbol.html",+    "viewers/footprint.html"+  ],+  "component": {+    "mpn": "TAS5825MRHBR",+    "manufacturer": "Texas Instruments",+    "package": "VQFN-32(5x5)",+    "pin_count": 33,+    "category": "Amplifiers/Comparators",+    "subcategory": "Audio Amplifiers",+    "datasheet": "https://www.ti.com/cn/lit/gpn/tas5825m",+    "parts": {+      "symbol": "tas5825mrhbr.kicad_sym",+      "footprint": "tas5825mrhbr.kicad_mod",+      "model_3d": "tas5825mrhbr-etched.glb",+      "model_3d_plain": "tas5825mrhbr.glb",+      "model_3d_step": "tas5825mrhbr-etched.step",+      "model_3d_step_plain": "tas5825mrhbr.step",+      "lbr": "tas5825mrhbr.lbr"+    },+    "distributor_links": {+      "lcsc": "C471049"+    },+    "pins": [+      {+        "number": "1",+        "name": "BST_A+",+        "type": "passive",+        "description": "Connection point for the OUT_A+ bootstrap capacitor which creates the floating supply for the high-side gate drive of OUT_A+."+      },+      {+        "number": "2",+        "name": "OUT_A+",+        "type": "output",+        "description": "Positive pin for differential speaker amplifier output A (Class-D half-bridge output, switches between 0 V and PVDD)."+      },+      {+        "number": "3",+        "name": "PVDD",+        "type": "power_in",+        "description": "PVDD voltage input; power-stage supply, recommended range 4.5 V to 26.4 V."+      },+      {+        "number": "4",+        "name": "PVDD",+        "type": "power_in",+        "description": "PVDD voltage input; power-stage supply, recommended range 4.5 V to 26.4 V."+      },+      {+        "number": "5",+        "name": "DGND",+        "type": "power_in",+        "description": "Digital ground reference for the digital circuitry."+      },+      {+        "number": "6",+        "name": "DVDD",+        "type": "power_in",+        "description": "3.3-V or 1.8-V digital power supply input for the low-voltage digital circuitry."+      },+      {+        "number": "7",+        "name": "VR_DIG",+        "type": "power_out",+        "description": "Internally regulated 1.5-V digital supply voltage output; this pin must not be used to drive external devices."+      },+      {+        "number": "8",+        "name": "ADR",+        "type": "input",+        "description": "Analog input; a resistor value pulled down to GND on this pin sets the device I2C address (see table 表 9-5)."+      },+      {+        "number": "9",+        "name": "GPIO0",+        "type": "bidirectional",+        "description": "General-purpose input/output; function programmable via registers 0x60/0x61, can be configured as CMOS output or open-drain WARNZ/FAULTZ output."+      },+      {+        "number": "10",+        "name": "GPIO1",+        "type": "bidirectional",+        "description": "General-purpose input/output; function programmable via registers 0x60/0x62, can be configured as CMOS output or open-drain WARNZ/FAULTZ output."+      },+      {+        "number": "11",+        "name": "GPIO2",+        "type": "bidirectional",+        "description": "General-purpose input/output; function programmable via registers 0x60/0x63, can be configured as CMOS output or open-drain WARNZ/FAULTZ output."+      },+      {+        "number": "12",+        "name": "LRCLK",+        "type": "input",+        "description": "Word-select (left/right or frame-sync) clock for the serial audio input data on SDIN; marks left/right channel boundary in I2S/LJ/RJ or frame-sync boundary in TDM mode."+      },+      {+        "number": "13",+        "name": "SCLK",+        "type": "input",+        "description": "Bit clock (also called BCLK) for the serial audio data port; required SCLK/LRCLK duty cycle 40%-60%, supported SCLK rates 32/64 fS."+      },+      {+        "number": "14",+        "name": "SDIN",+        "type": "input",+        "description": "Data line input to the serial audio data port; accepts up to 32-bit, MSB-first, two's-complement audio data."+      },+      {+        "number": "15",+        "name": "SDA",+        "type": "bidirectional",+        "description": "I2C serial control data interface input/output, supports 100 kHz and 400 kHz data-transfer rates."+      },+      {+        "number": "16",+        "name": "SCL",+        "type": "input",+        "description": "I2C serial control clock input, supports 100 kHz and 400 kHz data-transfer rates."+      },+      {+        "number": "17",+        "name": "PDN",+        "type": "input",+        "description": "Power-down control, active-low; pulling PDN low places the amplifier in Shutdown and turns off all internal regulators."+      },+      {+        "number": "18",+        "name": "GVDD",+        "type": "power_out",+        "description": "Gate-drive internal regulator output (5 V, derived from PVDD); this pin must not be used to drive external devices."+      },+      {+        "number": "19",+        "name": "AVDD",+        "type": "power_out",+        "description": "Internally regulated 5-V analog supply voltage output; this pin must not be used to drive external devices."+      },+      {+        "number": "20",+        "name": "AGND",+        "type": "power_in",+        "description": "Analog ground reference."+      },+      {+        "number": "21",+        "name": "PVDD",+        "type": "power_in",+        "description": "PVDD voltage input; power-stage supply, recommended range 4.5 V to 26.4 V."+      },+      {+        "number": "22",+        "name": "PVDD",+        "type": "power_in",+        "description": "PVDD voltage input; power-stage supply, recommended range 4.5 V to 26.4 V."+      },+      {+        "number": "23",+        "name": "OUT_B+",+        "type": "output",+        "description": "Positive pin for differential speaker amplifier output B (Class-D half-bridge output, switches between 0 V and PVDD)."+      },+      {+        "number": "24",+        "name": "BST_B+",+        "type": "passive",+        "description": "Connection point for the OUT_B+ bootstrap capacitor which creates the floating supply for the high-side gate drive of OUT_B+."+      },+      {+        "number": "25",+        "name": "PGND",+        "type": "power_in",+        "description": "Ground reference for the power-device (output stage) circuitry; connect to system ground."+      },+      {+        "number": "26",+        "name": "PGND",+        "type": "power_in",+        "description": "Ground reference for the power-device (output stage) circuitry; connect to system ground."+      },+      {+        "number": "27",+        "name": "OUT_B-",+        "type": "output",+        "description": "Negative pin for differential speaker amplifier output B (Class-D half-bridge output, switches between 0 V and PVDD)."+      },+      {+        "number": "28",+        "name": "BST_B-",+        "type": "passive",+        "description": "Connection point for the OUT_B- bootstrap capacitor which creates the floating supply for the high-side gate drive of OUT_B-."+      },+      {+        "number": "29",+        "name": "BST_A-",+        "type": "passive",+        "description": "Connection point for the OUT_A- bootstrap capacitor which creates the floating supply for the high-side gate drive of OUT_A-."+      },+      {+        "number": "30",+        "name": "OUT_A-",+        "type": "output",+        "description": "Negative pin for differential speaker amplifier output A (Class-D half-bridge output, switches between 0 V and PVDD)."+      },+      {+        "number": "31",+        "name": "PGND",+        "type": "power_in",+        "description": "Ground reference for the power-device (output stage) circuitry; connect to system ground."+      },+      {+        "number": "32",+        "name": "PGND",+        "type": "power_in",+        "description": "Ground reference for the power-device (output stage) circuitry; connect to system ground."+      },+      {+        "number": "33",+        "name": "PowerPAD",+        "type": "power_in",+        "description": "Exposed PowerPAD thermal/ground pad on the package underside; must be connected to system ground and soldered to the PCB for thermal and mechanical performance."+      }+    ],+    "provenance": {+      "extractor": "extract_pins 0.2",+      "factory_chain": {+        "factory": "2.0.0",+        "extractor": "extract_pins 0.2",+        "primary_model": "claude-haiku-4-5-20251001",+        "primary_mode": "text",+        "consensus_model": "claude-sonnet-5",+        "consensus": "agreed",+        "guards": "pin_guards 0.1: passed",+        "guard_notes": [+          "exposed pad 33 added from the footprint"+        ],+        "pages_sent": 107,+        "cost_usd": 1.0488,+        "at": "2026-09-23T13:10:32"+      },+      "datasheet": {+        "url": "https://www.ti.com/cn/lit/gpn/tas5825m",+        "pages": 107,+        "sha256": "1baa7964a2e3b784",+        "source_tier": "lcsc"+      },+      "cad": "KiCad official (CC-BY-SA 4.0)",+      "pins": {+        "total": 33,+        "described": 33,+        "cites_pages": true,+        "refuses_to_fabricate": true+      }+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }+  },+  "visibility": "public",+  "org": "adom",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  }+}\ No newline at end of file