main
Ray
Publish 0.1.0
ca0a60f
STM8L001J3M3
STMicroelectronics · Microcontrollers (MCU/MPU/SOC) · SOP-8-150mil
STM8L001J3M3 from STMicroelectronics, in a SOP-8-150mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | PA0/SWIM/BEEP/IR_TIM | bidirectional | PA0 is a high sink/source I/O with LED driver capability that serves as SWIM input/output, beep output and timer infrared output, and it is in input pull-up during reset; because pin 1 is shared, its pull-up state also affects PC3 and PC4 and the SWIM pin must be delayed (about 5 s in firmware) before switching to I/O mode. |
| 2 | PA2 (shared with PA4/TIM2_BKIN and PA6/COMP_REF) | bidirectional | PA2 is a high sink/source I/O on the shared pin 2, where PA4 provides the Timer 2 break input and PA6 provides the comparator external reference, and push-pull configuration of PA2 also affects PA4 and PA6. |
| 3 | VSS | power_in | Ground reference pin for the device (all voltages are referred to VSS). |
| 4 | VDD | power_in | Power supply pin; the standard operating voltage is 1.8 V to 3.6 V (VDD = VSS-referenced, absolute maximum external supply -0.3 V to 4.0 V). |
| 5 | PD0/TIM3_CH2/COMP1_CH3 (shared with PB3/TIM2_ETR/COMP2_CH2 and PB5/SPI_SCK) | bidirectional | Pin 5 is a high sink/source I/O that provides Port D0 as Timer 3 channel 2 or comparator 1 channel 3, Port B3 as Timer 2 trigger or comparator 2 channel 2, and Port B5 as SPI clock. |
| 6 | PB6/SPI_MOSI | bidirectional | Port B6 is a high sink/source I/O that serves as the SPI master output / slave input. |
| 7 | PB7/SPI_MISO (shared with PC0/I2C_SDA) | bidirectional | Port B7 is a high sink/source I/O used as SPI master input / slave output, and because pin 7 is shared with PC0/I2C_SDA (true open drain), its VIN maximum is limited by the standard GPIO PB7. |
| 8 | PC1/I2C_SCL (shared with PC2/USART_RX) | bidirectional | Port C1 is a true open-drain I/O used as I2C clock, and because pin 8 is shared with PC2/USART_RX its VIN maximum is limited by the standard GPIO PC2 (USART receive). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | SOP-8-150mil |
| Category | Embedded Processors & Controllers |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Voltage characteristics: external supply voltage | VDD-VSS | -0.3 | 4 | V | 31 | ||
| Total current into VDD power line (source) | IVDD | 80 | mA | 32 | |||
| Total current out of VSS ground line (sink) | IVSS | 80 | mA | 32 | |||
| Output current sunk by IR_TIM pin | IIO | 80 | mA | IR_TIM pin with high sink LED driver capability | 32 | ||
| Output current sunk by any other I/O and control pin | IIO | 25 | mA | any other I/O and control pin | 32 | ||
| Output current sourced by any I/Os and control pin | IIO | -25 | mA | sourced by any I/Os and control pin | 32 | ||
| Injected current on any pin | IINJ(PIN) | -5 | 5 | mA | 32 | ||
| Total injected current (sum of all I/O and control pins) | ΣIINJ(PIN) | -25 | 25 | mA | 32 | ||
| Storage temperature range | TSTG | -65 | 150 | °C | 32 | ||
| Maximum junction temperature | TJ | 150 | °C | 32 | |||
| Master clock frequency | fMASTER | 0 | 16 | MHz | 1.8 V ≤ VDD < 3.6 V | 32 | |
| Standard operating voltage | VDD | 1.8 | 3.6 | V | 32 | ||
| Power dissipation | PD | 49 | mW | TA = 125 °C, for suffix 3 devices, SO8N | 32 | ||
| Temperature range | TA | -40 | 125 | °C | 1.8 V ≤ VDD < 3.6 V (3 suffix version) | 32 | |
| Junction temperature range | TJ | -40 | 130 | °C | -40 °C ≤ TA ≤ 125 °C (3 suffix version) | 32 | |
| Power on reset threshold | VPOR | 1.35 | 1.65 | V | 33 | ||
| Power down reset threshold | VPDR | 1.4 | 1.6 | V | 33 | ||
| VDD rise time rate | tVDD | 20 | 1300 | µs/V | 33 | ||
| Supply current in Run mode | IDD (Run) | 0.39 | 0.6 | mA | Code executed from RAM, fMASTER = 2 MHz | 34 | |
| Supply current in Run mode | IDD (Run) | 0.55 | 0.7 | mA | Code executed from RAM, fMASTER = 4 MHz | 34 | |
| Supply current in Run mode | IDD (Run) | 0.9 | 1.2 | mA | Code executed from RAM, fMASTER = 8 MHz | 34 | |
| Supply current in Run mode | IDD (Run) | 1.6 | 2.1 | mA | Code executed from RAM, fMASTER = 16 MHz | 34 | |
| Supply current in Run mode | IDD (Run) | 0.88 | 1.8 | mA | Code executed from Flash, fMASTER = 4 MHz | 34 | |
| Supply current in Run mode | IDD (Run) | 1.5 | 2.5 | mA | Code executed from Flash, fMASTER = 8 MHz | 34 | |
| Supply current in Run mode | IDD (Run) | 2.7 | 3.5 | mA | Code executed from Flash, fMASTER = 16 MHz | 34 | |
| Supply current in Wait mode | IDD (Wait) | 245 | 400 | µA | CPU not clocked, all peripherals off, HSI internal RC osc., fMASTER = 2 MHz | 35 | |
| Supply current in Wait mode | IDD (Wait) | 300 | 450 | µA | CPU not clocked, all peripherals off, HSI internal RC osc., fMASTER = 4 MHz | 35 | |
| Supply current in Wait mode | IDD (Wait) | 380 | 600 | µA | CPU not clocked, all peripherals off, HSI internal RC osc., fMASTER = 8 MHz | 35 | |
| Supply current in Wait mode | IDD (Wait) | 510 | 800 | µA | CPU not clocked, all peripherals off, HSI internal RC osc., fMASTER = 16 MHz | 35 | |
| Supply current in Halt mode | IDD(Halt) | 0.35 | 1.2 | μA | TA = -40 °C to 25 °C | 36 | |
| Supply current in Halt mode | IDD(Halt) | 0.6 | 1.8 | μA | TA = 55 °C | 36 | |
| Supply current in Halt mode | IDD(Halt) | 1 | 2.5 | μA | TA = 85 °C | 36 | |
| Supply current in Halt mode | IDD(Halt) | 2.5 | 6.5 | μA | TA = 105 °C | 36 | |
| Supply current in Halt mode | IDD(Halt) | 5.4 | 12 | μA | TA = 125 °C | 36 | |
| Supply current in Active-halt mode | IDD(AH) | 0.8 | 2 | μA | LSI RC osc. (at 37 kHz), TA = -40 °C to 25 °C | 36 | |
| Supply current in Active-halt mode | IDD(AH) | 1 | 2.5 | μA | LSI RC osc. (at 37 kHz), TA = 55 °C | 36 | |
| Supply current in Active-halt mode | IDD(AH) | 1.4 | 3.2 | μA | LSI RC osc. (at 37 kHz), TA = 85 °C | 36 | |
| Supply current in Active-halt mode | IDD(AH) | 2.9 | 7.5 | μA | LSI RC osc. (at 37 kHz), TA = 105 °C | 36 | |
| Supply current in Active-halt mode | IDD(AH) | 5.8 | 13 | μA | LSI RC osc. (at 37 kHz), TA = 125 °C | 36 | |
| Wakeup time from Active-halt mode to Run mode | tWU(AH) | 4 | 6.5 | μs | fCPU = 16 MHz | 36 | |
| Wakeup time from Halt mode to Run mode | tWU(Halt) | 4 | 6.5 | μs | fCPU = 16 MHz | 36 | |
| Accuracy of HSI oscillator (factory calibrated) | ACCHSI | -2.5 | 2.5 | % | VDD = 3.0 V, TA = 25 °C | 37 | |
| Accuracy of HSI oscillator (factory calibrated) | ACCHSI | -5 | % | 1.8 V ≤ VDD ≤ 3.6 V, -40 °C ≤ TA ≤ 125 °C | 37 | ||
| HSI oscillator power consumption | IDD(HSI) | 70 | 100 | µA | 37 | ||
| LSI oscillator frequency | fLSI | 26 | 38 | 56 | kHz | 39 | |
| LSI oscillator frequency drift | fdrift(LSI) | -12 | 11 | % | 0 °C ≤ TA ≤ 85 °C | 39 | |
| Data retention mode | VRM | 1.65 | V | Flash memory Halt mode (or Reset) | 39 | ||
| Erase/write cycles (program memory) | NRW | 100 | cycles | See notes (1)(2) | 39 | ||
| Erase/write cycles (data memory) | NRW | 100 | kcycles | See notes (1)(3) | 39 | ||
| Data retention (program memory) | tRET | 20 | years | after 10k erase/write cycles at TA = +85 °C, TRET = 55 °C | 39 | ||
| Data retention (data memory) | tRET | 20 | years | after 10k erase/write cycles at TA = +85 °C, TRET = 55 °C | 39 | ||
| Input leakage current (standard I/Os) | Ilkg | 50 | nA | VSS ≤ VIN ≤ VDD | 40 | ||
| Weak pull-up equivalent resistor | RPU | 30 | 45 | 60 | kΩ | VIN = VSS | 40 |
| Output low level voltage for an I/O pin (high sink ports) | VOL | 0.45 | V | IIO = +2 mA, VDD = 3.0 V | 43 | ||
| Output low level voltage for an I/O pin (high sink ports) | VOL | 1.2 | V | IIO = +10 mA, VDD = 3.0 V | 43 | ||
| Output low level voltage for an I/O pin (true open drain ports) | VOL | 0.45 | V | IIO = +3 mA, VDD = 3.0 V | 43 | ||
| Output low level voltage for an I/O pin (PA0 high sink LED driver) | VOL | 0.9 | V | IIO = +20 mA, VDD = 2.0 V | 43 | ||
| Thermal resistance junction-ambient | ΘJA | 102 | °C/W | SO8N; JEDEC JESD51-2, 4-layer PCB, natural convection | 52 |
CAD (KiCad official)
- Symbol:
STM8L001J3M3 - Footprint:
Package_SO:SOIC-8_3.9x4.9mm_P1.27mm - 3D model: SOP-8-150mil (KiCad packages3D, STEP)
- 3D model files:
stm8l001j3m3-etched.step/stm8l001j3m3-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);stm8l001j3m3.step/stm8l001j3m3.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: STMicroelectronics datasheet (58 pp, sha256
477d3d595f6db0ec, retrieved 2026-11-10, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# STM8L001J3M3
**STMicroelectronics** · Microcontrollers (MCU/MPU/SOC) · SOP-8-150mil
STM8L001J3M3 from STMicroelectronics, in a SOP-8-150mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | PA0/SWIM/BEEP/IR_TIM | bidirectional | PA0 is a high sink/source I/O with LED driver capability that serves as SWIM input/output, beep output and timer infrared output, and it is in input pull-up during reset; because pin 1 is shared, its pull-up state also affects PC3 and PC4 and the SWIM pin must be delayed (about 5 s in firmware) before switching to I/O mode. |
| 2 | PA2 (shared with PA4/TIM2_BKIN and PA6/COMP_REF) | bidirectional | PA2 is a high sink/source I/O on the shared pin 2, where PA4 provides the Timer 2 break input and PA6 provides the comparator external reference, and push-pull configuration of PA2 also affects PA4 and PA6. |
| 3 | VSS | power_in | Ground reference pin for the device (all voltages are referred to VSS). |
| 4 | VDD | power_in | Power supply pin; the standard operating voltage is 1.8 V to 3.6 V (VDD = VSS-referenced, absolute maximum external supply -0.3 V to 4.0 V). |
| 5 | PD0/TIM3_CH2/COMP1_CH3 (shared with PB3/TIM2_ETR/COMP2_CH2 and PB5/SPI_SCK) | bidirectional | Pin 5 is a high sink/source I/O that provides Port D0 as Timer 3 channel 2 or comparator 1 channel 3, Port B3 as Timer 2 trigger or comparator 2 channel 2, and Port B5 as SPI clock. |
| 6 | PB6/SPI_MOSI | bidirectional | Port B6 is a high sink/source I/O that serves as the SPI master output / slave input. |
| 7 | PB7/SPI_MISO (shared with PC0/I2C_SDA) | bidirectional | Port B7 is a high sink/source I/O used as SPI master input / slave output, and because pin 7 is shared with PC0/I2C_SDA (true open drain), its VIN maximum is limited by the standard GPIO PB7. |
| 8 | PC1/I2C_SCL (shared with PC2/USART_RX) | bidirectional | Port C1 is a true open-drain I/O used as I2C clock, and because pin 8 is shared with PC2/USART_RX its VIN maximum is limited by the standard GPIO PC2 (USART receive). |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | SOP-8-150mil |
| Category | Embedded Processors & Controllers |
| Pins | 8 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Voltage characteristics: external supply voltage | VDD-VSS | -0.3 | | 4 | V | | 31 |
| Total current into VDD power line (source) | IVDD | | | 80 | mA | | 32 |
| Total current out of VSS ground line (sink) | IVSS | | | 80 | mA | | 32 |
| Output current sunk by IR_TIM pin | IIO | | | 80 | mA | IR_TIM pin with high sink LED driver capability | 32 |
| Output current sunk by any other I/O and control pin | IIO | | | 25 | mA | any other I/O and control pin | 32 |
| Output current sourced by any I/Os and control pin | IIO | | | -25 | mA | sourced by any I/Os and control pin | 32 |
| Injected current on any pin | IINJ(PIN) | -5 | | 5 | mA | | 32 |
| Total injected current (sum of all I/O and control pins) | ΣIINJ(PIN) | -25 | | 25 | mA | | 32 |
| Storage temperature range | TSTG | -65 | | 150 | °C | | 32 |
| Maximum junction temperature | TJ | | | 150 | °C | | 32 |
| Master clock frequency | fMASTER | 0 | | 16 | MHz | 1.8 V ≤ VDD < 3.6 V | 32 |
| Standard operating voltage | VDD | 1.8 | | 3.6 | V | | 32 |
| Power dissipation | PD | | | 49 | mW | TA = 125 °C, for suffix 3 devices, SO8N | 32 |
| Temperature range | TA | -40 | | 125 | °C | 1.8 V ≤ VDD < 3.6 V (3 suffix version) | 32 |
| Junction temperature range | TJ | -40 | | 130 | °C | -40 °C ≤ TA ≤ 125 °C (3 suffix version) | 32 |
| Power on reset threshold | VPOR | 1.35 | | 1.65 | V | | 33 |
| Power down reset threshold | VPDR | 1.4 | | 1.6 | V | | 33 |
| VDD rise time rate | tVDD | 20 | | 1300 | µs/V | | 33 |
| Supply current in Run mode | IDD (Run) | | 0.39 | 0.6 | mA | Code executed from RAM, fMASTER = 2 MHz | 34 |
| Supply current in Run mode | IDD (Run) | | 0.55 | 0.7 | mA | Code executed from RAM, fMASTER = 4 MHz | 34 |
| Supply current in Run mode | IDD (Run) | | 0.9 | 1.2 | mA | Code executed from RAM, fMASTER = 8 MHz | 34 |
| Supply current in Run mode | IDD (Run) | | 1.6 | 2.1 | mA | Code executed from RAM, fMASTER = 16 MHz | 34 |
| Supply current in Run mode | IDD (Run) | | 0.88 | 1.8 | mA | Code executed from Flash, fMASTER = 4 MHz | 34 |
| Supply current in Run mode | IDD (Run) | | 1.5 | 2.5 | mA | Code executed from Flash, fMASTER = 8 MHz | 34 |
| Supply current in Run mode | IDD (Run) | | 2.7 | 3.5 | mA | Code executed from Flash, fMASTER = 16 MHz | 34 |
| Supply current in Wait mode | IDD (Wait) | | 245 | 400 | µA | CPU not clocked, all peripherals off, HSI internal RC osc., fMASTER = 2 MHz | 35 |
| Supply current in Wait mode | IDD (Wait) | | 300 | 450 | µA | CPU not clocked, all peripherals off, HSI internal RC osc., fMASTER = 4 MHz | 35 |
| Supply current in Wait mode | IDD (Wait) | | 380 | 600 | µA | CPU not clocked, all peripherals off, HSI internal RC osc., fMASTER = 8 MHz | 35 |
| Supply current in Wait mode | IDD (Wait) | | 510 | 800 | µA | CPU not clocked, all peripherals off, HSI internal RC osc., fMASTER = 16 MHz | 35 |
| Supply current in Halt mode | IDD(Halt) | | 0.35 | 1.2 | μA | TA = -40 °C to 25 °C | 36 |
| Supply current in Halt mode | IDD(Halt) | | 0.6 | 1.8 | μA | TA = 55 °C | 36 |
| Supply current in Halt mode | IDD(Halt) | | 1 | 2.5 | μA | TA = 85 °C | 36 |
| Supply current in Halt mode | IDD(Halt) | | 2.5 | 6.5 | μA | TA = 105 °C | 36 |
| Supply current in Halt mode | IDD(Halt) | | 5.4 | 12 | μA | TA = 125 °C | 36 |
| Supply current in Active-halt mode | IDD(AH) | | 0.8 | 2 | μA | LSI RC osc. (at 37 kHz), TA = -40 °C to 25 °C | 36 |
| Supply current in Active-halt mode | IDD(AH) | | 1 | 2.5 | μA | LSI RC osc. (at 37 kHz), TA = 55 °C | 36 |
| Supply current in Active-halt mode | IDD(AH) | | 1.4 | 3.2 | μA | LSI RC osc. (at 37 kHz), TA = 85 °C | 36 |
| Supply current in Active-halt mode | IDD(AH) | | 2.9 | 7.5 | μA | LSI RC osc. (at 37 kHz), TA = 105 °C | 36 |
| Supply current in Active-halt mode | IDD(AH) | | 5.8 | 13 | μA | LSI RC osc. (at 37 kHz), TA = 125 °C | 36 |
| Wakeup time from Active-halt mode to Run mode | tWU(AH) | | 4 | 6.5 | μs | fCPU = 16 MHz | 36 |
| Wakeup time from Halt mode to Run mode | tWU(Halt) | | 4 | 6.5 | μs | fCPU = 16 MHz | 36 |
| Accuracy of HSI oscillator (factory calibrated) | ACCHSI | -2.5 | | 2.5 | % | VDD = 3.0 V, TA = 25 °C | 37 |
| Accuracy of HSI oscillator (factory calibrated) | ACCHSI | -5 | | | % | 1.8 V ≤ VDD ≤ 3.6 V, -40 °C ≤ TA ≤ 125 °C | 37 |
| HSI oscillator power consumption | IDD(HSI) | | 70 | 100 | µA | | 37 |
| LSI oscillator frequency | fLSI | 26 | 38 | 56 | kHz | | 39 |
| LSI oscillator frequency drift | fdrift(LSI) | -12 | | 11 | % | 0 °C ≤ TA ≤ 85 °C | 39 |
| Data retention mode | VRM | 1.65 | | | V | Flash memory Halt mode (or Reset) | 39 |
| Erase/write cycles (program memory) | NRW | 100 | | | cycles | See notes (1)(2) | 39 |
| Erase/write cycles (data memory) | NRW | 100 | | | kcycles | See notes (1)(3) | 39 |
| Data retention (program memory) | tRET | 20 | | | years | after 10k erase/write cycles at TA = +85 °C, TRET = 55 °C | 39 |
| Data retention (data memory) | tRET | 20 | | | years | after 10k erase/write cycles at TA = +85 °C, TRET = 55 °C | 39 |
| Input leakage current (standard I/Os) | Ilkg | | | 50 | nA | VSS ≤ VIN ≤ VDD | 40 |
| Weak pull-up equivalent resistor | RPU | 30 | 45 | 60 | kΩ | VIN = VSS | 40 |
| Output low level voltage for an I/O pin (high sink ports) | VOL | | | 0.45 | V | IIO = +2 mA, VDD = 3.0 V | 43 |
| Output low level voltage for an I/O pin (high sink ports) | VOL | | | 1.2 | V | IIO = +10 mA, VDD = 3.0 V | 43 |
| Output low level voltage for an I/O pin (true open drain ports) | VOL | | | 0.45 | V | IIO = +3 mA, VDD = 3.0 V | 43 |
| Output low level voltage for an I/O pin (PA0 high sink LED driver) | VOL | | | 0.9 | V | IIO = +20 mA, VDD = 2.0 V | 43 |
| Thermal resistance junction-ambient | ΘJA | | 102 | | °C/W | SO8N; JEDEC JESD51-2, 4-layer PCB, natural convection | 52 |
## CAD (KiCad official)
- Symbol: `STM8L001J3M3`
- Footprint: `Package_SO:SOIC-8_3.9x4.9mm_P1.27mm`
- 3D model: SOP-8-150mil (KiCad packages3D, STEP)
- 3D model files: `stm8l001j3m3-etched.step` / `stm8l001j3m3-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `stm8l001j3m3.step` / `stm8l001j3m3.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [STMicroelectronics datasheet](https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8588882490169151488) (58 pp, sha256 `477d3d595f6db0ec`, retrieved 2026-11-10, tier: lcsc)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/stm8l001j3m3-datasheet.pdf)