main
Ray
tas5731mphpr: specified limits as data (metadata.characteristics, 55 rows from the datasheet)
bc2f478
TAS5731MPHPR
Texas Instruments · Audio Amplifiers · TQFP-48-EP(7x7)
TAS5731MPHPR from Texas Instruments, in a TQFP-48-EP(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | OUT_A | output | Half-bridge A PWM audio output pin. |
| 2 | PVDD_AB | power_in | Power-supply input for half-bridges A and B (8 to 26.4 V); requires 100-nF ceramic decoupling capacitor placed close to pin. |
| 3 | PVDD_AB | power_in | Power-supply input for half-bridges A and B (8 to 26.4 V); requires 100-nF ceramic decoupling capacitor placed close to pin. |
| 4 | BST_A | power_in | High-side bootstrap supply for half-bridge A gate driver; connect 10-nF ceramic capacitor to OUT_A. |
| 5 | NC | unconnected | No internal connection; may be left floating or connected to ground. |
| 6 | SSTIMER | passive | Soft-start ramp time control; leave floating for BD mode or connect 2.2-nF capacitor to ground for AD mode. |
| 7 | NC | unconnected | No internal connection; may be left floating or connected to ground. |
| 8 | PBTL | input | Mode select input with internal pulldown; logic low selects BTL mode (default), logic high selects PBTL mode. |
| 9 | AVSS | power_in | Analog 3.3-V supply ground connection. |
| 10 | PLL_FLTM | output | PLL negative loop-filter terminal; connect to external RC network with 47-nF and 4.7-nF capacitors and 470-Ω resistor. |
| 11 | PLL_FLTP | output | PLL positive loop-filter terminal; connect to external RC network as specified for PLL_FLTM. |
| 12 | VR_ANA | power_out | Internally regulated 1.8-V analog supply; must not be used to power external devices. |
| 13 | AVDD | power_in | 3.3-V analog power supply (3.0 to 3.6 V nominal); requires quality decoupling capacitors placed close to pin. |
| 14 | ADR/FAULT | bidirectional | Dual-function pin: sets I2C address to 0x36 if pulled high, 0x34 if pulled low; can be configured as active-low fault output. |
| 15 | MCLK | input | Master clock input (2.8224 to 24.576-MHz) with 5-V tolerance, 40-60% duty cycle, and 5-ns maximum rise/fall time. |
| 16 | OSC_RES | output | Oscillator trim resistor connection; connect 18.2-kΩ 1% resistor to DVSSO for oscillator frequency calibration. |
| 17 | DVSSO | power_in | Oscillator ground; oscillator trim resistor connects from OSC_RES to this pin. |
| 18 | VR_DIG | power_out | Internally regulated 1.8-V digital supply; must not be used to power external devices. |
| 19 | PDN | input | Active-low power-down input with internal pullup; initiates PWM stop sequence and noise shaper shutdown. |
| 20 | LRCLK | input | I2S left/right clock (sample-rate clock) input with 5-V tolerance; supports 8 to 48-kHz sample rates. |
| 21 | SCLK | input | I2S serial bit clock input (1.024 to 12.288-MHz at 32×, 48×, or 64×fS) with 5-V tolerance and 8-ns rise/fall time. |
| 22 | SDIN | input | Serial audio data input supporting 16-bit, 20-bit, and 24-bit I2S, left-justified, and right-justified data formats. |
| 23 | SDA | bidirectional | I2C open-drain serial data line with internal pullup; requires external 4.7-kΩ pullup resistor to DVDD. |
| 24 | SCL | input | I2C serial control clock input supporting 100-kHz and 400-kHz operation with 5-V tolerance. |
| 25 | RESET | input | Active-low asynchronous reset input with internal pullup; must be held low for 100-µs minimum at power-up. |
| 26 | STEST | input | Factory test pin; must be connected directly to DVSS for proper operation. |
| 27 | DVDD | power_in | 3.3-V digital power supply (3.0 to 3.6 V nominal); requires quality decoupling capacitors placed close to pin. |
| 28 | DVSS | power_in | Digital ground connection. |
| 29 | GND | power_in | Analog ground for power stage; should be connected to system ground. |
| 30 | AGND | power_in | Local analog ground for power-stage output section; provides ground reference for output pins. |
| 31 | VREG | power_out | Digital regulator output; not to be used for powering external circuitry. |
| 32 | GVDD_OUT | power_out | Gate-drive regulator output derived from PVDD; supplies bootstrap charging diode for high-side gate drivers. |
| 33 | BST_D | power_in | High-side bootstrap supply for half-bridge D gate driver; connect 10-nF ceramic capacitor to OUT_D. |
| 34 | PVDD_CD | power_in | Power-supply input for half-bridges C and D (8 to 26.4 V); requires 100-nF ceramic decoupling capacitor placed close to pin. |
| 35 | PVDD_CD | power_in | Power-supply input for half-bridges C and D (8 to 26.4 V); requires 100-nF ceramic decoupling capacitor placed close to pin. |
| 36 | OUT_D | output | Half-bridge D PWM output pin for audio power amplification. |
| 37 | PGND_CD | power_in | Power-stage ground for half-bridges C and D. |
| 38 | PGND_CD | power_in | Power-stage ground for half-bridges C and D. |
| 39 | OUT_C | output | Half-bridge C PWM output pin for audio power amplification. |
| 40 | NC | unconnected | No internal connection; may be left floating or connected to ground. |
| 41 | NC | unconnected | No internal connection; may be left floating or connected to ground. |
| 42 | BST_C | power_in | High-side bootstrap supply for half-bridge C gate driver; connect 10-nF ceramic capacitor to OUT_C. |
| 43 | BST_B | power_in | High-side bootstrap supply for half-bridge B gate driver; connect 10-nF ceramic capacitor to OUT_B. |
| 44 | NC | unconnected | No internal connection; may be left floating or connected to ground. |
| 45 | NC | unconnected | No internal connection; may be left floating or connected to ground. |
| 46 | OUT_B | output | Half-bridge B PWM output pin for audio power amplification. |
| 47 | PGND_AB | power_in | Power-stage ground for half-bridges A and B. |
| 48 | PGND_AB | power_in | Power-stage ground for half-bridges A and B. |
| 49 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | TQFP-48-EP(7x7) |
| Category | Amplifiers/Comparators |
| Pins | 49 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Digital/analog supply voltage | DVDD, AVDD | 3 | 3.3 | 3.6 | V | 8 | |
| Half-bridge supply voltage | PVDD_x | 8 | 26.4 | V | 8 | ||
| High-level input voltage (5-V tolerant) | VIH | 2 | V | 8 | |||
| Low-level input voltage (5-V tolerant) | VIL | 0.8 | V | 8 | |||
| Operating ambient temperature range | TA | 0 | 85 | °C | 8 | ||
| Operating junction temperature range | TJ | 0 | 125 | °C | 9 | ||
| Load impedance (PBTL) | RL (PBTL) | 2 | Ω | Output filter: L = 15 μH, C = 680 nF | 9 | ||
| Load impedance (BTL) | RL (BTL) | 4 | Ω | Output filter: L = 15 μH, C = 680 nF | 9 | ||
| Load impedance (SE) | RL (SE) | 2 | Ω | Output filter: L = 15 μH, C = 680 nF | 9 | ||
| Output-filter inductance | LO | 10 | μH | Minimum output inductance under short-circuit condition | 9 | ||
| MCLK frequency | fMCLKI | 2.8224 | 24.576 | MHz | 9 | ||
| MCLK duty cycle | 40 | 50 | 60 | % | 9 | ||
| Rise/fall time for MCLK | tr/tf(MCLK) | 5 | ns | 9 | |||
| Output PWM switch frequency (11.025/22.05/44.1-kHz data rate) | fPWM | 352.8 | kHz | 11.025/22.05/44.1-kHz data rate ±2% | 9 | ||
| Output PWM switch frequency (48/24/12/8/16/32-kHz data rate) | fPWM | 384 | kHz | 48/24/12/8/16/32-kHz data rate ±2% | 9 | ||
| Supply voltage DVDD, AVDD (absolute) | DVDD, AVDD | -0.3 | 4.2 | V | 8 | ||
| Supply voltage PVDD_x (absolute) | PVDD_x | -0.3 | 30 | V | 8 | ||
| 3.3-V digital input voltage | -0.5 | V | max DVDD + 0.5 V | 8 | |||
| 5-V tolerant digital input voltage (except MCLK) | -0.5 | V | max DVDD + 2.5 V (note 3: pin voltage not to exceed 6 V) | 8 | |||
| 5-V tolerant MCLK input voltage | -0.5 | V | max AVDD + 2.5 V | 8 | |||
| OUT_x to PGND_x voltage | 32 | V | DC plus peak ac below limit (note 4) | 8 | |||
| BST_x to PGND_x voltage | 39 | V | DC plus peak ac below limit (note 4) | 8 | |||
| Input clamp current | IIK | -20 | 20 | mA | 8 | ||
| Output clamp current | IOK | -20 | 20 | mA | 8 | ||
| Operating free-air temperature | 0 | 85 | °C | 8 | |||
| Operating junction temperature range (absolute) | 0 | 150 | °C | 8 | |||
| Storage temperature range | Tstg | -40 | 125 | °C | 8 | ||
| Junction-to-ambient thermal resistance | θJA | 27.9 | °C/W | PHP (48 pins) | 8 | ||
| Junction-to-board thermal resistance | θJB | 13 | °C/W | PHP (48 pins) | 8 | ||
| Junction-to-case (bottom) thermal resistance | θJC(bottom) | 1.1 | °C/W | PHP (48 pins) | 8 | ||
| Junction-to-case (top) thermal resistance | θJC(top) | 20.7 | °C/W | PHP (48 pins) | 8 | ||
| High-level output voltage (ADR/FAULT and SDA) | VOH | 2.4 | V | IOH = –4 mA | 9 | ||
| Low-level output voltage (ADR/FAULT and SDA) | VOL | 0.5 | V | IOL = 4 mA; DVDD = 3 V | 9 | ||
| Low-level input current | IIL | 75 | μA | VI < VIL; DVDD = AVDD = 3.6 V | 9 | ||
| High-level input current | IIH | 75 | μA | VI > VIH; DVDD = AVDD = 3.6 V | 9 | ||
| 3.3 V supply current (normal mode) | IDD | 49 | 68 | mA | Normal mode | 9 | |
| 3.3 V supply current (reset) | IDD | 23 | 38 | mA | Reset (RESET = low, PDN = high) | 9 | |
| Supply current PVDD_x (normal mode) | IPVDD | 32 | 50 | mA | No load (PVDD_x); normal mode | 9 | |
| Supply current PVDD_x (reset) | IPVDD | 4 | 8 | mA | No load (PVDD_x); Reset (RESET = low, PDN = high) | 9 | |
| Drain-to-source resistance, LS | rDS(on) | 80 | mΩ | TJ = 25°C, includes metallization resistance | 9 | ||
| Drain-to-source resistance, HS | rDS(on) | 80 | mΩ | TJ = 25°C, includes metallization resistance | 9 | ||
| Undervoltage protection limit (PVDD falling) | Vuvp | 6.4 | V | PVDD falling | 9 | ||
| Undervoltage protection limit (PVDD rising) | Vuvp,hyst | 7.1 | V | PVDD rising | 9 | ||
| Overtemperature error | OTE | 150 | °C | 10 | |||
| Extra temperature drop required to recover from error | OTEHYST | 30 | °C | 10 | |||
| Overcurrent limit protection | IOC | 4.5 | A | Output to output short in BTL mode | 10 | ||
| Overcurrent response time | IOCT | 150 | ns | 10 | |||
| Setup time, LRCLK to SCLK rising edge | tsu1 | 10 | ns | 11 | |||
| Hold time, LRCLK from SCLK rising edge | th1 | 10 | ns | 11 | |||
| Setup time, SDIN to SCLK rising edge | tsu2 | 10 | ns | 11 | |||
| Hold time, SDIN from SCLK rising edge | th2 | 10 | ns | 11 | |||
| Frequency, SCLK (32×fS, 48×fS, 64×fS) | fSCLKIN | 1.024 | 12.288 | MHz | CL = 30 pF | 11 | |
| LRCLK frequency | 8 | 48 | 48 | kHz | 11 | ||
| SCLK duty cycle | 40 | 50 | 60 | % | 11 | ||
| LRCLK duty cycle | 40 | 50 | 60 | % | 11 |
CAD (KiCad official)
- Symbol:
TAS5731MPHPR - Footprint:
Package_QFP:TQFP-48-1EP_7x7mm_P0.5mm_EP5x5mm - 3D model: TQFP-48-EP(7x7) (KiCad packages3D, STEP)
- 3D model files:
tas5731mphpr-etched.step/tas5731mphpr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);tas5731mphpr.step/tas5731mphpr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (71 pp, sha256
b548f5b31dc8dd9b, retrieved 2026-09-26, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.2, primaryclaude-haiku-4-5-20251001(text), consensusclaude-sonnet-4-6(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# TAS5731MPHPR
**Texas Instruments** · Audio Amplifiers · TQFP-48-EP(7x7)
TAS5731MPHPR from Texas Instruments, in a TQFP-48-EP(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | OUT_A | output | Half-bridge A PWM audio output pin. |
| 2 | PVDD_AB | power_in | Power-supply input for half-bridges A and B (8 to 26.4 V); requires 100-nF ceramic decoupling capacitor placed close to pin. |
| 3 | PVDD_AB | power_in | Power-supply input for half-bridges A and B (8 to 26.4 V); requires 100-nF ceramic decoupling capacitor placed close to pin. |
| 4 | BST_A | power_in | High-side bootstrap supply for half-bridge A gate driver; connect 10-nF ceramic capacitor to OUT_A. |
| 5 | NC | unconnected | No internal connection; may be left floating or connected to ground. |
| 6 | SSTIMER | passive | Soft-start ramp time control; leave floating for BD mode or connect 2.2-nF capacitor to ground for AD mode. |
| 7 | NC | unconnected | No internal connection; may be left floating or connected to ground. |
| 8 | PBTL | input | Mode select input with internal pulldown; logic low selects BTL mode (default), logic high selects PBTL mode. |
| 9 | AVSS | power_in | Analog 3.3-V supply ground connection. |
| 10 | PLL_FLTM | output | PLL negative loop-filter terminal; connect to external RC network with 47-nF and 4.7-nF capacitors and 470-Ω resistor. |
| 11 | PLL_FLTP | output | PLL positive loop-filter terminal; connect to external RC network as specified for PLL_FLTM. |
| 12 | VR_ANA | power_out | Internally regulated 1.8-V analog supply; must not be used to power external devices. |
| 13 | AVDD | power_in | 3.3-V analog power supply (3.0 to 3.6 V nominal); requires quality decoupling capacitors placed close to pin. |
| 14 | ADR/FAULT | bidirectional | Dual-function pin: sets I2C address to 0x36 if pulled high, 0x34 if pulled low; can be configured as active-low fault output. |
| 15 | MCLK | input | Master clock input (2.8224 to 24.576-MHz) with 5-V tolerance, 40-60% duty cycle, and 5-ns maximum rise/fall time. |
| 16 | OSC_RES | output | Oscillator trim resistor connection; connect 18.2-kΩ 1% resistor to DVSSO for oscillator frequency calibration. |
| 17 | DVSSO | power_in | Oscillator ground; oscillator trim resistor connects from OSC_RES to this pin. |
| 18 | VR_DIG | power_out | Internally regulated 1.8-V digital supply; must not be used to power external devices. |
| 19 | PDN | input | Active-low power-down input with internal pullup; initiates PWM stop sequence and noise shaper shutdown. |
| 20 | LRCLK | input | I2S left/right clock (sample-rate clock) input with 5-V tolerance; supports 8 to 48-kHz sample rates. |
| 21 | SCLK | input | I2S serial bit clock input (1.024 to 12.288-MHz at 32×, 48×, or 64×fS) with 5-V tolerance and 8-ns rise/fall time. |
| 22 | SDIN | input | Serial audio data input supporting 16-bit, 20-bit, and 24-bit I2S, left-justified, and right-justified data formats. |
| 23 | SDA | bidirectional | I2C open-drain serial data line with internal pullup; requires external 4.7-kΩ pullup resistor to DVDD. |
| 24 | SCL | input | I2C serial control clock input supporting 100-kHz and 400-kHz operation with 5-V tolerance. |
| 25 | RESET | input | Active-low asynchronous reset input with internal pullup; must be held low for 100-µs minimum at power-up. |
| 26 | STEST | input | Factory test pin; must be connected directly to DVSS for proper operation. |
| 27 | DVDD | power_in | 3.3-V digital power supply (3.0 to 3.6 V nominal); requires quality decoupling capacitors placed close to pin. |
| 28 | DVSS | power_in | Digital ground connection. |
| 29 | GND | power_in | Analog ground for power stage; should be connected to system ground. |
| 30 | AGND | power_in | Local analog ground for power-stage output section; provides ground reference for output pins. |
| 31 | VREG | power_out | Digital regulator output; not to be used for powering external circuitry. |
| 32 | GVDD_OUT | power_out | Gate-drive regulator output derived from PVDD; supplies bootstrap charging diode for high-side gate drivers. |
| 33 | BST_D | power_in | High-side bootstrap supply for half-bridge D gate driver; connect 10-nF ceramic capacitor to OUT_D. |
| 34 | PVDD_CD | power_in | Power-supply input for half-bridges C and D (8 to 26.4 V); requires 100-nF ceramic decoupling capacitor placed close to pin. |
| 35 | PVDD_CD | power_in | Power-supply input for half-bridges C and D (8 to 26.4 V); requires 100-nF ceramic decoupling capacitor placed close to pin. |
| 36 | OUT_D | output | Half-bridge D PWM output pin for audio power amplification. |
| 37 | PGND_CD | power_in | Power-stage ground for half-bridges C and D. |
| 38 | PGND_CD | power_in | Power-stage ground for half-bridges C and D. |
| 39 | OUT_C | output | Half-bridge C PWM output pin for audio power amplification. |
| 40 | NC | unconnected | No internal connection; may be left floating or connected to ground. |
| 41 | NC | unconnected | No internal connection; may be left floating or connected to ground. |
| 42 | BST_C | power_in | High-side bootstrap supply for half-bridge C gate driver; connect 10-nF ceramic capacitor to OUT_C. |
| 43 | BST_B | power_in | High-side bootstrap supply for half-bridge B gate driver; connect 10-nF ceramic capacitor to OUT_B. |
| 44 | NC | unconnected | No internal connection; may be left floating or connected to ground. |
| 45 | NC | unconnected | No internal connection; may be left floating or connected to ground. |
| 46 | OUT_B | output | Half-bridge B PWM output pin for audio power amplification. |
| 47 | PGND_AB | power_in | Power-stage ground for half-bridges A and B. |
| 48 | PGND_AB | power_in | Power-stage ground for half-bridges A and B. |
| 49 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | TQFP-48-EP(7x7) |
| Category | Amplifiers/Comparators |
| Pins | 49 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Digital/analog supply voltage | DVDD, AVDD | 3 | 3.3 | 3.6 | V | | 8 |
| Half-bridge supply voltage | PVDD_x | 8 | | 26.4 | V | | 8 |
| High-level input voltage (5-V tolerant) | VIH | 2 | | | V | | 8 |
| Low-level input voltage (5-V tolerant) | VIL | | | 0.8 | V | | 8 |
| Operating ambient temperature range | TA | 0 | | 85 | °C | | 8 |
| Operating junction temperature range | TJ | 0 | | 125 | °C | | 9 |
| Load impedance (PBTL) | RL (PBTL) | 2 | | | Ω | Output filter: L = 15 μH, C = 680 nF | 9 |
| Load impedance (BTL) | RL (BTL) | 4 | | | Ω | Output filter: L = 15 μH, C = 680 nF | 9 |
| Load impedance (SE) | RL (SE) | 2 | | | Ω | Output filter: L = 15 μH, C = 680 nF | 9 |
| Output-filter inductance | LO | 10 | | | μH | Minimum output inductance under short-circuit condition | 9 |
| MCLK frequency | fMCLKI | 2.8224 | | 24.576 | MHz | | 9 |
| MCLK duty cycle | | 40 | 50 | 60 | % | | 9 |
| Rise/fall time for MCLK | tr/tf(MCLK) | | | 5 | ns | | 9 |
| Output PWM switch frequency (11.025/22.05/44.1-kHz data rate) | fPWM | | 352.8 | | kHz | 11.025/22.05/44.1-kHz data rate ±2% | 9 |
| Output PWM switch frequency (48/24/12/8/16/32-kHz data rate) | fPWM | | 384 | | kHz | 48/24/12/8/16/32-kHz data rate ±2% | 9 |
| Supply voltage DVDD, AVDD (absolute) | DVDD, AVDD | -0.3 | | 4.2 | V | | 8 |
| Supply voltage PVDD_x (absolute) | PVDD_x | -0.3 | | 30 | V | | 8 |
| 3.3-V digital input voltage | | -0.5 | | | V | max DVDD + 0.5 V | 8 |
| 5-V tolerant digital input voltage (except MCLK) | | -0.5 | | | V | max DVDD + 2.5 V (note 3: pin voltage not to exceed 6 V) | 8 |
| 5-V tolerant MCLK input voltage | | -0.5 | | | V | max AVDD + 2.5 V | 8 |
| OUT_x to PGND_x voltage | | | | 32 | V | DC plus peak ac below limit (note 4) | 8 |
| BST_x to PGND_x voltage | | | | 39 | V | DC plus peak ac below limit (note 4) | 8 |
| Input clamp current | IIK | -20 | | 20 | mA | | 8 |
| Output clamp current | IOK | -20 | | 20 | mA | | 8 |
| Operating free-air temperature | | 0 | | 85 | °C | | 8 |
| Operating junction temperature range (absolute) | | 0 | | 150 | °C | | 8 |
| Storage temperature range | Tstg | -40 | | 125 | °C | | 8 |
| Junction-to-ambient thermal resistance | θJA | | 27.9 | | °C/W | PHP (48 pins) | 8 |
| Junction-to-board thermal resistance | θJB | | 13 | | °C/W | PHP (48 pins) | 8 |
| Junction-to-case (bottom) thermal resistance | θJC(bottom) | | 1.1 | | °C/W | PHP (48 pins) | 8 |
| Junction-to-case (top) thermal resistance | θJC(top) | | 20.7 | | °C/W | PHP (48 pins) | 8 |
| High-level output voltage (ADR/FAULT and SDA) | VOH | 2.4 | | | V | IOH = –4 mA | 9 |
| Low-level output voltage (ADR/FAULT and SDA) | VOL | | | 0.5 | V | IOL = 4 mA; DVDD = 3 V | 9 |
| Low-level input current | IIL | | | 75 | μA | VI < VIL; DVDD = AVDD = 3.6 V | 9 |
| High-level input current | IIH | | | 75 | μA | VI > VIH; DVDD = AVDD = 3.6 V | 9 |
| 3.3 V supply current (normal mode) | IDD | | 49 | 68 | mA | Normal mode | 9 |
| 3.3 V supply current (reset) | IDD | | 23 | 38 | mA | Reset (RESET = low, PDN = high) | 9 |
| Supply current PVDD_x (normal mode) | IPVDD | | 32 | 50 | mA | No load (PVDD_x); normal mode | 9 |
| Supply current PVDD_x (reset) | IPVDD | | 4 | 8 | mA | No load (PVDD_x); Reset (RESET = low, PDN = high) | 9 |
| Drain-to-source resistance, LS | rDS(on) | | 80 | | mΩ | TJ = 25°C, includes metallization resistance | 9 |
| Drain-to-source resistance, HS | rDS(on) | | 80 | | mΩ | TJ = 25°C, includes metallization resistance | 9 |
| Undervoltage protection limit (PVDD falling) | Vuvp | | 6.4 | | V | PVDD falling | 9 |
| Undervoltage protection limit (PVDD rising) | Vuvp,hyst | | 7.1 | | V | PVDD rising | 9 |
| Overtemperature error | OTE | | 150 | | °C | | 10 |
| Extra temperature drop required to recover from error | OTEHYST | | 30 | | °C | | 10 |
| Overcurrent limit protection | IOC | | 4.5 | | A | Output to output short in BTL mode | 10 |
| Overcurrent response time | IOCT | | 150 | | ns | | 10 |
| Setup time, LRCLK to SCLK rising edge | tsu1 | 10 | | | ns | | 11 |
| Hold time, LRCLK from SCLK rising edge | th1 | 10 | | | ns | | 11 |
| Setup time, SDIN to SCLK rising edge | tsu2 | 10 | | | ns | | 11 |
| Hold time, SDIN from SCLK rising edge | th2 | 10 | | | ns | | 11 |
| Frequency, SCLK (32×fS, 48×fS, 64×fS) | fSCLKIN | 1.024 | | 12.288 | MHz | CL = 30 pF | 11 |
| LRCLK frequency | | 8 | 48 | 48 | kHz | | 11 |
| SCLK duty cycle | | 40 | 50 | 60 | % | | 11 |
| LRCLK duty cycle | | 40 | 50 | 60 | % | | 11 |
## CAD (KiCad official)
- Symbol: `TAS5731MPHPR`
- Footprint: `Package_QFP:TQFP-48-1EP_7x7mm_P0.5mm_EP5x5mm`
- 3D model: TQFP-48-EP(7x7) (KiCad packages3D, STEP)
- 3D model files: `tas5731mphpr-etched.step` / `tas5731mphpr-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `tas5731mphpr.step` / `tas5731mphpr.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/tas5731m) (71 pp, sha256 `b548f5b31dc8dd9b`, retrieved 2026-09-26, tier: lcsc)
- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.2`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-4-6` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/tas5731mphpr-datasheet.pdf)