Generated by kicad-footprint-generator · KiCad file format 20260206
STM32U595RJT6Q
STMicroelectronics · IC · LQFP-64(10x10)
STM32U595RJT6Q from STMicroelectronics, in a LQFP-64(10x10). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model, then checked against ST open pin data); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VBAT | power_in | Backup domain supply for RTC, 32 x 32-bit backup registers and 2-Kbyte backup SRAM in VBAT mode. |
| 2 | PC13 | bidirectional | FT I/O supplied via the VSW power switch (3 mA max sink), output speed must not exceed 2 MHz with max 30 pF load; AF: EVENTOUT; additional: WKUP2, RTC_TS/RTC_OUT1, TAMP_IN1/TAMP_OUT2. |
| 3 | PC14-OSC32_IN | bidirectional | FT_o I/O (PC14 after reset) supplied via VSW switch, not to be used as current source; additional function OSC32_IN (LSE crystal input). |
| 4 | PC15-OSC32_OUT | bidirectional | FT_o I/O (PC15 after reset) supplied via VSW switch, not to be used as current source; additional function OSC32_OUT (LSE crystal output). |
| 5 | PH0-OSC_IN | bidirectional | FT I/O (PH0 after reset) with additional function OSC_IN (HSE oscillator input). |
| 6 | PH1-OSC_OUT | bidirectional | FT I/O (PH1 after reset) with additional function OSC_OUT (HSE oscillator output). |
| 7 | NRST | bidirectional | Bidirectional reset pin (RST structure) with embedded weak pull-up resistor. |
| 8 | PC0 | bidirectional | FT_fha I/O; AF: LPTIM1_IN1, I2C3_SCL, LPUART1_RX, SDMMC1_D5 and others; additional: ADC1_IN1, ADC2_IN1, ADC4_IN1. |
| 9 | PC1 | bidirectional | FT_fhav I/O; AF: LPTIM1_CH1, SPI2_MOSI, I2C3_SDA, LPUART1_TX, SAI1_SD_A and others; additional: ADC1_IN2, ADC2_IN2, ADC4_IN2. |
| 10 | PC2 | bidirectional | FT_ha I/O; AF: LPTIM1_IN2, SPI2_MISO, MDF1_CCK1, USART6_RX; additional: ADC1_IN3, ADC2_IN3, ADC4_IN3. |
| 11 | PC3 | bidirectional | FT_ha I/O; AF: LPTIM1_ETR, SPI2_MOSI, USART6_TX, SAI1_SD_A; additional: ADC1_IN4, ADC2_IN4, ADC4_IN4. |
| 12 | VSSA | power_in | Analog ground for ADCs, DACs, OPAMPs, COMPs and VREFBUF. |
| 13 | VDDA | power_in | Analog supply for ADCs, DACs, OPAMPs, COMPs and VREFBUF (VREF+ is not a separate pin on this package). |
| 14 | PA0 | bidirectional | FT_hat I/O; AF: TIM2_CH1, TIM5_CH1, USART2_CTS, UART4_TX; additional: OPAMP1_VINP, ADC1_IN5, ADC2_IN5, WKUP1, TAMP_IN2/TAMP_OUT1. |
| 15 | PA1 | bidirectional | FT_hat I/O; AF: LPTIM1_CH2, TIM2_CH2, SPI1_SCK, USART2_RTS_DE, UART4_RX; additional: OPAMP1_VINM, ADC1_IN6, ADC2_IN6, WKUP3, TAMP_IN5/TAMP_OUT4. |
| 16 | PA2 | bidirectional | FT_ha I/O; AF: TIM2_CH3, USART2_TX (boot), LPUART1_TX; additional: COMP1_INP3, ADC1_IN7, ADC2_IN7, WKUP4/LSCO. |
| 17 | PA3 | bidirectional | TT_hav I/O; AF: TIM2_CH4, USART2_RX (boot), LPUART1_RX, SAI1_CK1; additional: OPAMP1_VOUT, ADC1_IN8, ADC2_IN8, WKUP5. |
| 18 | VSS | power_in | Digital ground. |
| 19 | VDD | power_in | Digital supply voltage. |
| 20 | PA4 | bidirectional | TT_ha I/O; AF: SPI1_NSS (boot), SPI3_NSS, USART2_CK, DCMI_HSYNC; additional: ADC1_IN9, ADC2_IN9, ADC4_IN9, DAC1_OUT1, WKUP2. |
| 21 | PA5 | bidirectional | TT_a I/O; AF: TIM2_CH1, TIM8_CH1N, SPI1_SCK (boot), USART3_RX; additional: ADC1_IN10, ADC2_IN10, ADC4_IN10, DAC1_OUT2, WKUP6. |
| 22 | PA6 | bidirectional | FT_ha I/O; AF: TIM1_BKIN, TIM3_CH1, SPI1_MISO (boot), USART3_CTS, LPUART1_CTS; additional: OPAMP2_VINP, ADC1_IN11, ADC2_IN11, ADC4_IN11, WKUP7. |
| 23 | PA7 | bidirectional | FT_fha I/O; AF: TIM1_CH1N, TIM3_CH2, I2C3_SCL, SPI1_MOSI (boot), USART3_TX; additional: OPAMP2_VINM, ADC1_IN12, ADC2_IN12, ADC4_IN20, WKUP8. |
| 24 | PB0 | bidirectional | TT_ha I/O; AF: TIM1_CH2N, TIM3_CH3, LPTIM3_CH1, SPI1_NSS, USART3_CK, COMP1_OUT; additional: OPAMP2_VOUT, ADC1_IN15, ADC2_IN15, ADC4_IN18. |
| 25 | PB1 | bidirectional | FT_ha I/O; AF: TIM1_CH3N, TIM3_CH4, LPTIM3_CH2, MDF1_SDI0, USART3_RTS_DE; additional: COMP1_INM1, ADC1_IN16, ADC2_IN16, ADC4_IN19, WKUP4. |
| 26 | PB2 | bidirectional | FT_hat I/O; AF: LPTIM1_CH1, I2C3_SMBA, SPI1_RDY, MDF1_CKI0; additional: COMP1_INP2, ADC1_IN17, ADC2_IN17, WKUP1, RTC_OUT2. |
| 27 | PB10 | bidirectional | FT_fhv I/O; AF: TIM2_CH3, LPTIM3_CH1, I2C4_SCL, I2C2_SCL (boot), SPI2_SCK, USART3_TX, LPUART1_RX, COMP1_OUT; additional: WKUP8. |
| 28 | VLXSMPS | passive | SMPS step-down converter switching output, connected through an external 2.2 µH inductor (ISAT > 0.5 A, DCR < 200 mΩ) to the VDD11 pins. |
| 29 | VDDSMPS | power_in | SMPS step-down converter supply input, requiring a 10 µF ±20% (ESR < 10 mΩ at 3 MHz, rated ≥ 10 V) capacitor. |
| 30 | VSSSMPS | power_in | SMPS step-down converter ground. |
| 31 | VDD11 | power_in | 1.1 V VCORE supply fed by the filtered SMPS output (or LDO), needing 2 × 2.2 µF ±20% (ESR < 20 mΩ at 3 MHz, rated ≥ 10 V) across the VDD11 pins. |
| 32 | VSS | power_in | Digital ground. |
| 33 | VDD | power_in | Digital supply voltage. |
| 34 | PB13 | bidirectional | FT_fa I/O; AF: TIM1_CH1N, LPTIM3_IN1, I2C2_SCL, SPI2_SCK (boot), USART3_CTS, LPUART1_CTS, SAI2_SCK_A. |
| 35 | PB14 | bidirectional | FT_fda I/O; AF: TIM1_CH2N, I2C2_SDA, SPI2_MISO (boot), USART3_RTS_DE, SDMMC2_D0; additional: UCPD1_DBCC2 (dead battery control). |
| 36 | PB15 | bidirectional | FT_c I/O; AF: RTC_REFIN, TIM1_CH3N, SPI2_MOSI (boot), SDMMC2_D1; additional: UCPD1_CC2, WKUP7; UCPD pull-down Rd 5.1 kΩ may be active after reset. |
| 37 | PC6 | bidirectional | FT_a I/O; AF: TIM3_CH1, TIM8_CH1, MDF1_CKI3, LCD_R0, SDMMC1_D0DIR, DCMI_D0, SAI2_MCLK_A. |
| 38 | PC7 | bidirectional | FT_a I/O; AF: TIM3_CH2, TIM8_CH2, MDF1_SDI3, LCD_R1, SDMMC1_D123DIR, DCMI_D1, SAI2_MCLK_B. |
| 39 | PC8 | bidirectional | FT_a I/O; AF: TIM3_CH3, TIM8_CH3, USART6_RX, SDMMC1_D0, LPTIM3_CH1. |
| 40 | PC9 | bidirectional | FT_a I/O; AF: TIM3_CH4, TIM8_CH4, USART6_TX, SDMMC1_D1, LPTIM3_CH2, TRACED0. |
| 41 | PA8 | bidirectional | FT_hv I/O; AF: MCO, TIM1_CH1, SPI1_RDY, USART1_CK, OTG_HS_SOF, SAI1_SCK_A. |
| 42 | PA9 | bidirectional | FT_u I/O; AF: TIM1_CH2, SPI2_SCK, USART1_TX (boot), SAI1_FS_A; additional: OTG_HS_VBUS. |
| 43 | PA10 | bidirectional | FT_u I/O; AF: CRS_SYNC, TIM1_CH3, USART1_RX (boot), OTG_HS_ID, SAI1_SD_A. |
| 44 | PA11 | bidirectional | TT I/O, 5V-tolerant when USB PHY is powered; AF: TIM1_CH4, SPI1_MISO, USART1_CTS, FDCAN1_RX; additional: OTG_HS_DM (boot). |
| 45 | PA12 | bidirectional | TT I/O, 5V-tolerant when USB PHY is powered; AF: TIM1_ETR, SPI1_MOSI, USART1_RTS_DE, FDCAN1_TX; additional: OTG_HS_DP (boot). |
| 46 | PA13 | bidirectional | FT I/O configured as JTMS/SWDIO after reset with internal pull-up active; AF: IR_OUT, SAI1_SD_B. |
| 47 | VSS | power_in | Digital ground. |
| 48 | VDDUSB | power_in | Independent USB transceiver supply. |
| 49 | PA14 | bidirectional | FT I/O configured as JTCK/SWCLK after reset with internal pull-down active; AF: LPTIM1_CH1, I2C1_SMBA, OTG_HS_SOF. |
| 50 | PA15 (JTDI) | bidirectional | FT_c I/O configured as JTDI after reset with internal pull-up active; AF: TIM2_CH1, SPI1_NSS, USART2_RX; additional: UCPD1_CC1 (Rd 5.1 kΩ pull-down may be active after reset). |
| 51 | PC10 | bidirectional | FT_a I/O; AF: SPI3_SCK, USART3_TX (boot), UART4_TX, SDMMC1_D2, SAI2_SCK_B, TRACED1. |
| 52 | PC11 | bidirectional | FT_ha I/O; AF: SPI3_MISO, USART3_RX (boot), UART4_RX, SDMMC1_D3, SAI2_MCLK_B. |
| 53 | PC12 | bidirectional | FT_hav I/O; AF: SPI3_MOSI, USART3_CK, UART5_TX, SDMMC1_CK, SAI2_SD_B, TRACED3. |
| 54 | PD2 | bidirectional | FT I/O; AF: TIM3_ETR, USART3_RTS_DE, UART5_RX, SDMMC1_CMD, TRACED2. |
| 55 | PB3 | bidirectional | FT_fa I/O configured as JTDO/TRACESWO after reset; AF: TIM2_CH2, I2C1_SDA, SPI1_SCK, SPI3_SCK; additional: COMP2_INM2. |
| 56 | PB4 (NJTRST) | bidirectional | FT_fa I/O configured as NJTRST after reset with internal pull-up active; AF: TIM3_CH1, I2C3_SDA, SPI1_MISO, SPI3_MISO; additional: COMP2_INP1. |
| 57 | PB5 | bidirectional | FT_havc I/O; AF: TIM3_CH2, I2C1_SMBA, SPI1_MOSI, SPI3_MOSI (boot), UART5_CTS; additional: UCPD1_DBCC1, WKUP6. |
| 58 | PB6 | bidirectional | FT_fa I/O; AF: TIM4_CH1, I2C1_SCL (boot), I2C4_SCL, USART1_TX; additional: COMP2_INP2, WKUP3. |
| 59 | PB7 | bidirectional | FT_fhav I/O; AF: TIM4_CH2, I2C1_SDA (boot), I2C4_SDA, USART1_RX, UART4_CTS; additional: COMP2_INM1, PVD_IN, WKUP4. |
| 60 | PH3-BOOT0 | input | FT I/O (PH3) that serves as BOOT0 boot mode selection input; AF: EVENTOUT. |
| 61 | PB8 | bidirectional | FT_f I/O; AF: TIM4_CH3, I2C1_SCL, SDMMC1_CKIN, FDCAN1_RX (boot), SAI1_MCLK_A; additional: WKUP5. |
| 62 | VDD11 | power_in | 1.1 V VCORE supply fed by the filtered SMPS output (or LDO), needing 2 × 2.2 µF ±20% (ESR < 20 mΩ at 3 MHz, rated ≥ 10 V) across the VDD11 pins. |
| 63 | VSS | power_in | Digital ground. |
| 64 | VDD | power_in | Digital supply voltage. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | LQFP-64(10x10) |
| Category | |
| Pins | 64 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| External main supply voltage (VDDSMPS, VDDA, VDDUSB, VDDDSI, VBAT, VREF+) | VDDX - VSS | -0.3 | 4 | V | 181 | ||
| I/O supply when HSLV = 0 | VDDIOx - VSS | -0.3 | 4 | V | HSLV = 0 | 181 | |
| I/O supply when HSLV = 1 | VDDIOx - VSS | -0.3 | 2.75 | V | HSLV = 1 | 181 | |
| Input voltage on FT_c pins | VIN | 5.5 | V | FT_c pins | 181 | ||
| Input voltage on any other pins | VIN | 4 | V | any other pins | 181 | ||
| Allowed voltage difference for VREF+ > VDDA | VREF+ - VDDA | 0.4 | V | VREF+ > VDDA | 181 | ||
| Variations between different VDDx power pins of the same domain | /ΔVDDx/ | 50 | mV | 181 | |||
| Variations between all the different ground pins | /VSSx-VSS/ | 50 | mV | including VREF- pin | 181 | ||
| Storage temperature range | TSTG | -65 | 150 | °C | 182 | ||
| Maximum junction temperature | TJ | 140 | °C | 182 | |||
| Total current into sum of all VDD power lines (source) | ∑IVDD | 200 | mA | 182 | |||
| Total current out of sum of all VSS ground lines (sink) | ∑IVSS | 200 | mA | 182 | |||
| Maximum current into each VDD power pin (source) | IVDD | 100 | mA | 182 | |||
| Maximum current out of each VSS ground pin (sink) | IVSS | 100 | mA | 182 | |||
| Output current sunk by any I/O and control pin | IIO | 20 | mA | sunk | 182 | ||
| Output current sourced by any I/O and control pin | IIO | 20 | mA | sourced | 182 | ||
| Total output current sunk by sum of all I/Os and control pins | ∑I(PIN) | 120 | mA | sunk | 182 | ||
| Total output current sourced by sum of all I/Os and control pins | ∑I(PIN) | 120 | mA | sourced | 182 | ||
| Injected current on FT_xx, TT_xx, RST pins | IINJ(PIN) | -5 | 0 | mA | FT_xx, TT_xx, RST pins | 182 | |
| Total injected current (sum of all I/Os and control pins) | ∑/IINJ(PIN)/ | 25 | mA | 182 | |||
| Standard operating voltage | VDD | 1.71 | 3.6 | V | IO_VDD_HSLV = 0 | 183 | |
| Standard operating voltage | VDD | 1.71 | 2.7 | V | IO_VDD_HSLV = 1 | 183 | |
| Supply voltage for PG[15:2] I/Os | VDDIO2 | 1.08 | 3.6 | V | At least one I/O in PG[15:2] used, IO_VDDIO2_HSLV = 0 | 183 | |
| Supply voltage for PG[15:2] I/Os | VDDIO2 | 1.08 | 2.7 | V | At least one I/O in PG[15:2] used, IO_VDDIO2_HSLV = 1 | 183 | |
| Supply voltage for PG[15:2] I/Os | VDDIO2 | 0 | 3.6 | V | PG[15:2] I/Os not used | 183 | |
| USB supply voltage | VDDUSB | 3 | 3.6 | V | USB used | 183 | |
| USB supply voltage | VDDUSB | 0 | 3.6 | V | USB not used | 183 | |
| Analog supply voltage | VDDA | 1.58 | 3.6 | V | COMP used | 183 | |
| Analog supply voltage | VDDA | 1.6 | 3.6 | V | DAC or OPAMP used | 183 | |
| Analog supply voltage | VDDA | 1.62 | 3.6 | V | ADC used | 183 | |
| Analog supply voltage | VDDA | 1.8 | 3.6 | V | VREFBUF used (normal mode) | 183 | |
| Analog supply voltage | VDDA | 0 | 3.6 | V | ADC, DAC, COMP, OPAMP, and VREFBUF not used | 183 | |
| Backup domain supply voltage | VBAT | 1.65 | 3.6 | V | 183 | ||
| I/O input voltage | VIN | -0.3 | 5 | V | FT_c I/Os | 183 | |
| I/O input voltage | VIN | -0.3 | V | TT_xx I/Os | 183 | ||
| Sum of output current sourced by all I/Os powered by VSW | IIO_SW | 3 | mA | 183 | |||
| Internal regulator ON, Range 1 VCORE | VCORE | 1.15 | 1.21 | 1.27 | V | Range 1 | 184 |
| Internal regulator ON, Range 2 VCORE | VCORE | 1.05 | 1.1 | 1.15 | V | Range 2 | 184 |
| Internal regulator ON, Range 3 VCORE | VCORE | 0.95 | 1 | 1.05 | V | Range 3 | 184 |
| Internal regulator ON, Range 4 VCORE | VCORE | 0.81 | 0.9 | 0.99 | V | Range 4 | 184 |
| AHB clock frequency | fHCLK | 160 | MHz | Range 1 | 184 | ||
| AHB clock frequency | fHCLK | 110 | MHz | Range 2 | 184 | ||
| AHB clock frequency | fHCLK | 55 | MHz | Range 3 | 184 | ||
| AHB clock frequency | fHCLK | 25 | MHz | Range 4 | 184 | ||
| APB1, APB2, APB3 clock frequency | fPCLKx (x = 1, 2, 3) | 160 | MHz | Range 1 | 184 | ||
| APB1, APB2, APB3 clock frequency | fPCLKx (x = 1, 2, 3) | 110 | MHz | Range 2 | 184 | ||
| APB1, APB2, APB3 clock frequency | fPCLKx (x = 1, 2, 3) | 55 | MHz | Range 3 | 184 | ||
| APB1, APB2, APB3 clock frequency | fPCLKx (x = 1, 2, 3) | 25 | MHz | Range 4 | 184 | ||
| Ambient temperature for suffix 6, maximum power dissipation | TA | -40 | 85 | °C | Maximum power dissipation | 184 | |
| Ambient temperature for suffix 6, low-power dissipation | TA | -40 | 105 | °C | Low-power dissipation | 184 | |
| Junction temperature range, suffix 6 version | TJ | -40 | 105 | °C | Suffix 6 version | 185 | |
| VDD fall-time rate | tVDD | 20 | µs/V | ULPMEN = 0 (default value) | 185 | ||
| Internal reference voltage | VREFINT | 1.175 | 1.215 | 1.255 | V | Range 1, 2, 3 | 188 |
| Average temperature coefficient | TCoeff | 40 | 125 | ppm/°C | -40°C < TJ < +130 °C | 188 | |
| Average voltage coefficient | VDDCoeff | 500 | 2900 | ppm/V | 3.0 V ≤ VDD ≤ 3.6 V | 188 | |
| Brownout reset threshold 0 rising edge | VBOR0 | 1.6 | 1.66 | 1.71 | V | Rising edge | 186 |
| Brownout reset threshold 0 falling edge | VBOR0 | 1.58 | 1.64 | 1.69 | V | Falling edge, range 1, 2, 3 | 186 |
CAD (KiCad official)
- Symbol:
STM32U595RJT6Q - Footprint:
Package_QFP:LQFP-64_10x10mm_P0.5mm - 3D model: LQFP-64(10x10) (KiCad packages3D, STEP)
- 3D model files:
stm32u595rjt6q-etched.step/stm32u595rjt6q-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);stm32u595rjt6q.step/stm32u595rjt6q.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: STMicroelectronics datasheet (385 pp, sha256
1a6951f7fcbc7a72, retrieved 2026-11-09, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).