Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

STM32U385CGT6Q

STMicroelectronics · IC · LQFP-48(7x7)

STM32U385CGT6Q from STMicroelectronics, in a LQFP-48(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model, then checked against ST open pin data). Symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VBAT power_in Backup-domain supply input, 1.55 V to 3.6 V, powering the RTC, TAMP, external 32 kHz oscillator and backup registers when VDD is not present.
2 PC13 bidirectional FT I/O supplied through the power switch (VSW), which sinks only 3 mA, so output use is limited to 2 MHz with a maximum 30 pF load and it must not drive current sources such as LEDs; also RTC/tamper functions (WKUP2, RTC_TS/RTC_OUT1, TAMP_IN1).
3 PC14-OSC32_IN bidirectional FT_o I/O supplied through the VSW power switch, with OSC32_IN function for the 32.768 kHz LSE oscillator; FT_o electrical characteristics apply.
4 PC15-OSC32_OUT bidirectional FT_o I/O supplied through the VSW power switch, with OSC32_OUT function for the 32.768 kHz LSE oscillator; FT_o electrical characteristics apply.
5 PH0-OSC_IN bidirectional 5 V-tolerant (FT) I/O that also serves as the OSC_IN high-speed external oscillator input.
6 PH1-OSC_OUT bidirectional 5 V-tolerant (FT) I/O that also serves as the OSC_OUT high-speed external oscillator output.
7 NRST bidirectional Bidirectional reset pin with an embedded weak pull-up resistor (RST structure).
8 VSSA power_in Analog ground for ADC, DAC, OPAMP, comparators and VREFBUF; ground-pin variation between VSSx and VSS must not exceed 50 mV.
9 VDDA power_in Analog supply: 1.58 V (COMP), 1.60 V (DAC/OPAMP), 1.62 V (ADC) or 1.80 V (VREFBUF) to 3.6 V; must be connected to VDD when these peripherals are not used.
10 PA0 bidirectional 5 V-tolerant I/O (FT_a) with analog switch function supplied by VDDA; additional functions include OPAMP1_VINP, ADC1_IN3 and WKUP1.
11 PA1 bidirectional 5 V-tolerant I/O (FT_fha) with Fm+ capability, high-speed low-voltage mode and analog switch supplied by VDDA; additional functions include OPAMP1_VINM, ADC1_IN4 and WKUP3.
12 PA2 bidirectional 5 V-tolerant I/O (FT_ha) with high-speed low-voltage mode and analog switch supplied by VDDA; additional functions include COMP1_INP3, ADC1_IN5 and WKUP4/LSCO.
13 PA3 bidirectional 3.6 V-tolerant I/O (TT_ha) with high-speed low-voltage mode and analog switch supplied by VDDA; additional functions include OPAMP1_VOUT, COMP1_INP4, ADC1_IN6 and WKUP5.
14 PA4 bidirectional 3.6 V-tolerant I/O (TT_ha) with high-speed low-voltage mode and analog switch supplied by VDDA; additional functions include ADC1_IN7, ADC2_IN3, DAC1_OUT1 and WKUP2.
15 PA5 bidirectional 3.6 V-tolerant I/O (TT_a) with analog switch function supplied by VDDA; additional functions include ADC1_IN8, ADC2_IN4, DAC1_OUT2 and WKUP6.
16 PA6 bidirectional 5 V-tolerant I/O (FT_fha) with Fm+ capability, high-speed low-voltage mode and analog switch supplied by VDDA; additional functions include OPAMP2_VINP, ADC1_IN9, ADC2_IN5 and WKUP7.
17 PA7 bidirectional 5 V-tolerant I/O (FT_fha) with Fm+ capability, high-speed low-voltage mode and analog switch supplied by VDDA; additional functions include OPAMP2_VINM, ADC1_IN10, ADC2_IN6 and WKUP8.
18 PB0 bidirectional 3.6 V-tolerant I/O (TT_ha) with high-speed low-voltage mode and analog switch supplied by VDDA; additional functions include OPAMP2_VOUT, ADC1_IN13 and ADC2_IN9.
19 PB1 bidirectional 5 V-tolerant I/O (FT_ha) with high-speed low-voltage mode and analog switch supplied by VDDA; additional functions include COMP1_INM1, ADC1_IN14, ADC2_IN10 and WKUP4.
20 VLXSMPS power_out Switched output of the SMPS step-down converter, connected through an external inductor (2.2 µH ±20%, ISAT > 0.5 A, DCR < 200 mΩ) to VDD11.
21 VDDSMPS power_in Supply input for the SMPS step-down converter, 1.71 V to 3.6 V; must be connected to VDD when the SMPS is used, and connected to GND together with VLXSMPS when it is not used.
22 VSSSMPS power_in SMPS ground pin; ground-pin variation between all VSSx pins and VSS must not exceed 50 mV.
23 VDD11 power_out SMPS output node requiring external capacitors of 2 × 2.2 µF ±20% (ESR < 20 mΩ at 3 MHz, rated voltage ≥ 10 V).
24 VSS power_in Ground pin; all voltages are referenced to VSS and ground pins must be connected to the external supply within the permitted range.
25 VDD power_in Main supply pin, 1.71 V to 3.6 V (functionality guaranteed down to VBOR min); supplies the I/Os, internal regulator and system analog.
26 PB13 bidirectional 5 V-tolerant I/O (FT_fha) with Fm+ capability and high-speed low-voltage mode; alternate functions include TIM1_CH1N, LPUART1_CTS and TIM15_CH1N.
27 PB14 bidirectional 5 V-tolerant I/O (FT_fha) with Fm+ capability and high-speed low-voltage mode; alternate functions include TIM1_CH2N, SPI2_MISO and TIM15_CH1.
28 PB15 bidirectional 5 V-tolerant I/O (FT_a) with analog switch function supplied by VDDA; additional functions include RTC_REFIN and WKUP7.
29 PA8 bidirectional 5 V-tolerant I/O (FT_h) with high-speed low-voltage mode; alternate functions include MCO, TIM1_CH1 and USART1_CK.
30 PA9 bidirectional 5 V-tolerant I/O (FT); alternate functions include MCO, TIM1_CH2 and USART1_TX (boot).
31 PA10 bidirectional 5 V-tolerant I/O (FT); alternate functions include CRS_SYNC, TIM1_CH3 and USART1_RX (boot).
32 PA11 bidirectional 5 V-tolerant I/O (FT_u) with USB function supplied by VDDUSB; additional function USB_DM (boot), alternate functions include TIM1_CH4 and USART1_CTS.
33 PA12 bidirectional 5 V-tolerant I/O (FT_u) with USB function supplied by VDDUSB; additional function USB_DP (boot), alternate functions include TIM1_ETR and USART1_RTS.
34 PA13 (JTMS/SWDIO) bidirectional 5 V-tolerant I/O that after reset is configured as JTMS/SWDIO with its internal pull-up activated.
35 VSS power_in Ground pin; all voltages are referenced to VSS.
36 VDD power_in Main supply pin, 1.71 V to 3.6 V, supplying the I/Os, internal regulator and system analog.
37 PA14 (JTCK/SWCLK) bidirectional 5 V-tolerant I/O that after reset is configured as JTCK/SWCLK with its internal pull-down activated.
38 PA15 (JTDI) bidirectional 5 V-tolerant I/O (FT_a) with analog switch function supplied by VDDA that after reset is configured as JTDI with its internal pull-up activated.
39 PB3 (JTDO/TRACESWO) bidirectional 5 V-tolerant I/O (FT_fha) with Fm+ capability and analog switch supplied by VDDA; additional function COMP2_INM2.
40 PB4 (NJTRST) bidirectional 5 V-tolerant I/O (FT_fha) with analog switch supplied by VDDA that after reset is configured as NJTRST with its internal pull-up activated.
41 PB5 bidirectional 5 V-tolerant I/O (FT_ha) with high-speed low-voltage mode and analog switch supplied by VDDA; additional function WKUP6.
42 PB6 bidirectional 5 V-tolerant I/O (FT_fha) with Fm+ capability and high-speed low-voltage mode; additional functions include COMP2_INP2 and WKUP3.
43 PB7 bidirectional 5 V-tolerant I/O (FT_fha) with Fm+ capability and high-speed low-voltage mode; additional functions include COMP2_INM1, PVD_IN and WKUP4.
44 PH3-BOOT0 bidirectional 5 V-tolerant I/O (FT_fh) that serves as the BOOT0 boot-selection pin on this package (boot function is available on all packages except WLCSP68 SMPS-G).
45 PB8 bidirectional 5 V-tolerant I/O (FT_fh) with Fm+ capability and high-speed low-voltage mode; additional function WKUP5, alternate functions include TIM4_CH3 and I2C1_SCL.
46 VDD11 power_out SMPS output node requiring external capacitors of 2 × 2.2 µF ±20% (ESR < 20 mΩ at 3 MHz, rated voltage ≥ 10 V).
47 VSS power_in Ground pin; all voltages are referenced to VSS.
48 VDD power_in Main supply pin, 1.71 V to 3.6 V, supplying the I/Os, internal regulator and system analog.

Key specifications

Parameter Value
Manufacturer STMicroelectronics
Package LQFP-48(7x7)
Category
Pins 48

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
External main supply voltage (VDD, VDDSMPS, VDDA, VDDUSB, VDDIO2, VBAT, VREF+) VDDX - VSS -0.3 4 V 96
I/O supply when HSLV = 0 VDDIOx - VSS -0.3 4 V HSLV = 0 97
I/O supply when HSLV = 1 VDDIOx - VSS -0.3 2.75 V HSLV = 1 97
Input voltage on PC13 and FT_o pins in VBAT mode VIN -0.3 4 V Min printed as VSS - 0.3 97
Input voltage on any other pins VIN -0.3 4 V Min printed as VSS - 0.3 97
Input voltage on FT_xx pins VIN -0.3 V Min printed as VSS - 0.3; max printed as Min(min(VDD, VDDA, VDDUSB, VDDIO2) + 4.0, 6.0), not computed 97
Allowed voltage difference for VREF+ > VDDA VREF+ - VDDA 0.4 V VREF+ > VDDA 97
Variations between different VDDx power pins of the same domain ΔVDDx 50 mV 97
Variations between all the different ground pins (including VREF-) VSSx - VSS 50 mV 97
Total current into sum of all VDD power lines (source) ∑IVDD 150 mA 97
Total current out of sum of all VSS ground lines (sink) ∑IVSS 150 mA 97
Maximum current into each VDD power pin (source) IVDD 100 mA 97
Maximum current out of each VSS ground pin (sink) IVSS 100 mA 97
Output current sunk by any I/O and control pin IIO 20 mA 97
Output current sourced by any I/O and control pin IIO 20 mA 97
Total output current sunk by sum of all I/Os and control pins ∑I(PIN) 120 mA 97
Total output current sourced by sum of all I/Os and control pins ∑I(PIN) 120 mA 97
Injected current on FT_xx, TT_xx, RST pins IINJ(PIN) -5 0 mA Printed as -5/+0 97
Total injected current (sum of all I/Os and control pins) ∑IINJ(PIN) -25 25 mA Printed as ±25 97
Storage temperature range TSTG -65 150 °C 97
Maximum junction temperature TJ 110 °C 97
Standard operating voltage VDD 1.71 3.6 V HSLV = 0 98
Standard operating voltage VDD 1.71 2.7 V HSLV = 1 98
Supply voltage for PG[15:2] I/Os VDDIO2 1.08 3.6 V At least one I/O in PG[15:2] used, HSLV = 0 98
Supply voltage for PG[15:2] I/Os VDDIO2 2.7 V At least one I/O in PG[15:2] used, HSLV = 1; single printed value assigned to min 98
Supply voltage for PG[15:2] I/Os VDDIO2 0 3.6 V PG[15:2] not used 98
USB supply voltage VDDUSB 3 3.6 V USB used 98
USB supply voltage VDDUSB 0 V USB not used; single printed value assigned to min 98
Analog supply voltage VDDA 1.58 3.6 V COMP used 98
Analog supply voltage VDDA 1.6 3.6 V DAC or OPAMP used 98
Analog supply voltage VDDA 1.62 3.6 V ADC used 98
Analog supply voltage VDDA 1.8 3.6 V VREFBUF used (normal mode) 98
Backup domain supply voltage VBAT 1.55 3.6 V 98
I/O input voltage VIN -0.3 V All I/Os except TT_xx pins; max printed as Min(min(VDD, VDDA, VDDUSB, VDDIO2) + 3.6, 5.5), not computed 98
I/O input voltage VIN -0.3 3.6 V Input voltage on PC13 and FT_o pins in VBAT mode 98
Sum of output current sourced by all I/Os powered by VSW IIO_SW 3 mA I/Os powered by VSW: PC13, PC14, PC15 98
Internal regulator core voltage VCORE 0.8 0.9 1 V Internal regulator ON, Range 1 98
Internal regulator core voltage VCORE 0.65 0.75 0.85 V Internal regulator ON, Range 2 98
AHB clock frequency fHCLK 96 MHz Range 1 98
AHB clock frequency fHCLK 48 MHz Range 2 98
APB1, APB2, APB3 clock frequency fPCLKx 96 MHz Range 1, x = 1, 2, 3 98
APB1, APB2, APB3 clock frequency fPCLKx 48 MHz Range 2, x = 1, 2, 3 98
Ambient temperature for suffix 6 TA -40 85 °C Maximum power dissipation 99
Ambient temperature for suffix 6 TA 105 °C Low-power dissipation 99
Junction temperature range, suffix 6 version TJ -40 105 °C Suffix 6 version 99
VDD rise-time rate tVDD 0 µs/V Max printed as ∞ 100
VDD fall-time rate tVDD 20 µs/V ULPMEN = 0; max printed as ∞ 100
VDD fall-time rate tVDD 250 ms/V Standby mode, BOR level 0 selected with ULPMEN = 1; max printed as ∞ 100
Reset temporization after BOR0 released tRSTTEMPO 900 µs VDD rising 100
Brownout reset threshold 0 VBOR0 1.63 1.65 1.67 V Rising edge 100
Brownout reset threshold 0 VBOR0 1.62 1.63 1.65 V Falling edge, Range 1 100
Internal reference voltage VREFINT 1.175 1.215 1.243 V Range 1 102
Internal reference voltage VREFINT 1.17 1.215 1.248 V Range 2 and low-power modes 102
Average temperature coefficient Tcoeff 62 150 ppm/°C -40 °C ≤ TJ ≤ 110 °C 102
Average voltage coefficient VDDcoeff1 600 2300 ppm/V 3.0 V ≤ VDD ≤ 3.6 V for -40 °C ≤ TJ ≤ +110 °C 102
Average voltage coefficient VDDcoeff2 270 1150 ppm/V 1.8 V ≤ VDD ≤ 3.6 V for -40 °C ≤ TJ ≤ +110 °C 102
Supply current in Run mode on LDO, Range 1 IDD (Run) 4.6 6 mA fHCLK = fMSI 96 MHz, all peripherals disabled, flash bank 2 powered down, all SRAMs enabled; typ at 25 °C, max at 30 °C 103
Supply current in Standby mode, no independent watchdog IDD (Standby) 0.18 0.55 µA VDD = 3 V, PWR_CR1.ULPMEN = 1, RTC disabled; typ at 25 °C, max at 30 °C 120

CAD (KiCad official)

  • Symbol: STM32U385CGT6Q
  • Footprint: Package_QFP:LQFP-48_7x7mm_P0.5mm
  • 3D model: LQFP-48(7x7) (KiCad packages3D, STEP)
  • 3D model files: stm32u385cgt6q-etched.step / stm32u385cgt6q-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); stm32u385cgt6q.step / stm32u385cgt6q.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: STMicroelectronics datasheet (232 pp, sha256 e939cd842042f13b, retrieved 2026-11-13, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF