main
Download ZIP Propose a change
Made with KiCad 10.0 · needs KiCad 10.0 or later to open · KiCad file format 20260206
Name Last commit message Last updated
docs stm6600cs25dm6f: one-pass backfill (re-etched) · Ray
viewers stm6600cs25dm6f: viewers · Ray
package.json Publish 0.1.1 · Ray
page.json Publish 0.1.1 · Ray
README.md Initial commit: component/stm6600cs25dm6f · Ray
stm6600cs25dm6f-etched.fit.json stm6600cs25dm6f: one-pass backfill (re-etched) · Ray
stm6600cs25dm6f-etched.glb stm6600cs25dm6f: one-pass backfill (re-etched) · Ray
stm6600cs25dm6f-etched.step stm6600cs25dm6f: one-pass backfill (re-etched) · Ray
stm6600cs25dm6f-hero.glb stm6600cs25dm6f: one-pass backfill (re-etched) · Ray
stm6600cs25dm6f-hero.overlay.json stm6600cs25dm6f: one-pass backfill (re-etched) · Ray
stm6600cs25dm6f.glb Publish 0.1.0 · Ray
stm6600cs25dm6f.kicad_mod Publish 0.1.0 · Ray
stm6600cs25dm6f.kicad_sym Publish 0.1.0 · Ray
stm6600cs25dm6f.lbr Publish 0.1.0 · Ray
stm6600cs25dm6f.step Publish 0.1.0 · Ray

STM6600CS25DM6F

STMicroelectronics · Supervisor And Reset ICs · TDFN-12(2x3)

STM6600CS25DM6F from STMicroelectronics, in a TDFN-12(2x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VCC power_in Power supply input monitored during startup and normal operation; operating voltage range 1.6 V to 5.5 V; decoupling 0.1 µF capacitor required as close as possible to device.
2 SR input Smart Reset™ button input with factory-trimmed voltage threshold and ±8 kV HBM ESD protection; active low input connected to GND through momentary push-button; 100 kΩ optional internal pull-up resistor.
3 VREF power_out Precise 1.5 V voltage reference output with 1% accuracy; available after tREC expires; mandatory 1 µF external capacitor must be connected.
4 PSHOLD input Power supply hold input with factory-trimmed voltage detector threshold; driven high during startup to confirm proper power-up or low during operation to trigger shutdown; internal pull-down resistor during startup.
5 CSRD input Smart Reset™ delay time capacitive input; external capacitor to ground determines additional delay tSRD at approximately 10 s/µF; leave open if not used.
6 PB input Power-on push-button input with factory-trimmed voltage threshold and ±8 kV HBM ESD protection; active low input with internal 100 kΩ pull-up resistor; connected to GND through momentary push-button.
7 VCCLO output High threshold detection output; active low open drain pulled low when VCC below VTH+ during startup or when undervoltage detected during operation; requires 10 kΩ pull-up resistor; floating in standby mode.
8 PBOUT output Push-button status output; active low open drain reflecting PB input state after tDEBOUNCE debounce period; stays low minimum tINT_Min if PB held; requires 10 kΩ pull-up resistor.
9 EN output Enable output (active high for STM6600CS25DM6F); push-pull output asserted after valid power-up event and PSHOLD confirmation; deasserted by button release before PSHOLD confirmation, PSHOLD forced low, undervoltage detected, or long push (>tDEBOUNCE + tSRD).
10 RST output Reset output; active low open drain pulled low for tREC minimum 240 ms during power-up after PB falling edge and tDEBOUNCE; requires 10 kΩ pull-up resistor.
11 INT output Interrupt output; active low open drain asserted when PB pressed for tDEBOUNCE or more during normal operation or when VCC falls below VTH- threshold; held high during power-up; minimum pulse width tINT_Min; requires 10 kΩ pull-up resistor.
12 GND power_in Ground; device reference potential and application circuit return.
13 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer STMicroelectronics
Package TDFN-12(2x3)
Category Power Management (PMIC)
Pins 13

CAD (KiCad official)

  • Symbol: STM6600CS25DM6F
  • Footprint: Package_DFN_QFN:DFN-12-1EP_2x3mm_P0.45mm_EP0.64x2.4mm
  • 3D model: TDFN-12(2x3) (KiCad packages3D, STEP)
  • 3D model files: stm6600cs25dm6f-etched.step / stm6600cs25dm6f-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); stm6600cs25dm6f.step / stm6600cs25dm6f.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: STMicroelectronics datasheet (52 pp, sha256 24305a688f436ae9, retrieved 2026-10-03, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-4-5-20251001 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF