component
STM8S001J3M3
Public Made by Adomby adom
STMicroelectronics Microcontrollers (MCU/MPU/SOC), SOP-8-150mil. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads on click. Unloads only if this page sits in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads on click. Unloads only if this page sits in the background.
PCB Footprint
Open full view ↗Loads on click. Unloads only if this page sits in the background.
Datasheet
Open in new tab ↗Loads on click. Unloads only if this page sits in the background.
README
markdownSTM8S001J3M3
STMicroelectronics · Microcontrollers (MCU/MPU/SOC) · SOP-8-150mil
STM8S001J3M3 from STMicroelectronics, in a SOP-8-150mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | PD6/AIN6/UART1_RX/PA1/OSCIN | bidirectional | Multiplexed I/O bonding PD6 and PA1 to one pad; default functions are Port D6 (high-sink push-pull, O3 speed), AIN6 analog input, UART1 receive data, and PA1 external HSE clock input (0-16 MHz); note PA1 is forced to weak-pull-up in halt/active-halt modes. |
| 2 | VSS/VSSA | power_in | Digital ground and analog ground reference; both VSS and VSSA are bonded to this pin and must always be connected to the external power supply. |
| 3 | VCAP | passive | External capacitor node for the internal 1.8 V main voltage regulator; requires CEXT 470-3300 nF with ESR ≤ 0.3 Ω at 1 MHz and ESL ≤ 15 nH connected between this pin and VSS. |
| 4 | VDD/VDDA | power_in | Main power supply (2.95 V to 5.5 V) and analog supply/reference for the ADC; both VDD and VDDA are bonded to this pin and must always be connected to the external power supply. |
| 5 | PA3/TIM2_CH3/PB5/I2C_SDA | bidirectional | Multiplexed I/O bonding PA3 (high-sink push-pull, O3 speed) and PB5 (true open-drain, no P-buffer or pull-up to VDD); default functions Port A3/B5 with TIM2_CH3 and I2C_SDA (up to 400 kHz); PA3 remappable to SPI_NSS [AFR1] or UART1_TX [AFR1+AFR0], PB5 remappable to TIM1_BKIN [AFR4]; VIN max on this pin is limited by the standard PA3 GPIO. |
| 6 | PB4/I2C_SCL | bidirectional | Bidirectional I/O for PB4 as true open-drain (no P-buffer, no pull-up to VDD, no protection diode to VDD); default function I2C clock (up to 400 kHz); remappable to ADC external trigger [AFR4]. |
| 7 | PC3/TIM1_CH3/PC4/CLK_CCO/TIM1_CH4/PC5/SPI_SCK | bidirectional | Multiplexed I/O bonding PC3, PC4, and PC5 to one pad (all high-sink push-pull, O3 speed); default functions Port C3/C4/C5 with TIM1_CH3, configurable clock output (CLK_CCO)/TIM1_CH4, and SPI_SCK; remappable to TLI [AFR3], AIN2 [AFR2], TIM2_CH1 [AFR0], TIM1_CH1N [AFR7], and TIM1_CH2N [AFR7]; push-pull configuration on any bonded GPIO affects all others on this pin. |
| 8 | PC6/SPI_MOSI/PD1/SWIM/PD3/AIN4/TIM2_CH2/PD5/AIN5/UART1_TX | bidirectional | Multiplexed I/O bonding PC6, PD1, PD3, and PD5 to one pad (all high-sink; PD1 O4 speed, others O3); PD1 is the SWIM single-wire debug interface and defaults to input pull-up during and after reset; other functions include SPI_MOSI, TIM1_CH1 [AFR0], AIN4/AIN5 analog inputs, TIM2_CH2, ADC_ETR, and UART1_TX; a ~5 s firmware delay before reassigning SWIM function is strongly recommended to allow reprogram access. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | SOP-8-150mil |
| Category | Embedded Processors & Controllers |
| Pins | 8 |
CAD (KiCad official)
- Symbol:
STM8S001J3M3 - Footprint:
Package_SO:SOIC-8_3.9x4.9mm_P1.27mm - 3D model: SOP-8-150mil (KiCad packages3D, STEP)
- 3D model files:
stm8s001j3m3-etched.step/stm8s001j3m3-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);stm8s001j3m3.step/stm8s001j3m3.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: STMicroelectronics datasheet (84 pp, sha256
64ae6cc93f3e51bc, retrieved 2026-09-26, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.2, primaryclaude-haiku-4-5-20251001(text), consensusclaude-sonnet-4-6(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).