STM6600AS24DM6F

{
  "slug": "stm6600as24dm6f",
  "version": "0.1.0",
  "type": "component",
  "description": "STMicroelectronics Supervisor And Reset ICs, TDFN-12(2x3). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",
  "tags": [
    "component",
    "power management (pmic)",
    "stm6600as24dm6f",
    "factory-2.0.0",
    "extractor-text"
  ],
  "dependencies": {},
  "hero": {
    "type": "image",
    "path": "docs/hero.png"
  },
  "files": [
    "page.json",
    "README.md",
    "stm6600as24dm6f.kicad_sym",
    "stm6600as24dm6f.kicad_mod",
    "stm6600as24dm6f.glb",
    "stm6600as24dm6f.step",
    "stm6600as24dm6f.lbr",
    "docs/hero.png",
    "docs/stm6600as24dm6f-datasheet.pdf",
    "viewers/symbol.html",
    "viewers/footprint.html",
    "stm6600as24dm6f-hero.glb",
    "stm6600as24dm6f-hero.overlay.json",
    "stm6600as24dm6f-etched.glb"
  ],
  "component": {
    "mpn": "STM6600AS24DM6F",
    "manufacturer": "STMicroelectronics",
    "package": "TDFN-12(2x3)",
    "pin_count": 13,
    "category": "Power Management (PMIC)",
    "subcategory": "Supervisor And Reset ICs",
    "datasheet": "https://www.st.com/resource/en/datasheet/stm6600as24dm6f.pdf",
    "parts": {
      "symbol": "stm6600as24dm6f.kicad_sym",
      "footprint": "stm6600as24dm6f.kicad_mod",
      "model_3d": "stm6600as24dm6f-hero.glb",
      "model_3d_plain": "stm6600as24dm6f-etched.glb",
      "model_3d_step": "stm6600as24dm6f-etched.step",
      "model_3d_step_plain": "stm6600as24dm6f.step",
      "lbr": "stm6600as24dm6f.lbr"
    },
    "distributor_links": {
      "lcsc": "C2067186",
      "digikey": "497-10548-2-ND",
      "mouser": "511-STM6600AS24DM6F"
    },
    "distributor_check": {
      "checked_at": "2026-11-06T01:08:34Z",
      "source": "Component Ocean /api/assign-pns",
      "digikey": {
        "pn": "497-10548-2-ND",
        "status": "found"
      },
      "mouser": {
        "pn": "511-STM6600AS24DM6F",
        "status": "found"
      }
    },
    "pins": [
      {
        "number": "1",
        "name": "VCC",
        "type": "power_in",
        "description": "Power supply input that is monitored during startup and normal operation and should be decoupled to ground with a 0.1 µF capacitor placed as close to the device as possible."
      },
      {
        "number": "2",
        "name": "SR",
        "type": "input",
        "description": "Smart Reset button input with ±8 kV HBM ESD protection that must be held together with PB for tSRD to recognize a long push and must not be grounded permanently."
      },
      {
        "number": "3",
        "name": "VREF",
        "type": "power_out",
        "description": "Precise 1.5 V voltage reference with 1% accuracy that requires a mandatory 1 µF capacitor even when unused and is disabled in standby mode."
      },
      {
        "number": "4",
        "name": "PSHOLD",
        "type": "input",
        "description": "Power supply hold input compared to an accurate reference, where a high level during power-up confirms start-up and a low level during normal operation deasserts the enable output."
      },
      {
        "number": "5",
        "name": "CSRD",
        "type": "passive",
        "description": "Adjustable Smart Reset delay input where a capacitor to ground sets the additional delay tSRD, and the pin is left open if no capacitor is used."
      },
      {
        "number": "6",
        "name": "PB",
        "type": "input",
        "description": "Power-on push-button input with ±8 kV HBM ESD protection that must switch to GND, has an internal 100 kΩ pull-up, and requires VCC above VTH+ for the whole tDEBOUNCE period to power up."
      },
      {
        "number": "7",
        "name": "VCCLO",
        "type": "output",
        "description": "High-threshold detection output that is active low and open drain by default, requires a pull-up resistor (10 kΩ is sufficient in most applications), and is low when VCC is below VTH+."
      },
      {
        "number": "8",
        "name": "PBOUT",
        "type": "output",
        "description": "Status output of the PB input that is active low and open drain by default, requires a pull-up resistor, and stays low for at least tINT_Min after a valid push-button press."
      },
      {
        "number": "9",
        "name": "EN",
        "type": "output",
        "description": "Active high enable output in push-pull that is asserted after a valid turn-on event to enable system power and is released low on the defined power-down conditions."
      },
      {
        "number": "10",
        "name": "RST",
        "type": "output",
        "description": "Active low open-drain reset output that is pulled low for tREC during startup and after a valid long push on this variant, and requires a pull-up resistor."
      },
      {
        "number": "11",
        "name": "INT",
        "type": "output",
        "description": "Active low open-drain interrupt output that is asserted for at least tINT_Min on a push-button press held for tDEBOUNCE or on undervoltage, and requires a pull-up resistor."
      },
      {
        "number": "12",
        "name": "GND",
        "type": "power_in",
        "description": "Ground reference for the device."
      },
      {
        "number": "13",
        "name": "EP",
        "type": "passive",
        "description": "Exposed pad (from the footprint; not named in the datasheet pin table)."
      }
    ],
    "provenance": {
      "extractor": "extract_pins 0.3",
      "factory_chain": {
        "factory": "2.0.0",
        "extractor": "extract_pins 0.3",
        "primary_model": "claude-haiku-5-5",
        "primary_mode": "text",
        "consensus_model": "claude-sonnet-5-5",
        "consensus": "agreed",
        "guards": "pin_guards 0.1: passed",
        "guard_notes": [],
        "pages_sent": 23,
        "cost_usd": 0.0286,
        "at": "2026-11-06T01:08:05"
      },
      "datasheet": {
        "url": "https://www.st.com/resource/en/datasheet/stm6600as24dm6f.pdf",
        "pages": 52,
        "sha256": "24305a688f436ae9",
        "source_tier": "mfr"
      },
      "cad": "KiCad official (CC-BY-SA 4.0)",
      "pins": {
        "total": 13,
        "described": 13,
        "cites_pages": true,
        "refuses_to_fabricate": true
      }
    },
    "viewers": {
      "symbol": "viewers/symbol.html",
      "footprint": "viewers/footprint.html"
    },
    "models_3d": [
      {
        "file": "stm6600as24dm6f.step",
        "role": "plain",
        "up": "Z",
        "units": "mm",
        "origin": "footprint origin = pad-pattern centre",
        "seat": "z = 0",
        "extents_mm": [
          2.0,
          2.98,
          0.77
        ],
        "zmin_mm": 0.0,
        "centre_offset_mm": 0.0,
        "footprint_binding": "identity",
        "sha256": "b31bd9302d4b25b31a41a44a286ba9e7e6890d59fdd9ec15b16dc263ab0a306f",
        "checked": "2026-11-06",
        "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"
      },
      {
        "file": "stm6600as24dm6f-etched.step",
        "role": "eda",
        "up": "Z",
        "units": "mm",
        "origin": "footprint origin = pad-pattern centre",
        "seat": "z = 0",
        "extents_mm": [
          2.0,
          2.98,
          0.77
        ],
        "zmin_mm": 0.0,
        "centre_offset_mm": 0.0,
        "footprint_binding": "identity",
        "sha256": "627552d9f94e2301a8e02b84a8c23281a40e8fa98a8e4c6aa1187ab7f0f4165d",
        "checked": "2026-11-06",
        "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"
      }
    ]
  }
}