Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

STM32U595RJT6Q

STMicroelectronics · IC · LQFP-64(10x10)

STM32U595RJT6Q from STMicroelectronics, in a LQFP-64(10x10). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model, then checked against ST open pin data); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VBAT power_in Backup domain supply for RTC, 32 x 32-bit backup registers and 2-Kbyte backup SRAM in VBAT mode.
2 PC13 bidirectional FT I/O supplied via the VSW power switch (3 mA max sink), output speed must not exceed 2 MHz with max 30 pF load; AF: EVENTOUT; additional: WKUP2, RTC_TS/RTC_OUT1, TAMP_IN1/TAMP_OUT2.
3 PC14-OSC32_IN bidirectional FT_o I/O (PC14 after reset) supplied via VSW switch, not to be used as current source; additional function OSC32_IN (LSE crystal input).
4 PC15-OSC32_OUT bidirectional FT_o I/O (PC15 after reset) supplied via VSW switch, not to be used as current source; additional function OSC32_OUT (LSE crystal output).
5 PH0-OSC_IN bidirectional FT I/O (PH0 after reset) with additional function OSC_IN (HSE oscillator input).
6 PH1-OSC_OUT bidirectional FT I/O (PH1 after reset) with additional function OSC_OUT (HSE oscillator output).
7 NRST bidirectional Bidirectional reset pin (RST structure) with embedded weak pull-up resistor.
8 PC0 bidirectional FT_fha I/O; AF: LPTIM1_IN1, I2C3_SCL, LPUART1_RX, SDMMC1_D5 and others; additional: ADC1_IN1, ADC2_IN1, ADC4_IN1.
9 PC1 bidirectional FT_fhav I/O; AF: LPTIM1_CH1, SPI2_MOSI, I2C3_SDA, LPUART1_TX, SAI1_SD_A and others; additional: ADC1_IN2, ADC2_IN2, ADC4_IN2.
10 PC2 bidirectional FT_ha I/O; AF: LPTIM1_IN2, SPI2_MISO, MDF1_CCK1, USART6_RX; additional: ADC1_IN3, ADC2_IN3, ADC4_IN3.
11 PC3 bidirectional FT_ha I/O; AF: LPTIM1_ETR, SPI2_MOSI, USART6_TX, SAI1_SD_A; additional: ADC1_IN4, ADC2_IN4, ADC4_IN4.
12 VSSA power_in Analog ground for ADCs, DACs, OPAMPs, COMPs and VREFBUF.
13 VDDA power_in Analog supply for ADCs, DACs, OPAMPs, COMPs and VREFBUF (VREF+ is not a separate pin on this package).
14 PA0 bidirectional FT_hat I/O; AF: TIM2_CH1, TIM5_CH1, USART2_CTS, UART4_TX; additional: OPAMP1_VINP, ADC1_IN5, ADC2_IN5, WKUP1, TAMP_IN2/TAMP_OUT1.
15 PA1 bidirectional FT_hat I/O; AF: LPTIM1_CH2, TIM2_CH2, SPI1_SCK, USART2_RTS_DE, UART4_RX; additional: OPAMP1_VINM, ADC1_IN6, ADC2_IN6, WKUP3, TAMP_IN5/TAMP_OUT4.
16 PA2 bidirectional FT_ha I/O; AF: TIM2_CH3, USART2_TX (boot), LPUART1_TX; additional: COMP1_INP3, ADC1_IN7, ADC2_IN7, WKUP4/LSCO.
17 PA3 bidirectional TT_hav I/O; AF: TIM2_CH4, USART2_RX (boot), LPUART1_RX, SAI1_CK1; additional: OPAMP1_VOUT, ADC1_IN8, ADC2_IN8, WKUP5.
18 VSS power_in Digital ground.
19 VDD power_in Digital supply voltage.
20 PA4 bidirectional TT_ha I/O; AF: SPI1_NSS (boot), SPI3_NSS, USART2_CK, DCMI_HSYNC; additional: ADC1_IN9, ADC2_IN9, ADC4_IN9, DAC1_OUT1, WKUP2.
21 PA5 bidirectional TT_a I/O; AF: TIM2_CH1, TIM8_CH1N, SPI1_SCK (boot), USART3_RX; additional: ADC1_IN10, ADC2_IN10, ADC4_IN10, DAC1_OUT2, WKUP6.
22 PA6 bidirectional FT_ha I/O; AF: TIM1_BKIN, TIM3_CH1, SPI1_MISO (boot), USART3_CTS, LPUART1_CTS; additional: OPAMP2_VINP, ADC1_IN11, ADC2_IN11, ADC4_IN11, WKUP7.
23 PA7 bidirectional FT_fha I/O; AF: TIM1_CH1N, TIM3_CH2, I2C3_SCL, SPI1_MOSI (boot), USART3_TX; additional: OPAMP2_VINM, ADC1_IN12, ADC2_IN12, ADC4_IN20, WKUP8.
24 PB0 bidirectional TT_ha I/O; AF: TIM1_CH2N, TIM3_CH3, LPTIM3_CH1, SPI1_NSS, USART3_CK, COMP1_OUT; additional: OPAMP2_VOUT, ADC1_IN15, ADC2_IN15, ADC4_IN18.
25 PB1 bidirectional FT_ha I/O; AF: TIM1_CH3N, TIM3_CH4, LPTIM3_CH2, MDF1_SDI0, USART3_RTS_DE; additional: COMP1_INM1, ADC1_IN16, ADC2_IN16, ADC4_IN19, WKUP4.
26 PB2 bidirectional FT_hat I/O; AF: LPTIM1_CH1, I2C3_SMBA, SPI1_RDY, MDF1_CKI0; additional: COMP1_INP2, ADC1_IN17, ADC2_IN17, WKUP1, RTC_OUT2.
27 PB10 bidirectional FT_fhv I/O; AF: TIM2_CH3, LPTIM3_CH1, I2C4_SCL, I2C2_SCL (boot), SPI2_SCK, USART3_TX, LPUART1_RX, COMP1_OUT; additional: WKUP8.
28 VLXSMPS passive SMPS step-down converter switching output, connected through an external 2.2 µH inductor (ISAT > 0.5 A, DCR < 200 mΩ) to the VDD11 pins.
29 VDDSMPS power_in SMPS step-down converter supply input, requiring a 10 µF ±20% (ESR < 10 mΩ at 3 MHz, rated ≥ 10 V) capacitor.
30 VSSSMPS power_in SMPS step-down converter ground.
31 VDD11 power_in 1.1 V VCORE supply fed by the filtered SMPS output (or LDO), needing 2 × 2.2 µF ±20% (ESR < 20 mΩ at 3 MHz, rated ≥ 10 V) across the VDD11 pins.
32 VSS power_in Digital ground.
33 VDD power_in Digital supply voltage.
34 PB13 bidirectional FT_fa I/O; AF: TIM1_CH1N, LPTIM3_IN1, I2C2_SCL, SPI2_SCK (boot), USART3_CTS, LPUART1_CTS, SAI2_SCK_A.
35 PB14 bidirectional FT_fda I/O; AF: TIM1_CH2N, I2C2_SDA, SPI2_MISO (boot), USART3_RTS_DE, SDMMC2_D0; additional: UCPD1_DBCC2 (dead battery control).
36 PB15 bidirectional FT_c I/O; AF: RTC_REFIN, TIM1_CH3N, SPI2_MOSI (boot), SDMMC2_D1; additional: UCPD1_CC2, WKUP7; UCPD pull-down Rd 5.1 kΩ may be active after reset.
37 PC6 bidirectional FT_a I/O; AF: TIM3_CH1, TIM8_CH1, MDF1_CKI3, LCD_R0, SDMMC1_D0DIR, DCMI_D0, SAI2_MCLK_A.
38 PC7 bidirectional FT_a I/O; AF: TIM3_CH2, TIM8_CH2, MDF1_SDI3, LCD_R1, SDMMC1_D123DIR, DCMI_D1, SAI2_MCLK_B.
39 PC8 bidirectional FT_a I/O; AF: TIM3_CH3, TIM8_CH3, USART6_RX, SDMMC1_D0, LPTIM3_CH1.
40 PC9 bidirectional FT_a I/O; AF: TIM3_CH4, TIM8_CH4, USART6_TX, SDMMC1_D1, LPTIM3_CH2, TRACED0.
41 PA8 bidirectional FT_hv I/O; AF: MCO, TIM1_CH1, SPI1_RDY, USART1_CK, OTG_HS_SOF, SAI1_SCK_A.
42 PA9 bidirectional FT_u I/O; AF: TIM1_CH2, SPI2_SCK, USART1_TX (boot), SAI1_FS_A; additional: OTG_HS_VBUS.
43 PA10 bidirectional FT_u I/O; AF: CRS_SYNC, TIM1_CH3, USART1_RX (boot), OTG_HS_ID, SAI1_SD_A.
44 PA11 bidirectional TT I/O, 5V-tolerant when USB PHY is powered; AF: TIM1_CH4, SPI1_MISO, USART1_CTS, FDCAN1_RX; additional: OTG_HS_DM (boot).
45 PA12 bidirectional TT I/O, 5V-tolerant when USB PHY is powered; AF: TIM1_ETR, SPI1_MOSI, USART1_RTS_DE, FDCAN1_TX; additional: OTG_HS_DP (boot).
46 PA13 bidirectional FT I/O configured as JTMS/SWDIO after reset with internal pull-up active; AF: IR_OUT, SAI1_SD_B.
47 VSS power_in Digital ground.
48 VDDUSB power_in Independent USB transceiver supply.
49 PA14 bidirectional FT I/O configured as JTCK/SWCLK after reset with internal pull-down active; AF: LPTIM1_CH1, I2C1_SMBA, OTG_HS_SOF.
50 PA15 (JTDI) bidirectional FT_c I/O configured as JTDI after reset with internal pull-up active; AF: TIM2_CH1, SPI1_NSS, USART2_RX; additional: UCPD1_CC1 (Rd 5.1 kΩ pull-down may be active after reset).
51 PC10 bidirectional FT_a I/O; AF: SPI3_SCK, USART3_TX (boot), UART4_TX, SDMMC1_D2, SAI2_SCK_B, TRACED1.
52 PC11 bidirectional FT_ha I/O; AF: SPI3_MISO, USART3_RX (boot), UART4_RX, SDMMC1_D3, SAI2_MCLK_B.
53 PC12 bidirectional FT_hav I/O; AF: SPI3_MOSI, USART3_CK, UART5_TX, SDMMC1_CK, SAI2_SD_B, TRACED3.
54 PD2 bidirectional FT I/O; AF: TIM3_ETR, USART3_RTS_DE, UART5_RX, SDMMC1_CMD, TRACED2.
55 PB3 bidirectional FT_fa I/O configured as JTDO/TRACESWO after reset; AF: TIM2_CH2, I2C1_SDA, SPI1_SCK, SPI3_SCK; additional: COMP2_INM2.
56 PB4 (NJTRST) bidirectional FT_fa I/O configured as NJTRST after reset with internal pull-up active; AF: TIM3_CH1, I2C3_SDA, SPI1_MISO, SPI3_MISO; additional: COMP2_INP1.
57 PB5 bidirectional FT_havc I/O; AF: TIM3_CH2, I2C1_SMBA, SPI1_MOSI, SPI3_MOSI (boot), UART5_CTS; additional: UCPD1_DBCC1, WKUP6.
58 PB6 bidirectional FT_fa I/O; AF: TIM4_CH1, I2C1_SCL (boot), I2C4_SCL, USART1_TX; additional: COMP2_INP2, WKUP3.
59 PB7 bidirectional FT_fhav I/O; AF: TIM4_CH2, I2C1_SDA (boot), I2C4_SDA, USART1_RX, UART4_CTS; additional: COMP2_INM1, PVD_IN, WKUP4.
60 PH3-BOOT0 input FT I/O (PH3) that serves as BOOT0 boot mode selection input; AF: EVENTOUT.
61 PB8 bidirectional FT_f I/O; AF: TIM4_CH3, I2C1_SCL, SDMMC1_CKIN, FDCAN1_RX (boot), SAI1_MCLK_A; additional: WKUP5.
62 VDD11 power_in 1.1 V VCORE supply fed by the filtered SMPS output (or LDO), needing 2 × 2.2 µF ±20% (ESR < 20 mΩ at 3 MHz, rated ≥ 10 V) across the VDD11 pins.
63 VSS power_in Digital ground.
64 VDD power_in Digital supply voltage.

Key specifications

Parameter Value
Manufacturer STMicroelectronics
Package LQFP-64(10x10)
Category
Pins 64

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
External main supply voltage (VDDSMPS, VDDA, VDDUSB, VDDDSI, VBAT, VREF+) VDDX - VSS -0.3 4 V 181
I/O supply when HSLV = 0 VDDIOx - VSS -0.3 4 V HSLV = 0 181
I/O supply when HSLV = 1 VDDIOx - VSS -0.3 2.75 V HSLV = 1 181
Input voltage on FT_c pins VIN 5.5 V FT_c pins 181
Input voltage on any other pins VIN 4 V any other pins 181
Allowed voltage difference for VREF+ > VDDA VREF+ - VDDA 0.4 V VREF+ > VDDA 181
Variations between different VDDx power pins of the same domain /ΔVDDx/ 50 mV 181
Variations between all the different ground pins /VSSx-VSS/ 50 mV including VREF- pin 181
Storage temperature range TSTG -65 150 °C 182
Maximum junction temperature TJ 140 °C 182
Total current into sum of all VDD power lines (source) ∑IVDD 200 mA 182
Total current out of sum of all VSS ground lines (sink) ∑IVSS 200 mA 182
Maximum current into each VDD power pin (source) IVDD 100 mA 182
Maximum current out of each VSS ground pin (sink) IVSS 100 mA 182
Output current sunk by any I/O and control pin IIO 20 mA sunk 182
Output current sourced by any I/O and control pin IIO 20 mA sourced 182
Total output current sunk by sum of all I/Os and control pins ∑I(PIN) 120 mA sunk 182
Total output current sourced by sum of all I/Os and control pins ∑I(PIN) 120 mA sourced 182
Injected current on FT_xx, TT_xx, RST pins IINJ(PIN) -5 0 mA FT_xx, TT_xx, RST pins 182
Total injected current (sum of all I/Os and control pins) ∑/IINJ(PIN)/ 25 mA 182
Standard operating voltage VDD 1.71 3.6 V IO_VDD_HSLV = 0 183
Standard operating voltage VDD 1.71 2.7 V IO_VDD_HSLV = 1 183
Supply voltage for PG[15:2] I/Os VDDIO2 1.08 3.6 V At least one I/O in PG[15:2] used, IO_VDDIO2_HSLV = 0 183
Supply voltage for PG[15:2] I/Os VDDIO2 1.08 2.7 V At least one I/O in PG[15:2] used, IO_VDDIO2_HSLV = 1 183
Supply voltage for PG[15:2] I/Os VDDIO2 0 3.6 V PG[15:2] I/Os not used 183
USB supply voltage VDDUSB 3 3.6 V USB used 183
USB supply voltage VDDUSB 0 3.6 V USB not used 183
Analog supply voltage VDDA 1.58 3.6 V COMP used 183
Analog supply voltage VDDA 1.6 3.6 V DAC or OPAMP used 183
Analog supply voltage VDDA 1.62 3.6 V ADC used 183
Analog supply voltage VDDA 1.8 3.6 V VREFBUF used (normal mode) 183
Analog supply voltage VDDA 0 3.6 V ADC, DAC, COMP, OPAMP, and VREFBUF not used 183
Backup domain supply voltage VBAT 1.65 3.6 V 183
I/O input voltage VIN -0.3 5 V FT_c I/Os 183
I/O input voltage VIN -0.3 V TT_xx I/Os 183
Sum of output current sourced by all I/Os powered by VSW IIO_SW 3 mA 183
Internal regulator ON, Range 1 VCORE VCORE 1.15 1.21 1.27 V Range 1 184
Internal regulator ON, Range 2 VCORE VCORE 1.05 1.1 1.15 V Range 2 184
Internal regulator ON, Range 3 VCORE VCORE 0.95 1 1.05 V Range 3 184
Internal regulator ON, Range 4 VCORE VCORE 0.81 0.9 0.99 V Range 4 184
AHB clock frequency fHCLK 160 MHz Range 1 184
AHB clock frequency fHCLK 110 MHz Range 2 184
AHB clock frequency fHCLK 55 MHz Range 3 184
AHB clock frequency fHCLK 25 MHz Range 4 184
APB1, APB2, APB3 clock frequency fPCLKx (x = 1, 2, 3) 160 MHz Range 1 184
APB1, APB2, APB3 clock frequency fPCLKx (x = 1, 2, 3) 110 MHz Range 2 184
APB1, APB2, APB3 clock frequency fPCLKx (x = 1, 2, 3) 55 MHz Range 3 184
APB1, APB2, APB3 clock frequency fPCLKx (x = 1, 2, 3) 25 MHz Range 4 184
Ambient temperature for suffix 6, maximum power dissipation TA -40 85 °C Maximum power dissipation 184
Ambient temperature for suffix 6, low-power dissipation TA -40 105 °C Low-power dissipation 184
Junction temperature range, suffix 6 version TJ -40 105 °C Suffix 6 version 185
VDD fall-time rate tVDD 20 µs/V ULPMEN = 0 (default value) 185
Internal reference voltage VREFINT 1.175 1.215 1.255 V Range 1, 2, 3 188
Average temperature coefficient TCoeff 40 125 ppm/°C -40°C < TJ < +130 °C 188
Average voltage coefficient VDDCoeff 500 2900 ppm/V 3.0 V ≤ VDD ≤ 3.6 V 188
Brownout reset threshold 0 rising edge VBOR0 1.6 1.66 1.71 V Rising edge 186
Brownout reset threshold 0 falling edge VBOR0 1.58 1.64 1.69 V Falling edge, range 1, 2, 3 186

CAD (KiCad official)

  • Symbol: STM32U595RJT6Q
  • Footprint: Package_QFP:LQFP-64_10x10mm_P0.5mm
  • 3D model: LQFP-64(10x10) (KiCad packages3D, STEP)
  • 3D model files: stm32u595rjt6q-etched.step / stm32u595rjt6q-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); stm32u595rjt6q.step / stm32u595rjt6q.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: STMicroelectronics datasheet (385 pp, sha256 1a6951f7fcbc7a72, retrieved 2026-11-09, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF