component
STM32U385CGT6Q
Public Made by Adomby adom
STMicroelectronics , LQFP-48(7x7). Pinout checked against ST's open pin data, KiCad symbol/footprint/3D.
main
Ray
Publish 0.1.0
7a084c3
STM32U385CGT6Q
STMicroelectronics · IC · LQFP-48(7x7)
STM32U385CGT6Q from STMicroelectronics, in a LQFP-48(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model, then checked against ST open pin data). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VBAT | power_in | Backup-domain supply input, 1.55 V to 3.6 V, powering the RTC, TAMP, external 32 kHz oscillator and backup registers when VDD is not present. |
| 2 | PC13 | bidirectional | FT I/O supplied through the power switch (VSW), which sinks only 3 mA, so output use is limited to 2 MHz with a maximum 30 pF load and it must not drive current sources such as LEDs; also RTC/tamper functions (WKUP2, RTC_TS/RTC_OUT1, TAMP_IN1). |
| 3 | PC14-OSC32_IN | bidirectional | FT_o I/O supplied through the VSW power switch, with OSC32_IN function for the 32.768 kHz LSE oscillator; FT_o electrical characteristics apply. |
| 4 | PC15-OSC32_OUT | bidirectional | FT_o I/O supplied through the VSW power switch, with OSC32_OUT function for the 32.768 kHz LSE oscillator; FT_o electrical characteristics apply. |
| 5 | PH0-OSC_IN | bidirectional | 5 V-tolerant (FT) I/O that also serves as the OSC_IN high-speed external oscillator input. |
| 6 | PH1-OSC_OUT | bidirectional | 5 V-tolerant (FT) I/O that also serves as the OSC_OUT high-speed external oscillator output. |
| 7 | NRST | bidirectional | Bidirectional reset pin with an embedded weak pull-up resistor (RST structure). |
| 8 | VSSA | power_in | Analog ground for ADC, DAC, OPAMP, comparators and VREFBUF; ground-pin variation between VSSx and VSS must not exceed 50 mV. |
| 9 | VDDA | power_in | Analog supply: 1.58 V (COMP), 1.60 V (DAC/OPAMP), 1.62 V (ADC) or 1.80 V (VREFBUF) to 3.6 V; must be connected to VDD when these peripherals are not used. |
| 10 | PA0 | bidirectional | 5 V-tolerant I/O (FT_a) with analog switch function supplied by VDDA; additional functions include OPAMP1_VINP, ADC1_IN3 and WKUP1. |
| 11 | PA1 | bidirectional | 5 V-tolerant I/O (FT_fha) with Fm+ capability, high-speed low-voltage mode and analog switch supplied by VDDA; additional functions include OPAMP1_VINM, ADC1_IN4 and WKUP3. |
| 12 | PA2 | bidirectional | 5 V-tolerant I/O (FT_ha) with high-speed low-voltage mode and analog switch supplied by VDDA; additional functions include COMP1_INP3, ADC1_IN5 and WKUP4/LSCO. |
| 13 | PA3 | bidirectional | 3.6 V-tolerant I/O (TT_ha) with high-speed low-voltage mode and analog switch supplied by VDDA; additional functions include OPAMP1_VOUT, COMP1_INP4, ADC1_IN6 and WKUP5. |
| 14 | PA4 | bidirectional | 3.6 V-tolerant I/O (TT_ha) with high-speed low-voltage mode and analog switch supplied by VDDA; additional functions include ADC1_IN7, ADC2_IN3, DAC1_OUT1 and WKUP2. |
| 15 | PA5 | bidirectional | 3.6 V-tolerant I/O (TT_a) with analog switch function supplied by VDDA; additional functions include ADC1_IN8, ADC2_IN4, DAC1_OUT2 and WKUP6. |
| 16 | PA6 | bidirectional | 5 V-tolerant I/O (FT_fha) with Fm+ capability, high-speed low-voltage mode and analog switch supplied by VDDA; additional functions include OPAMP2_VINP, ADC1_IN9, ADC2_IN5 and WKUP7. |
| 17 | PA7 | bidirectional | 5 V-tolerant I/O (FT_fha) with Fm+ capability, high-speed low-voltage mode and analog switch supplied by VDDA; additional functions include OPAMP2_VINM, ADC1_IN10, ADC2_IN6 and WKUP8. |
| 18 | PB0 | bidirectional | 3.6 V-tolerant I/O (TT_ha) with high-speed low-voltage mode and analog switch supplied by VDDA; additional functions include OPAMP2_VOUT, ADC1_IN13 and ADC2_IN9. |
| 19 | PB1 | bidirectional | 5 V-tolerant I/O (FT_ha) with high-speed low-voltage mode and analog switch supplied by VDDA; additional functions include COMP1_INM1, ADC1_IN14, ADC2_IN10 and WKUP4. |
| 20 | VLXSMPS | power_out | Switched output of the SMPS step-down converter, connected through an external inductor (2.2 µH ±20%, ISAT > 0.5 A, DCR < 200 mΩ) to VDD11. |
| 21 | VDDSMPS | power_in | Supply input for the SMPS step-down converter, 1.71 V to 3.6 V; must be connected to VDD when the SMPS is used, and connected to GND together with VLXSMPS when it is not used. |
| 22 | VSSSMPS | power_in | SMPS ground pin; ground-pin variation between all VSSx pins and VSS must not exceed 50 mV. |
| 23 | VDD11 | power_out | SMPS output node requiring external capacitors of 2 × 2.2 µF ±20% (ESR < 20 mΩ at 3 MHz, rated voltage ≥ 10 V). |
| 24 | VSS | power_in | Ground pin; all voltages are referenced to VSS and ground pins must be connected to the external supply within the permitted range. |
| 25 | VDD | power_in | Main supply pin, 1.71 V to 3.6 V (functionality guaranteed down to VBOR min); supplies the I/Os, internal regulator and system analog. |
| 26 | PB13 | bidirectional | 5 V-tolerant I/O (FT_fha) with Fm+ capability and high-speed low-voltage mode; alternate functions include TIM1_CH1N, LPUART1_CTS and TIM15_CH1N. |
| 27 | PB14 | bidirectional | 5 V-tolerant I/O (FT_fha) with Fm+ capability and high-speed low-voltage mode; alternate functions include TIM1_CH2N, SPI2_MISO and TIM15_CH1. |
| 28 | PB15 | bidirectional | 5 V-tolerant I/O (FT_a) with analog switch function supplied by VDDA; additional functions include RTC_REFIN and WKUP7. |
| 29 | PA8 | bidirectional | 5 V-tolerant I/O (FT_h) with high-speed low-voltage mode; alternate functions include MCO, TIM1_CH1 and USART1_CK. |
| 30 | PA9 | bidirectional | 5 V-tolerant I/O (FT); alternate functions include MCO, TIM1_CH2 and USART1_TX (boot). |
| 31 | PA10 | bidirectional | 5 V-tolerant I/O (FT); alternate functions include CRS_SYNC, TIM1_CH3 and USART1_RX (boot). |
| 32 | PA11 | bidirectional | 5 V-tolerant I/O (FT_u) with USB function supplied by VDDUSB; additional function USB_DM (boot), alternate functions include TIM1_CH4 and USART1_CTS. |
| 33 | PA12 | bidirectional | 5 V-tolerant I/O (FT_u) with USB function supplied by VDDUSB; additional function USB_DP (boot), alternate functions include TIM1_ETR and USART1_RTS. |
| 34 | PA13 (JTMS/SWDIO) | bidirectional | 5 V-tolerant I/O that after reset is configured as JTMS/SWDIO with its internal pull-up activated. |
| 35 | VSS | power_in | Ground pin; all voltages are referenced to VSS. |
| 36 | VDD | power_in | Main supply pin, 1.71 V to 3.6 V, supplying the I/Os, internal regulator and system analog. |
| 37 | PA14 (JTCK/SWCLK) | bidirectional | 5 V-tolerant I/O that after reset is configured as JTCK/SWCLK with its internal pull-down activated. |
| 38 | PA15 (JTDI) | bidirectional | 5 V-tolerant I/O (FT_a) with analog switch function supplied by VDDA that after reset is configured as JTDI with its internal pull-up activated. |
| 39 | PB3 (JTDO/TRACESWO) | bidirectional | 5 V-tolerant I/O (FT_fha) with Fm+ capability and analog switch supplied by VDDA; additional function COMP2_INM2. |
| 40 | PB4 (NJTRST) | bidirectional | 5 V-tolerant I/O (FT_fha) with analog switch supplied by VDDA that after reset is configured as NJTRST with its internal pull-up activated. |
| 41 | PB5 | bidirectional | 5 V-tolerant I/O (FT_ha) with high-speed low-voltage mode and analog switch supplied by VDDA; additional function WKUP6. |
| 42 | PB6 | bidirectional | 5 V-tolerant I/O (FT_fha) with Fm+ capability and high-speed low-voltage mode; additional functions include COMP2_INP2 and WKUP3. |
| 43 | PB7 | bidirectional | 5 V-tolerant I/O (FT_fha) with Fm+ capability and high-speed low-voltage mode; additional functions include COMP2_INM1, PVD_IN and WKUP4. |
| 44 | PH3-BOOT0 | bidirectional | 5 V-tolerant I/O (FT_fh) that serves as the BOOT0 boot-selection pin on this package (boot function is available on all packages except WLCSP68 SMPS-G). |
| 45 | PB8 | bidirectional | 5 V-tolerant I/O (FT_fh) with Fm+ capability and high-speed low-voltage mode; additional function WKUP5, alternate functions include TIM4_CH3 and I2C1_SCL. |
| 46 | VDD11 | power_out | SMPS output node requiring external capacitors of 2 × 2.2 µF ±20% (ESR < 20 mΩ at 3 MHz, rated voltage ≥ 10 V). |
| 47 | VSS | power_in | Ground pin; all voltages are referenced to VSS. |
| 48 | VDD | power_in | Main supply pin, 1.71 V to 3.6 V, supplying the I/Os, internal regulator and system analog. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | LQFP-48(7x7) |
| Category | |
| Pins | 48 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| External main supply voltage (VDD, VDDSMPS, VDDA, VDDUSB, VDDIO2, VBAT, VREF+) | VDDX - VSS | -0.3 | 4 | V | 96 | ||
| I/O supply when HSLV = 0 | VDDIOx - VSS | -0.3 | 4 | V | HSLV = 0 | 97 | |
| I/O supply when HSLV = 1 | VDDIOx - VSS | -0.3 | 2.75 | V | HSLV = 1 | 97 | |
| Input voltage on PC13 and FT_o pins in VBAT mode | VIN | -0.3 | 4 | V | Min printed as VSS - 0.3 | 97 | |
| Input voltage on any other pins | VIN | -0.3 | 4 | V | Min printed as VSS - 0.3 | 97 | |
| Input voltage on FT_xx pins | VIN | -0.3 | V | Min printed as VSS - 0.3; max printed as Min(min(VDD, VDDA, VDDUSB, VDDIO2) + 4.0, 6.0), not computed | 97 | ||
| Allowed voltage difference for VREF+ > VDDA | VREF+ - VDDA | 0.4 | V | VREF+ > VDDA | 97 | ||
| Variations between different VDDx power pins of the same domain | ΔVDDx | 50 | mV | 97 | |||
| Variations between all the different ground pins (including VREF-) | VSSx - VSS | 50 | mV | 97 | |||
| Total current into sum of all VDD power lines (source) | ∑IVDD | 150 | mA | 97 | |||
| Total current out of sum of all VSS ground lines (sink) | ∑IVSS | 150 | mA | 97 | |||
| Maximum current into each VDD power pin (source) | IVDD | 100 | mA | 97 | |||
| Maximum current out of each VSS ground pin (sink) | IVSS | 100 | mA | 97 | |||
| Output current sunk by any I/O and control pin | IIO | 20 | mA | 97 | |||
| Output current sourced by any I/O and control pin | IIO | 20 | mA | 97 | |||
| Total output current sunk by sum of all I/Os and control pins | ∑I(PIN) | 120 | mA | 97 | |||
| Total output current sourced by sum of all I/Os and control pins | ∑I(PIN) | 120 | mA | 97 | |||
| Injected current on FT_xx, TT_xx, RST pins | IINJ(PIN) | -5 | 0 | mA | Printed as -5/+0 | 97 | |
| Total injected current (sum of all I/Os and control pins) | ∑IINJ(PIN) | -25 | 25 | mA | Printed as ±25 | 97 | |
| Storage temperature range | TSTG | -65 | 150 | °C | 97 | ||
| Maximum junction temperature | TJ | 110 | °C | 97 | |||
| Standard operating voltage | VDD | 1.71 | 3.6 | V | HSLV = 0 | 98 | |
| Standard operating voltage | VDD | 1.71 | 2.7 | V | HSLV = 1 | 98 | |
| Supply voltage for PG[15:2] I/Os | VDDIO2 | 1.08 | 3.6 | V | At least one I/O in PG[15:2] used, HSLV = 0 | 98 | |
| Supply voltage for PG[15:2] I/Os | VDDIO2 | 2.7 | V | At least one I/O in PG[15:2] used, HSLV = 1; single printed value assigned to min | 98 | ||
| Supply voltage for PG[15:2] I/Os | VDDIO2 | 0 | 3.6 | V | PG[15:2] not used | 98 | |
| USB supply voltage | VDDUSB | 3 | 3.6 | V | USB used | 98 | |
| USB supply voltage | VDDUSB | 0 | V | USB not used; single printed value assigned to min | 98 | ||
| Analog supply voltage | VDDA | 1.58 | 3.6 | V | COMP used | 98 | |
| Analog supply voltage | VDDA | 1.6 | 3.6 | V | DAC or OPAMP used | 98 | |
| Analog supply voltage | VDDA | 1.62 | 3.6 | V | ADC used | 98 | |
| Analog supply voltage | VDDA | 1.8 | 3.6 | V | VREFBUF used (normal mode) | 98 | |
| Backup domain supply voltage | VBAT | 1.55 | 3.6 | V | 98 | ||
| I/O input voltage | VIN | -0.3 | V | All I/Os except TT_xx pins; max printed as Min(min(VDD, VDDA, VDDUSB, VDDIO2) + 3.6, 5.5), not computed | 98 | ||
| I/O input voltage | VIN | -0.3 | 3.6 | V | Input voltage on PC13 and FT_o pins in VBAT mode | 98 | |
| Sum of output current sourced by all I/Os powered by VSW | IIO_SW | 3 | mA | I/Os powered by VSW: PC13, PC14, PC15 | 98 | ||
| Internal regulator core voltage | VCORE | 0.8 | 0.9 | 1 | V | Internal regulator ON, Range 1 | 98 |
| Internal regulator core voltage | VCORE | 0.65 | 0.75 | 0.85 | V | Internal regulator ON, Range 2 | 98 |
| AHB clock frequency | fHCLK | 96 | MHz | Range 1 | 98 | ||
| AHB clock frequency | fHCLK | 48 | MHz | Range 2 | 98 | ||
| APB1, APB2, APB3 clock frequency | fPCLKx | 96 | MHz | Range 1, x = 1, 2, 3 | 98 | ||
| APB1, APB2, APB3 clock frequency | fPCLKx | 48 | MHz | Range 2, x = 1, 2, 3 | 98 | ||
| Ambient temperature for suffix 6 | TA | -40 | 85 | °C | Maximum power dissipation | 99 | |
| Ambient temperature for suffix 6 | TA | 105 | °C | Low-power dissipation | 99 | ||
| Junction temperature range, suffix 6 version | TJ | -40 | 105 | °C | Suffix 6 version | 99 | |
| VDD rise-time rate | tVDD | 0 | µs/V | Max printed as ∞ | 100 | ||
| VDD fall-time rate | tVDD | 20 | µs/V | ULPMEN = 0; max printed as ∞ | 100 | ||
| VDD fall-time rate | tVDD | 250 | ms/V | Standby mode, BOR level 0 selected with ULPMEN = 1; max printed as ∞ | 100 | ||
| Reset temporization after BOR0 released | tRSTTEMPO | 900 | µs | VDD rising | 100 | ||
| Brownout reset threshold 0 | VBOR0 | 1.63 | 1.65 | 1.67 | V | Rising edge | 100 |
| Brownout reset threshold 0 | VBOR0 | 1.62 | 1.63 | 1.65 | V | Falling edge, Range 1 | 100 |
| Internal reference voltage | VREFINT | 1.175 | 1.215 | 1.243 | V | Range 1 | 102 |
| Internal reference voltage | VREFINT | 1.17 | 1.215 | 1.248 | V | Range 2 and low-power modes | 102 |
| Average temperature coefficient | Tcoeff | 62 | 150 | ppm/°C | -40 °C ≤ TJ ≤ 110 °C | 102 | |
| Average voltage coefficient | VDDcoeff1 | 600 | 2300 | ppm/V | 3.0 V ≤ VDD ≤ 3.6 V for -40 °C ≤ TJ ≤ +110 °C | 102 | |
| Average voltage coefficient | VDDcoeff2 | 270 | 1150 | ppm/V | 1.8 V ≤ VDD ≤ 3.6 V for -40 °C ≤ TJ ≤ +110 °C | 102 | |
| Supply current in Run mode on LDO, Range 1 | IDD (Run) | 4.6 | 6 | mA | fHCLK = fMSI 96 MHz, all peripherals disabled, flash bank 2 powered down, all SRAMs enabled; typ at 25 °C, max at 30 °C | 103 | |
| Supply current in Standby mode, no independent watchdog | IDD (Standby) | 0.18 | 0.55 | µA | VDD = 3 V, PWR_CR1.ULPMEN = 1, RTC disabled; typ at 25 °C, max at 30 °C | 120 |
CAD (KiCad official)
- Symbol:
STM32U385CGT6Q - Footprint:
Package_QFP:LQFP-48_7x7mm_P0.5mm - 3D model: LQFP-48(7x7) (KiCad packages3D, STEP)
- 3D model files:
stm32u385cgt6q-etched.step/stm32u385cgt6q-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);stm32u385cgt6q.step/stm32u385cgt6q.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: STMicroelectronics datasheet (232 pp, sha256
e939cd842042f13b, retrieved 2026-11-13, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# STM32U385CGT6Q
**STMicroelectronics** · IC · LQFP-48(7x7)
STM32U385CGT6Q from STMicroelectronics, in a LQFP-48(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model, then checked against ST open pin data). Symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VBAT | power_in | Backup-domain supply input, 1.55 V to 3.6 V, powering the RTC, TAMP, external 32 kHz oscillator and backup registers when VDD is not present. |
| 2 | PC13 | bidirectional | FT I/O supplied through the power switch (VSW), which sinks only 3 mA, so output use is limited to 2 MHz with a maximum 30 pF load and it must not drive current sources such as LEDs; also RTC/tamper functions (WKUP2, RTC_TS/RTC_OUT1, TAMP_IN1). |
| 3 | PC14-OSC32_IN | bidirectional | FT_o I/O supplied through the VSW power switch, with OSC32_IN function for the 32.768 kHz LSE oscillator; FT_o electrical characteristics apply. |
| 4 | PC15-OSC32_OUT | bidirectional | FT_o I/O supplied through the VSW power switch, with OSC32_OUT function for the 32.768 kHz LSE oscillator; FT_o electrical characteristics apply. |
| 5 | PH0-OSC_IN | bidirectional | 5 V-tolerant (FT) I/O that also serves as the OSC_IN high-speed external oscillator input. |
| 6 | PH1-OSC_OUT | bidirectional | 5 V-tolerant (FT) I/O that also serves as the OSC_OUT high-speed external oscillator output. |
| 7 | NRST | bidirectional | Bidirectional reset pin with an embedded weak pull-up resistor (RST structure). |
| 8 | VSSA | power_in | Analog ground for ADC, DAC, OPAMP, comparators and VREFBUF; ground-pin variation between VSSx and VSS must not exceed 50 mV. |
| 9 | VDDA | power_in | Analog supply: 1.58 V (COMP), 1.60 V (DAC/OPAMP), 1.62 V (ADC) or 1.80 V (VREFBUF) to 3.6 V; must be connected to VDD when these peripherals are not used. |
| 10 | PA0 | bidirectional | 5 V-tolerant I/O (FT_a) with analog switch function supplied by VDDA; additional functions include OPAMP1_VINP, ADC1_IN3 and WKUP1. |
| 11 | PA1 | bidirectional | 5 V-tolerant I/O (FT_fha) with Fm+ capability, high-speed low-voltage mode and analog switch supplied by VDDA; additional functions include OPAMP1_VINM, ADC1_IN4 and WKUP3. |
| 12 | PA2 | bidirectional | 5 V-tolerant I/O (FT_ha) with high-speed low-voltage mode and analog switch supplied by VDDA; additional functions include COMP1_INP3, ADC1_IN5 and WKUP4/LSCO. |
| 13 | PA3 | bidirectional | 3.6 V-tolerant I/O (TT_ha) with high-speed low-voltage mode and analog switch supplied by VDDA; additional functions include OPAMP1_VOUT, COMP1_INP4, ADC1_IN6 and WKUP5. |
| 14 | PA4 | bidirectional | 3.6 V-tolerant I/O (TT_ha) with high-speed low-voltage mode and analog switch supplied by VDDA; additional functions include ADC1_IN7, ADC2_IN3, DAC1_OUT1 and WKUP2. |
| 15 | PA5 | bidirectional | 3.6 V-tolerant I/O (TT_a) with analog switch function supplied by VDDA; additional functions include ADC1_IN8, ADC2_IN4, DAC1_OUT2 and WKUP6. |
| 16 | PA6 | bidirectional | 5 V-tolerant I/O (FT_fha) with Fm+ capability, high-speed low-voltage mode and analog switch supplied by VDDA; additional functions include OPAMP2_VINP, ADC1_IN9, ADC2_IN5 and WKUP7. |
| 17 | PA7 | bidirectional | 5 V-tolerant I/O (FT_fha) with Fm+ capability, high-speed low-voltage mode and analog switch supplied by VDDA; additional functions include OPAMP2_VINM, ADC1_IN10, ADC2_IN6 and WKUP8. |
| 18 | PB0 | bidirectional | 3.6 V-tolerant I/O (TT_ha) with high-speed low-voltage mode and analog switch supplied by VDDA; additional functions include OPAMP2_VOUT, ADC1_IN13 and ADC2_IN9. |
| 19 | PB1 | bidirectional | 5 V-tolerant I/O (FT_ha) with high-speed low-voltage mode and analog switch supplied by VDDA; additional functions include COMP1_INM1, ADC1_IN14, ADC2_IN10 and WKUP4. |
| 20 | VLXSMPS | power_out | Switched output of the SMPS step-down converter, connected through an external inductor (2.2 µH ±20%, ISAT > 0.5 A, DCR < 200 mΩ) to VDD11. |
| 21 | VDDSMPS | power_in | Supply input for the SMPS step-down converter, 1.71 V to 3.6 V; must be connected to VDD when the SMPS is used, and connected to GND together with VLXSMPS when it is not used. |
| 22 | VSSSMPS | power_in | SMPS ground pin; ground-pin variation between all VSSx pins and VSS must not exceed 50 mV. |
| 23 | VDD11 | power_out | SMPS output node requiring external capacitors of 2 × 2.2 µF ±20% (ESR < 20 mΩ at 3 MHz, rated voltage ≥ 10 V). |
| 24 | VSS | power_in | Ground pin; all voltages are referenced to VSS and ground pins must be connected to the external supply within the permitted range. |
| 25 | VDD | power_in | Main supply pin, 1.71 V to 3.6 V (functionality guaranteed down to VBOR min); supplies the I/Os, internal regulator and system analog. |
| 26 | PB13 | bidirectional | 5 V-tolerant I/O (FT_fha) with Fm+ capability and high-speed low-voltage mode; alternate functions include TIM1_CH1N, LPUART1_CTS and TIM15_CH1N. |
| 27 | PB14 | bidirectional | 5 V-tolerant I/O (FT_fha) with Fm+ capability and high-speed low-voltage mode; alternate functions include TIM1_CH2N, SPI2_MISO and TIM15_CH1. |
| 28 | PB15 | bidirectional | 5 V-tolerant I/O (FT_a) with analog switch function supplied by VDDA; additional functions include RTC_REFIN and WKUP7. |
| 29 | PA8 | bidirectional | 5 V-tolerant I/O (FT_h) with high-speed low-voltage mode; alternate functions include MCO, TIM1_CH1 and USART1_CK. |
| 30 | PA9 | bidirectional | 5 V-tolerant I/O (FT); alternate functions include MCO, TIM1_CH2 and USART1_TX (boot). |
| 31 | PA10 | bidirectional | 5 V-tolerant I/O (FT); alternate functions include CRS_SYNC, TIM1_CH3 and USART1_RX (boot). |
| 32 | PA11 | bidirectional | 5 V-tolerant I/O (FT_u) with USB function supplied by VDDUSB; additional function USB_DM (boot), alternate functions include TIM1_CH4 and USART1_CTS. |
| 33 | PA12 | bidirectional | 5 V-tolerant I/O (FT_u) with USB function supplied by VDDUSB; additional function USB_DP (boot), alternate functions include TIM1_ETR and USART1_RTS. |
| 34 | PA13 (JTMS/SWDIO) | bidirectional | 5 V-tolerant I/O that after reset is configured as JTMS/SWDIO with its internal pull-up activated. |
| 35 | VSS | power_in | Ground pin; all voltages are referenced to VSS. |
| 36 | VDD | power_in | Main supply pin, 1.71 V to 3.6 V, supplying the I/Os, internal regulator and system analog. |
| 37 | PA14 (JTCK/SWCLK) | bidirectional | 5 V-tolerant I/O that after reset is configured as JTCK/SWCLK with its internal pull-down activated. |
| 38 | PA15 (JTDI) | bidirectional | 5 V-tolerant I/O (FT_a) with analog switch function supplied by VDDA that after reset is configured as JTDI with its internal pull-up activated. |
| 39 | PB3 (JTDO/TRACESWO) | bidirectional | 5 V-tolerant I/O (FT_fha) with Fm+ capability and analog switch supplied by VDDA; additional function COMP2_INM2. |
| 40 | PB4 (NJTRST) | bidirectional | 5 V-tolerant I/O (FT_fha) with analog switch supplied by VDDA that after reset is configured as NJTRST with its internal pull-up activated. |
| 41 | PB5 | bidirectional | 5 V-tolerant I/O (FT_ha) with high-speed low-voltage mode and analog switch supplied by VDDA; additional function WKUP6. |
| 42 | PB6 | bidirectional | 5 V-tolerant I/O (FT_fha) with Fm+ capability and high-speed low-voltage mode; additional functions include COMP2_INP2 and WKUP3. |
| 43 | PB7 | bidirectional | 5 V-tolerant I/O (FT_fha) with Fm+ capability and high-speed low-voltage mode; additional functions include COMP2_INM1, PVD_IN and WKUP4. |
| 44 | PH3-BOOT0 | bidirectional | 5 V-tolerant I/O (FT_fh) that serves as the BOOT0 boot-selection pin on this package (boot function is available on all packages except WLCSP68 SMPS-G). |
| 45 | PB8 | bidirectional | 5 V-tolerant I/O (FT_fh) with Fm+ capability and high-speed low-voltage mode; additional function WKUP5, alternate functions include TIM4_CH3 and I2C1_SCL. |
| 46 | VDD11 | power_out | SMPS output node requiring external capacitors of 2 × 2.2 µF ±20% (ESR < 20 mΩ at 3 MHz, rated voltage ≥ 10 V). |
| 47 | VSS | power_in | Ground pin; all voltages are referenced to VSS. |
| 48 | VDD | power_in | Main supply pin, 1.71 V to 3.6 V, supplying the I/Os, internal regulator and system analog. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | LQFP-48(7x7) |
| Category | |
| Pins | 48 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| External main supply voltage (VDD, VDDSMPS, VDDA, VDDUSB, VDDIO2, VBAT, VREF+) | VDDX - VSS | -0.3 | | 4 | V | | 96 |
| I/O supply when HSLV = 0 | VDDIOx - VSS | -0.3 | | 4 | V | HSLV = 0 | 97 |
| I/O supply when HSLV = 1 | VDDIOx - VSS | -0.3 | | 2.75 | V | HSLV = 1 | 97 |
| Input voltage on PC13 and FT_o pins in VBAT mode | VIN | -0.3 | | 4 | V | Min printed as VSS - 0.3 | 97 |
| Input voltage on any other pins | VIN | -0.3 | | 4 | V | Min printed as VSS - 0.3 | 97 |
| Input voltage on FT_xx pins | VIN | -0.3 | | | V | Min printed as VSS - 0.3; max printed as Min(min(VDD, VDDA, VDDUSB, VDDIO2) + 4.0, 6.0), not computed | 97 |
| Allowed voltage difference for VREF+ > VDDA | VREF+ - VDDA | | | 0.4 | V | VREF+ > VDDA | 97 |
| Variations between different VDDx power pins of the same domain | ΔVDDx | | | 50 | mV | | 97 |
| Variations between all the different ground pins (including VREF-) | VSSx - VSS | | | 50 | mV | | 97 |
| Total current into sum of all VDD power lines (source) | ∑IVDD | | | 150 | mA | | 97 |
| Total current out of sum of all VSS ground lines (sink) | ∑IVSS | | | 150 | mA | | 97 |
| Maximum current into each VDD power pin (source) | IVDD | | | 100 | mA | | 97 |
| Maximum current out of each VSS ground pin (sink) | IVSS | | | 100 | mA | | 97 |
| Output current sunk by any I/O and control pin | IIO | | | 20 | mA | | 97 |
| Output current sourced by any I/O and control pin | IIO | | | 20 | mA | | 97 |
| Total output current sunk by sum of all I/Os and control pins | ∑I(PIN) | | | 120 | mA | | 97 |
| Total output current sourced by sum of all I/Os and control pins | ∑I(PIN) | | | 120 | mA | | 97 |
| Injected current on FT_xx, TT_xx, RST pins | IINJ(PIN) | -5 | | 0 | mA | Printed as -5/+0 | 97 |
| Total injected current (sum of all I/Os and control pins) | ∑IINJ(PIN) | -25 | | 25 | mA | Printed as ±25 | 97 |
| Storage temperature range | TSTG | -65 | | 150 | °C | | 97 |
| Maximum junction temperature | TJ | | | 110 | °C | | 97 |
| Standard operating voltage | VDD | 1.71 | | 3.6 | V | HSLV = 0 | 98 |
| Standard operating voltage | VDD | 1.71 | | 2.7 | V | HSLV = 1 | 98 |
| Supply voltage for PG[15:2] I/Os | VDDIO2 | 1.08 | | 3.6 | V | At least one I/O in PG[15:2] used, HSLV = 0 | 98 |
| Supply voltage for PG[15:2] I/Os | VDDIO2 | 2.7 | | | V | At least one I/O in PG[15:2] used, HSLV = 1; single printed value assigned to min | 98 |
| Supply voltage for PG[15:2] I/Os | VDDIO2 | 0 | | 3.6 | V | PG[15:2] not used | 98 |
| USB supply voltage | VDDUSB | 3 | | 3.6 | V | USB used | 98 |
| USB supply voltage | VDDUSB | 0 | | | V | USB not used; single printed value assigned to min | 98 |
| Analog supply voltage | VDDA | 1.58 | | 3.6 | V | COMP used | 98 |
| Analog supply voltage | VDDA | 1.6 | | 3.6 | V | DAC or OPAMP used | 98 |
| Analog supply voltage | VDDA | 1.62 | | 3.6 | V | ADC used | 98 |
| Analog supply voltage | VDDA | 1.8 | | 3.6 | V | VREFBUF used (normal mode) | 98 |
| Backup domain supply voltage | VBAT | 1.55 | | 3.6 | V | | 98 |
| I/O input voltage | VIN | -0.3 | | | V | All I/Os except TT_xx pins; max printed as Min(min(VDD, VDDA, VDDUSB, VDDIO2) + 3.6, 5.5), not computed | 98 |
| I/O input voltage | VIN | -0.3 | | 3.6 | V | Input voltage on PC13 and FT_o pins in VBAT mode | 98 |
| Sum of output current sourced by all I/Os powered by VSW | IIO_SW | | | 3 | mA | I/Os powered by VSW: PC13, PC14, PC15 | 98 |
| Internal regulator core voltage | VCORE | 0.8 | 0.9 | 1 | V | Internal regulator ON, Range 1 | 98 |
| Internal regulator core voltage | VCORE | 0.65 | 0.75 | 0.85 | V | Internal regulator ON, Range 2 | 98 |
| AHB clock frequency | fHCLK | | | 96 | MHz | Range 1 | 98 |
| AHB clock frequency | fHCLK | | | 48 | MHz | Range 2 | 98 |
| APB1, APB2, APB3 clock frequency | fPCLKx | | | 96 | MHz | Range 1, x = 1, 2, 3 | 98 |
| APB1, APB2, APB3 clock frequency | fPCLKx | | | 48 | MHz | Range 2, x = 1, 2, 3 | 98 |
| Ambient temperature for suffix 6 | TA | -40 | | 85 | °C | Maximum power dissipation | 99 |
| Ambient temperature for suffix 6 | TA | | | 105 | °C | Low-power dissipation | 99 |
| Junction temperature range, suffix 6 version | TJ | -40 | | 105 | °C | Suffix 6 version | 99 |
| VDD rise-time rate | tVDD | 0 | | | µs/V | Max printed as ∞ | 100 |
| VDD fall-time rate | tVDD | 20 | | | µs/V | ULPMEN = 0; max printed as ∞ | 100 |
| VDD fall-time rate | tVDD | 250 | | | ms/V | Standby mode, BOR level 0 selected with ULPMEN = 1; max printed as ∞ | 100 |
| Reset temporization after BOR0 released | tRSTTEMPO | | | 900 | µs | VDD rising | 100 |
| Brownout reset threshold 0 | VBOR0 | 1.63 | 1.65 | 1.67 | V | Rising edge | 100 |
| Brownout reset threshold 0 | VBOR0 | 1.62 | 1.63 | 1.65 | V | Falling edge, Range 1 | 100 |
| Internal reference voltage | VREFINT | 1.175 | 1.215 | 1.243 | V | Range 1 | 102 |
| Internal reference voltage | VREFINT | 1.17 | 1.215 | 1.248 | V | Range 2 and low-power modes | 102 |
| Average temperature coefficient | Tcoeff | | 62 | 150 | ppm/°C | -40 °C ≤ TJ ≤ 110 °C | 102 |
| Average voltage coefficient | VDDcoeff1 | | 600 | 2300 | ppm/V | 3.0 V ≤ VDD ≤ 3.6 V for -40 °C ≤ TJ ≤ +110 °C | 102 |
| Average voltage coefficient | VDDcoeff2 | | 270 | 1150 | ppm/V | 1.8 V ≤ VDD ≤ 3.6 V for -40 °C ≤ TJ ≤ +110 °C | 102 |
| Supply current in Run mode on LDO, Range 1 | IDD (Run) | | 4.6 | 6 | mA | fHCLK = fMSI 96 MHz, all peripherals disabled, flash bank 2 powered down, all SRAMs enabled; typ at 25 °C, max at 30 °C | 103 |
| Supply current in Standby mode, no independent watchdog | IDD (Standby) | | 0.18 | 0.55 | µA | VDD = 3 V, PWR_CR1.ULPMEN = 1, RTC disabled; typ at 25 °C, max at 30 °C | 120 |
## CAD (KiCad official)
- Symbol: `STM32U385CGT6Q`
- Footprint: `Package_QFP:LQFP-48_7x7mm_P0.5mm`
- 3D model: LQFP-48(7x7) (KiCad packages3D, STEP)
- 3D model files: `stm32u385cgt6q-etched.step` / `stm32u385cgt6q-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `stm32u385cgt6q.step` / `stm32u385cgt6q.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [STMicroelectronics datasheet](https://www.st.com/resource/en/datasheet/stm32u385rg.pdf) (232 pp, sha256 `e939cd842042f13b`, retrieved 2026-11-13, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/stm32u385cgt6q-datasheet.pdf)