component
STM32L496RET6TR
Public Made by Adomby adom
STMicroelectronics Microcontroller Units (MCUs/MPUs/SOCs), LQFP-64(10x10). Pinout checked against ST's open pin data, KiCad symbol/footprint/3D.
main
Ray
Publish 0.1.0
b808e30
STM32L496RET6TR
STMicroelectronics · Microcontroller Units (MCUs/MPUs/SOCs) · LQFP-64(10x10)
STM32L496RET6TR from STMicroelectronics, in a LQFP-64(10x10). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model, then checked against ST open pin data). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VBAT | power_in | Backup-domain supply input for the RTC and backup registers, specified from 1.55 V to 3.6 V (Table 22); also RTC_TAMP3/WKUP3. |
| 2 | PC13 | bidirectional | 5 V-tolerant GPIO supplied through the power switch, so output speed must not exceed 2 MHz with a 30 pF load, the switch sinks only 3 mA, and it must not drive current sources; also RTC_TAMP1/RTC_TS/RTC_OUT/WKUP2. |
| 3 | PC14-OSC32_IN | bidirectional | GPIO on the backup power switch with the same 2 MHz / 30 pF / 3 mA output limits, used as LSE 32.768 kHz oscillator input OSC32_IN. |
| 4 | PC15-OSC32_OUT | bidirectional | GPIO on the backup power switch with the same 2 MHz / 30 pF / 3 mA output limits, used as LSE 32.768 kHz oscillator output OSC32_OUT. |
| 5 | PH0-OSC_IN | bidirectional | 5 V-tolerant (FT) GPIO that is also the HSE crystal oscillator input OSC_IN. |
| 6 | PH1-OSC_OUT | bidirectional | 5 V-tolerant (FT) GPIO that is also the HSE crystal oscillator output OSC_OUT. |
| 7 | NRST | bidirectional | Bidirectional reset pin with an embedded weak pull-up resistor. |
| 8 | PC0 | bidirectional | 5 V-tolerant GPIO with Fm+, LCD (VLCD) and analog-switch options, ADC123_INP1 analog input, and alternates LPTIM1_IN1, I2C3_SCL, I2C4_SCL, LPUART1_RX and LPTIM2_IN1. |
| 9 | PC1 | bidirectional | 5 V-tolerant GPIO with Fm+, LCD (VLCD) and analog-switch options, ADC123_INP2/ADC123_INN1 analog inputs, and alternates TRACED0, LPTIM1_OUT, I2C4_SDA, SPI2_MOSI, LPUART1_TX and SAI1_SD_A. |
| 10 | PC2 | bidirectional | 5 V-tolerant GPIO with LCD and analog-switch options, ADC123_INP3/ADC123_INN2 analog inputs, and alternates LPTIM1_IN2, SPI2_MISO, DFSDM1_CKOUT and LCD_SEG20. |
| 11 | PC3 | bidirectional | 5 V-tolerant GPIO with LCD and analog-switch options, ADC123_INP4/ADC123_INN3 analog inputs, and alternates LPTIM1_ETR, SPI2_MOSI, LCD_VLCD, SAI1_SD_A and LPTIM2_ETR. |
| 12 | VSSA/VREF- | power_in | Analog ground and negative ADC reference VREF-; VREF- can be internally connected to VSSA depending on the package. |
| 13 | VDDA/VREF+ | power_in | Analog supply (1.62 V to 3.6 V when ADC or COMP is used) and positive ADC reference VREF+, which may exceed VDDA by no more than 0.4 V. |
| 14 | PA0 | bidirectional | 5 V-tolerant GPIO with analog-switch (VDDA) option, OPAMP1_VINPP and ADC12_INP5/ADC12_INN4 analog inputs, and alternates TIM2_CH1, TIM8_ETR, USART2_CTS, UART4_TX and RTC_TAMP2/WKUP1. |
| 15 | PA1 | bidirectional | 5 V-tolerant GPIO with LCD and analog-switch options, OPAMP1_VINPM and ADC12_INP6/ADC12_INN5 analog inputs, and alternates TIM2_CH2, I2C1_SMBA, SPI1_SCK, USART2_RTS_DE and UART4_RX. |
| 16 | PA2 | bidirectional | 5 V-tolerant GPIO with LCD and analog-switch options, ADC12_INP7/ADC12_INN6 analog inputs and WKUP4/LSCO, and alternates TIM2_CH3, USART2_TX, LPUART1_TX, QUADSPI_BK1_NCS and LCD_SEG1. |
| 17 | PA3 | bidirectional | 3.6 V-tolerant GPIO (TT) with analog-switch option, OPAMP1_VOUT and ADC12_INP8/ADC12_INN7 analog functions, and alternates TIM2_CH4, USART2_RX, LPUART1_RX, QUADSPI_CLK and SAI1_MCLK_A. |
| 18 | VSS | power_in | Ground pin. |
| 19 | VDD | power_in | Main power supply, 1.71 V to 3.6 V (Table 22). |
| 20 | PA4 | bidirectional | 3.6 V-tolerant GPIO with analog-switch (VDDA) option, ADC12_INP9/ADC12_INN8 and DAC1_OUT1 analog functions, and alternates SPI1_NSS, SPI3_NSS, USART2_CK, DCMI_HSYNC, SAI1_FS_B and LPTIM2_OUT. |
| 21 | PA5 | bidirectional | 3.6 V-tolerant GPIO with analog-switch (VDDA) option, ADC12_INP10/ADC12_INN9 and DAC1_OUT2 analog functions, and alternates TIM2_CH1, TIM2_ETR, TIM8_CH1N, SPI1_SCK and LPTIM2_ETR. |
| 22 | PA6 | bidirectional | 5 V-tolerant GPIO with LCD and analog-switch options, OPAMP2_VINPP and ADC12_INP11/ADC12_INN10 analog inputs, and alternates TIM1_BKIN, TIM3_CH1, TIM8_BKIN, DCMI_PIXCLK, SPI1_MISO, USART3_CTS and LPUART1_CTS. |
| 23 | PA7 | bidirectional | 5 V-tolerant GPIO with Fm+, LCD and analog-switch options, OPAMP2_VINPM and ADC12_INP12/ADC12_INN11 analog inputs, and alternates TIM1_CH1N, TIM3_CH2, TIM8_CH1N, I2C3_SCL, SPI1_MOSI and QUADSPI_BK1_IO2. |
| 24 | PC4 | bidirectional | 5 V-tolerant GPIO with LCD and analog-switch options, COMP1_INPM and ADC12_INP13/ADC12_INN12 analog inputs, and alternates USART3_TX, QUADSPI_BK2_IO3 and LCD_SEG22. |
| 25 | PC5 | bidirectional | 5 V-tolerant GPIO with analog-switch option, COMP1_INPP, ADC12_INP14/ADC12_INN13 and WKUP5 analog/wakeup functions, and alternates USART3_RX and LCD_SEG23. |
| 26 | PB0 | bidirectional | 3.6 V-tolerant GPIO (TT) with analog-switch option, OPAMP2_VOUT and ADC12_INP15/ADC12_INN14 analog functions, and alternates TIM1_CH2N, TIM3_CH3, TIM8_CH2N, SPI1_NSS, USART3_CK, QUADSPI_BK1_IO1, COMP1_OUT and SAI1_EXTCLK. |
| 27 | PB1 | bidirectional | 5 V-tolerant GPIO with LCD and analog-switch options, COMP1_INPM and ADC12_INP16/ADC12_INN15 analog inputs, and alternates TIM1_CH3N, TIM3_CH4, TIM8_CH3N, DFSDM1_DATIN0, USART3_RTS_DE, LPUART1_RTS_DE and LPTIM2_IN1. |
| 28 | PB2 | bidirectional | 5 V-tolerant GPIO with LCD and analog-switch options, COMP1_INP analog input, and alternates RTC_OUT, LPTIM1_OUT, I2C3_SMBA, DFSDM1_CKIN0 and LCD_VLCD. |
| 29 | PB10 | bidirectional | 5 V-tolerant GPIO with Fm+ and LCD options, and alternates TIM2_CH3, I2C4_SCL, I2C2_SCL, SPI2_SCK, DFSDM1_DATIN7, USART3_TX, LPUART1_RX, TSC_SYNC, QUADSPI_CLK and COMP1_OUT. |
| 30 | PB11 | bidirectional | 5 V-tolerant GPIO with Fm+ and LCD options, and alternates TIM2_CH4, I2C4_SDA, I2C2_SDA, DFSDM1_CKIN7, USART3_RX, LPUART1_TX, QUADSPI_BK1_NCS and COMP2_OUT. |
| 31 | VSS | power_in | Ground pin. |
| 32 | VDD | power_in | Main power supply, 1.71 V to 3.6 V (Table 22). |
| 33 | PB12 | bidirectional | 5 V-tolerant GPIO with LCD option, and alternates TIM1_BKIN, TIM1_BKIN_COMP2, I2C2_SMBA, SPI2_NSS, DFSDM1_DATIN1, USART3_CK, LPUART1_RTS_DE, TSC_G1_IO1, CAN2_RX, LCD_SEG12 and SAI2_FS_A. |
| 34 | PB13 | bidirectional | 5 V-tolerant GPIO with Fm+ and LCD options, and alternates TIM1_CH1N, I2C2_SCL, SPI2_SCK, DFSDM1_CKIN1, USART3_CTS, LPUART1_CTS, TSC_G1_IO2, CAN2_TX, LCD_SEG13 and SAI2_SCK_A. |
| 35 | PB14 | bidirectional | 5 V-tolerant GPIO with Fm+ and LCD options, and alternates TIM1_CH2N, TIM8_CH2N, I2C2_SDA, SPI2_MISO, DFSDM1_DATIN2, USART3_RTS_DE, TSC_G1_IO3, LCD_SEG14 and TIM15_CH1. |
| 36 | PB15 | bidirectional | 5 V-tolerant GPIO with LCD option, RTC_REFIN input, and alternates TIM1_CH3N, TIM8_CH3N, SPI2_MOSI, DFSDM1_CKIN2, TSC_G1_IO4, LCD_SEG15, SAI2_SD_A and TIM15_CH2. |
| 37 | PC6 | bidirectional | 5 V-tolerant GPIO with LCD option, and alternates TIM3_CH1, TIM8_CH1, DFSDM1_CKIN3, TSC_G4_IO1, DCMI_D0, LCD_SEG24, SDMMC1_D6 and SAI2_MCLK_A. |
| 38 | PC7 | bidirectional | 5 V-tolerant GPIO with LCD option, and alternates TIM3_CH2, TIM8_CH2, DFSDM1_DATIN3, TSC_G4_IO2, DCMI_D1, LCD_SEG25, SDMMC1_D7 and SAI2_MCLK_B. |
| 39 | PC8 | bidirectional | 5 V-tolerant GPIO with LCD option, and alternates TIM3_CH3, TIM8_CH3, TSC_G4_IO3, DCMI_D2, LCD_SEG26 and SDMMC1_D0. |
| 40 | PC9 | bidirectional | 5 V-tolerant GPIO with Fm+ and LCD options, and alternates TIM8_BKIN2, TIM3_CH4, TIM8_CH4, DCMI_D3, I2C3_SDA, TSC_G4_IO4, OTG_FS_NOE, LCD_SEG27, SDMMC1_D1 and SAI2_EXTCLK. |
| 41 | PA8 | bidirectional | 5 V-tolerant GPIO with LCD option, and alternates MCO, TIM1_CH1, USART1_CK, OTG_FS_SOF, LCD_COM0, SWPMI1_IO, SAI1_SCK_A and LPTIM2_OUT. |
| 42 | PA9 | bidirectional | 5 V-tolerant GPIO with LCD and USB (VDDUSB) options, and alternates TIM1_CH2, SPI2_SCK, DCMI_D0, USART1_TX, LCD_COM1, SAI1_FS_A, TIM15_BKIN and OTG_FS_VBUS. |
| 43 | PA10 | bidirectional | 5 V-tolerant GPIO with LCD and USB (VDDUSB) options, and alternates TIM1_CH3, DCMI_D1, USART1_RX, OTG_FS_ID, LCD_COM2, SAI1_SD_A and TIM17_BKIN. |
| 44 | PA11 | bidirectional | 5 V-tolerant GPIO with USB (VDDUSB) option, and alternates TIM1_CH4, TIM1_BKIN2, SPI1_MISO, USART1_CTS, CAN1_RX, OTG_FS_DM and TIM1_BKIN2_COMP1. |
| 45 | PA12 | bidirectional | 5 V-tolerant GPIO with USB (VDDUSB) option, and alternates TIM1_ETR, SPI1_MOSI, USART1_RTS_DE, CAN1_TX and OTG_FS_DP. |
| 46 | PA13 (JTMS/SWDIO) | bidirectional | 5 V-tolerant GPIO that after reset is the JTMS/SWDIO debug pin with the internal pull-up enabled; alternates IR_OUT, OTG_FS_NOE, SWPMI1_TX and SAI1_SD_B. |
| 47 | VSS | power_in | Ground pin. |
| 48 | VDDUSB | power_in | USB supply, 3.0 V to 3.6 V when USB is used (0 to 3.6 V when USB is not used) (Table 22). |
| 49 | PA14 (JTCK/SWCLK) | bidirectional | 5 V-tolerant GPIO that after reset is the JTCK/SWCLK debug pin with the internal pull-down enabled; alternates LPTIM1_OUT, I2C1_SMBA, I2C4_SMBA, OTG_FS_SOF, SWPMI1_RX and SAI1_FS_B. |
| 50 | PA15 (JTDI) | bidirectional | 5 V-tolerant GPIO that after reset is the JTDI debug pin with the internal pull-up enabled; alternates TIM2_CH1, TIM2_ETR, USART2_RX, SPI1_NSS, SPI3_NSS, LCD_SEG17 and SAI2_FS_B. |
| 51 | PC10 | bidirectional | 5 V-tolerant GPIO with LCD option, and alternates TRACED1, SPI3_SCK, USART3_TX, UART4_TX, TSC_G3_IO2, DCMI_D8, SDMMC1_D2 and SAI2_SCK_B. |
| 52 | PC11 | bidirectional | 5 V-tolerant GPIO with LCD option, and alternates QUADSPI_BK2_NCS, SPI3_MISO, USART3_RX, UART4_RX, TSC_G3_IO3, DCMI_D4, SDMMC1_D3 and SAI2_MCLK_B. |
| 53 | PC12 | bidirectional | 5 V-tolerant GPIO with LCD option, and alternates TRACED3, SPI3_MOSI, USART3_CK, UART5_TX, TSC_G3_IO4, DCMI_D9, SDMMC1_CK and SAI2_SD_B. |
| 54 | PD2 | bidirectional | 5 V-tolerant GPIO with LCD option, and alternates TRACED2, TIM3_ETR, USART3_RTS_DE, UART5_RX, TSC_SYNC, DCMI_D11 and SDMMC1_CMD. |
| 55 | PB3 (JTDO/TRACESWO) | bidirectional | 5 V-tolerant GPIO with analog-switch option, COMP2_INM analog input, which after reset is the JTDO/TRACESWO debug function; alternates TIM2_CH2, SPI1_SCK, SPI3_SCK, USART1_RTS_DE and SAI1_SCK_B. |
| 56 | PB4 (NJTRST) | bidirectional | 5 V-tolerant GPIO with Fm+, LCD and analog-switch options, COMP2_INP analog input, which after reset is the NJTRST debug pin with the internal pull-up enabled; alternates TIM3_CH1, I2C3_SDA, SPI1_MISO, SPI3_MISO, USART1_CTS, DCMI_D12 and TIM17_BKIN. |
| 57 | PB5 | bidirectional | 5 V-tolerant GPIO with analog-switch option, and alternates LPTIM1_IN1, TIM3_CH2, CAN2_RX, I2C1_SMBA, SPI1_MOSI, SPI3_MOSI, USART1_CK, UART5_CTS, TSC_G2_IO2, DCMI_D10, LCD_SEG9, COMP2_OUT, SAI1_SD_B and TIM16_BKIN. |
| 58 | PB6 | bidirectional | 5 V-tolerant GPIO with Fm+ and analog-switch (VDDA) options, COMP2_INP analog input, and alternates LPTIM1_ETR, TIM4_CH1, TIM8_BKIN2, I2C1_SCL, I2C4_SCL, DFSDM1_DATIN5, USART1_TX, CAN2_TX, DCMI_D5 and SAI1_FS_B. |
| 59 | PB7 | bidirectional | 5 V-tolerant GPIO with Fm+, LCD and analog-switch options, COMP2_INM and PVD_IN analog functions, and alternates LPTIM1_IN2, TIM4_CH2, TIM8_BKIN, I2C1_SDA, I2C4_SDA, DFSDM1_CKIN5, USART1_RX, UART4_CTS, TSC_G2_IO4, DCMI_VSYNC, LCD_SEG21 and FMC_NL. |
| 60 | PH3-BOOT0 | bidirectional | 5 V-tolerant GPIO that is also the BOOT0 boot-mode input; the BOOT0 input is specified up to 9.0 V (Table 19 and Table 22). |
| 61 | PB8 | bidirectional | 5 V-tolerant GPIO with Fm+ and LCD options, and alternates TIM4_CH3, I2C1_SCL, DFSDM1_DATIN6, CAN1_RX, DCMI_D6, LCD_SEG16, SDMMC1_D4, SAI1_MCLK_A and TIM16_CH1. |
| 62 | PB9 | bidirectional | 5 V-tolerant GPIO with Fm+ and LCD options, and alternates IR_OUT, TIM4_CH4, I2C1_SDA, SPI2_NSS, DFSDM1_CKIN6, CAN1_TX, DCMI_D7, LCD_COM3, SDMMC1_D5, SAI1_FS_A and TIM17_CH1. |
| 63 | VSS | power_in | Ground pin. |
| 64 | VDD | power_in | Main power supply, 1.71 V to 3.6 V (Table 22). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | LQFP-64(10x10) |
| Category | Single Chip Microcomputer/Microcontroller |
| Pins | 64 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Standard operating voltage (fHCLK internal AHB clock frequency) | fHCLK | 0 | 80 | MHz | 126 | ||
| Standard operating voltage | VDD | 1.71 | 3.6 | V | 126 | ||
| Standard operating voltage | VDD12 | 1.08 | 1.32 | V | Full frequency range | 126 | |
| Standard operating voltage | VDD12 | 1.05 | V | Up to 26 MHz | 126 | ||
| PG[15:2] I/Os supply voltage | VDDIO2 | 1.08 | 3.6 | V | At least one I/O in PG[15:2] used | 126 | |
| PG[15:2] I/Os supply voltage | VDDIO2 | 0 | 3.6 | V | PG[15:2] not used | 126 | |
| Analog supply voltage | VDDA | 1.62 | 3.6 | V | ADC or COMP used | 126 | |
| Analog supply voltage | VDDA | 1.8 | V | DAC or OPAMP used | 126 | ||
| Analog supply voltage | VDDA | 2.4 | V | VREFBUF used | 126 | ||
| Backup operating voltage | VBAT | 1.55 | 3.6 | V | 126 | ||
| USB supply voltage | VDDUSB | 3 | 3.6 | V | USB used | 126 | |
| I/O input voltage (BOOT0) | VIN | 0 | 9 | V | BOOT0 | 126 | |
| I/O input voltage (TT_xx I/O) | VIN | -0.3 | V | TT_xx I/O; max printed as VDDIOx+0.3 (formula) | 126 | ||
| I/O input voltage (all I/O except BOOT0 and TT_xx) | VIN | -0.3 | V | Max printed as Min(Min(VDD, VDDA, VDDIO2, VDDUSB, VLCD)+3.6 V, 5.5 V) (formula) | 126 | ||
| Ambient temperature for the suffix 6 version (maximum power dissipation) | TA | -40 | 85 | °C | Suffix 6, maximum power dissipation | 127 | |
| Ambient temperature for the suffix 6 version (low-power dissipation) | TA | -40 | 105 | °C | Suffix 6, low-power dissipation | 127 | |
| Junction temperature range (suffix 6 version) | TJ | -40 | 105 | °C | Suffix 6 version | 127 | |
| Power dissipation at TA = 85 °C for suffix 6 (LQFP64) | PD | 444 | mW | TA = 85 °C, suffix 6, LQFP64 | 127 | ||
| External main supply voltage (VDD, VDDA, VDDIO2, VDDUSB, VLCD, VBAT, VREF+) | VDDX - VSS | -0.3 | 4 | V | 124 | ||
| External SMPS supply voltage | VDD12 - VSS | -0.3 | 1.4 | V | Range 1 | 124 | |
| Input voltage on FT_xxx pins | VIN | -0.3 | V | Max printed as min(VDD, VDDA, VDDIO2, VDDUSB, VLCD) + 4.0 (formula) | 124 | ||
| Input voltage on TT_xx pins | VIN | -0.3 | 4 | V | 124 | ||
| Input voltage on BOOT0 pin | VIN | 9 | V | Min printed as VSS | 124 | ||
| Input voltage on any other pins | VIN | -0.3 | 4 | V | 124 | ||
| Variations between different VDDX power pins of the same domain | /ΔVDDx/ | 50 | mV | 125 | |||
| Variations between all the different ground pins (include VREF- pin) | /VSSx-VSS/ | 50 | mV | 125 | |||
| Allowed voltage difference for VREF+ > VDDA | VREF+ - VDDA | 0.4 | V | 125 | |||
| Total current into sum of all VDD power lines (source) | ∑IVDD | 150 | mA | 125 | |||
| Total current out of sum of all VSS ground lines (sink) | ∑IVSS | 150 | mA | 125 | |||
| Maximum current into each VDD power pin (source) | IVDD(PIN) | 100 | mA | 125 | |||
| Maximum current out of each VSS ground pin (sink) | IVSS(PIN) | 100 | mA | 125 | |||
| Output current sunk by any I/O and control pin except FT_f | IIO(PIN) | 20 | mA | 125 | |||
| Output current sunk by any FT_f pin | IIO(PIN) | 20 | mA | 125 | |||
| Output current sourced by any I/O and control pin | IIO(PIN) | 20 | mA | 125 | |||
| Total output current sunk by sum of all I/Os and control pins | ∑IIO(PIN) | 100 | mA | 125 | |||
| Total output current sourced by sum of all I/Os and control pins | ∑IIO(PIN) | 100 | mA | 125 | |||
| Injected current on FT_xxx, TT_xx, RST and B pins, except PA4, PA5 | IINJ(PIN) | -5 | 0 | mA | Printed as -5/+0 | 125 | |
| Injected current on PA4, PA5 | IINJ(PIN) | -5 | 0 | mA | Printed as -5/0 | 125 | |
| Total injected current (sum of all I/Os and control pins) | ∑/IINJ(PIN)/ | 25 | mA | 125 | |||
| Storage temperature range | TSTG | -65 | 150 | °C | 126 | ||
| Maximum junction temperature | TJ | 150 | °C | 126 | |||
| Reset temporization after BOR0 is detected | tRSTTEMPO | 250 | 400 | µs | VDD rising | 128 | |
| Brown-out reset threshold 0 | VBOR0 | 1.62 | 1.66 | 1.7 | V | Rising edge | 128 |
| Brown-out reset threshold 0 | VBOR0 | 1.6 | 1.64 | 1.69 | V | Falling edge | 128 |
| Brown-out reset threshold 1 | VBOR1 | 2.06 | 2.1 | 2.14 | V | Rising edge | 128 |
| Brown-out reset threshold 1 | VBOR1 | 1.96 | 2 | 2.04 | V | Falling edge | 128 |
| BOR (except BOR0) and PVD consumption from VDD | IDD(BOR_PVD) | 1.1 | 1.6 | µA | Guaranteed by design | 129 | |
| Internal reference voltage | VREFINT | 1.182 | 1.212 | 1.232 | V | -40 °C < TA < +130 °C | 130 |
| ADC sampling time when reading the internal reference voltage | tS_vrefint | 4 | µs | Guaranteed by design | 130 | ||
| Start time of reference voltage buffer when ADC is enabled | tstart_vrefint | 8 | 12 | µs | Guaranteed by design (max) | 130 | |
| VREFINT buffer consumption from VDD when converted by ADC | IDD(VREFINTBUF) | 12.5 | 20 | µA | Guaranteed by design (max) | 130 | |
| Internal reference voltage spread over the temperature range | ΔVREFINT | 5 | 7.5 | mV | VDD = 3 V; max guaranteed by design | 130 | |
| Average temperature coefficient | TCoeff | 30 | 50 | ppm/°C | -40°C < TA < +130°C; max guaranteed by design | 130 | |
| Long term stability | ACoeff | 300 | 1000 | ppm | 1000 hours, T = 25°C; max guaranteed by design | 130 | |
| Average voltage coefficient | VDDCoeff | 250 | 1200 | ppm/V | 3.0 V < VDD < 3.6 V; max guaranteed by design | 130 | |
| 1/4 reference voltage | VREFINT_DIV1 | 24 | 25 | 26 | % | Fraction of VREFINT | 130 |
| 1/2 reference voltage | VREFINT_DIV2 | 49 | 50 | 51 | % | Fraction of VREFINT | 130 |
| 3/4 reference voltage | VREFINT_DIV3 | 74 | 75 | 76 | % | Fraction of VREFINT | 130 |
CAD (KiCad official)
- Symbol:
STM32L496RET6TR - Footprint:
Package_QFP:LQFP-64_10x10mm_P0.5mm - 3D model: LQFP-64(10x10) (KiCad packages3D, STEP)
- 3D model files:
stm32l496ret6tr-etched.step/stm32l496ret6tr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);stm32l496ret6tr.step/stm32l496ret6tr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: STMicroelectronics datasheet (280 pp, sha256
07777c1c9ca126d7, retrieved 2026-11-13, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# STM32L496RET6TR
**STMicroelectronics** · Microcontroller Units (MCUs/MPUs/SOCs) · LQFP-64(10x10)
STM32L496RET6TR from STMicroelectronics, in a LQFP-64(10x10). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model, then checked against ST open pin data). Symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VBAT | power_in | Backup-domain supply input for the RTC and backup registers, specified from 1.55 V to 3.6 V (Table 22); also RTC_TAMP3/WKUP3. |
| 2 | PC13 | bidirectional | 5 V-tolerant GPIO supplied through the power switch, so output speed must not exceed 2 MHz with a 30 pF load, the switch sinks only 3 mA, and it must not drive current sources; also RTC_TAMP1/RTC_TS/RTC_OUT/WKUP2. |
| 3 | PC14-OSC32_IN | bidirectional | GPIO on the backup power switch with the same 2 MHz / 30 pF / 3 mA output limits, used as LSE 32.768 kHz oscillator input OSC32_IN. |
| 4 | PC15-OSC32_OUT | bidirectional | GPIO on the backup power switch with the same 2 MHz / 30 pF / 3 mA output limits, used as LSE 32.768 kHz oscillator output OSC32_OUT. |
| 5 | PH0-OSC_IN | bidirectional | 5 V-tolerant (FT) GPIO that is also the HSE crystal oscillator input OSC_IN. |
| 6 | PH1-OSC_OUT | bidirectional | 5 V-tolerant (FT) GPIO that is also the HSE crystal oscillator output OSC_OUT. |
| 7 | NRST | bidirectional | Bidirectional reset pin with an embedded weak pull-up resistor. |
| 8 | PC0 | bidirectional | 5 V-tolerant GPIO with Fm+, LCD (VLCD) and analog-switch options, ADC123_INP1 analog input, and alternates LPTIM1_IN1, I2C3_SCL, I2C4_SCL, LPUART1_RX and LPTIM2_IN1. |
| 9 | PC1 | bidirectional | 5 V-tolerant GPIO with Fm+, LCD (VLCD) and analog-switch options, ADC123_INP2/ADC123_INN1 analog inputs, and alternates TRACED0, LPTIM1_OUT, I2C4_SDA, SPI2_MOSI, LPUART1_TX and SAI1_SD_A. |
| 10 | PC2 | bidirectional | 5 V-tolerant GPIO with LCD and analog-switch options, ADC123_INP3/ADC123_INN2 analog inputs, and alternates LPTIM1_IN2, SPI2_MISO, DFSDM1_CKOUT and LCD_SEG20. |
| 11 | PC3 | bidirectional | 5 V-tolerant GPIO with LCD and analog-switch options, ADC123_INP4/ADC123_INN3 analog inputs, and alternates LPTIM1_ETR, SPI2_MOSI, LCD_VLCD, SAI1_SD_A and LPTIM2_ETR. |
| 12 | VSSA/VREF- | power_in | Analog ground and negative ADC reference VREF-; VREF- can be internally connected to VSSA depending on the package. |
| 13 | VDDA/VREF+ | power_in | Analog supply (1.62 V to 3.6 V when ADC or COMP is used) and positive ADC reference VREF+, which may exceed VDDA by no more than 0.4 V. |
| 14 | PA0 | bidirectional | 5 V-tolerant GPIO with analog-switch (VDDA) option, OPAMP1_VINPP and ADC12_INP5/ADC12_INN4 analog inputs, and alternates TIM2_CH1, TIM8_ETR, USART2_CTS, UART4_TX and RTC_TAMP2/WKUP1. |
| 15 | PA1 | bidirectional | 5 V-tolerant GPIO with LCD and analog-switch options, OPAMP1_VINPM and ADC12_INP6/ADC12_INN5 analog inputs, and alternates TIM2_CH2, I2C1_SMBA, SPI1_SCK, USART2_RTS_DE and UART4_RX. |
| 16 | PA2 | bidirectional | 5 V-tolerant GPIO with LCD and analog-switch options, ADC12_INP7/ADC12_INN6 analog inputs and WKUP4/LSCO, and alternates TIM2_CH3, USART2_TX, LPUART1_TX, QUADSPI_BK1_NCS and LCD_SEG1. |
| 17 | PA3 | bidirectional | 3.6 V-tolerant GPIO (TT) with analog-switch option, OPAMP1_VOUT and ADC12_INP8/ADC12_INN7 analog functions, and alternates TIM2_CH4, USART2_RX, LPUART1_RX, QUADSPI_CLK and SAI1_MCLK_A. |
| 18 | VSS | power_in | Ground pin. |
| 19 | VDD | power_in | Main power supply, 1.71 V to 3.6 V (Table 22). |
| 20 | PA4 | bidirectional | 3.6 V-tolerant GPIO with analog-switch (VDDA) option, ADC12_INP9/ADC12_INN8 and DAC1_OUT1 analog functions, and alternates SPI1_NSS, SPI3_NSS, USART2_CK, DCMI_HSYNC, SAI1_FS_B and LPTIM2_OUT. |
| 21 | PA5 | bidirectional | 3.6 V-tolerant GPIO with analog-switch (VDDA) option, ADC12_INP10/ADC12_INN9 and DAC1_OUT2 analog functions, and alternates TIM2_CH1, TIM2_ETR, TIM8_CH1N, SPI1_SCK and LPTIM2_ETR. |
| 22 | PA6 | bidirectional | 5 V-tolerant GPIO with LCD and analog-switch options, OPAMP2_VINPP and ADC12_INP11/ADC12_INN10 analog inputs, and alternates TIM1_BKIN, TIM3_CH1, TIM8_BKIN, DCMI_PIXCLK, SPI1_MISO, USART3_CTS and LPUART1_CTS. |
| 23 | PA7 | bidirectional | 5 V-tolerant GPIO with Fm+, LCD and analog-switch options, OPAMP2_VINPM and ADC12_INP12/ADC12_INN11 analog inputs, and alternates TIM1_CH1N, TIM3_CH2, TIM8_CH1N, I2C3_SCL, SPI1_MOSI and QUADSPI_BK1_IO2. |
| 24 | PC4 | bidirectional | 5 V-tolerant GPIO with LCD and analog-switch options, COMP1_INPM and ADC12_INP13/ADC12_INN12 analog inputs, and alternates USART3_TX, QUADSPI_BK2_IO3 and LCD_SEG22. |
| 25 | PC5 | bidirectional | 5 V-tolerant GPIO with analog-switch option, COMP1_INPP, ADC12_INP14/ADC12_INN13 and WKUP5 analog/wakeup functions, and alternates USART3_RX and LCD_SEG23. |
| 26 | PB0 | bidirectional | 3.6 V-tolerant GPIO (TT) with analog-switch option, OPAMP2_VOUT and ADC12_INP15/ADC12_INN14 analog functions, and alternates TIM1_CH2N, TIM3_CH3, TIM8_CH2N, SPI1_NSS, USART3_CK, QUADSPI_BK1_IO1, COMP1_OUT and SAI1_EXTCLK. |
| 27 | PB1 | bidirectional | 5 V-tolerant GPIO with LCD and analog-switch options, COMP1_INPM and ADC12_INP16/ADC12_INN15 analog inputs, and alternates TIM1_CH3N, TIM3_CH4, TIM8_CH3N, DFSDM1_DATIN0, USART3_RTS_DE, LPUART1_RTS_DE and LPTIM2_IN1. |
| 28 | PB2 | bidirectional | 5 V-tolerant GPIO with LCD and analog-switch options, COMP1_INP analog input, and alternates RTC_OUT, LPTIM1_OUT, I2C3_SMBA, DFSDM1_CKIN0 and LCD_VLCD. |
| 29 | PB10 | bidirectional | 5 V-tolerant GPIO with Fm+ and LCD options, and alternates TIM2_CH3, I2C4_SCL, I2C2_SCL, SPI2_SCK, DFSDM1_DATIN7, USART3_TX, LPUART1_RX, TSC_SYNC, QUADSPI_CLK and COMP1_OUT. |
| 30 | PB11 | bidirectional | 5 V-tolerant GPIO with Fm+ and LCD options, and alternates TIM2_CH4, I2C4_SDA, I2C2_SDA, DFSDM1_CKIN7, USART3_RX, LPUART1_TX, QUADSPI_BK1_NCS and COMP2_OUT. |
| 31 | VSS | power_in | Ground pin. |
| 32 | VDD | power_in | Main power supply, 1.71 V to 3.6 V (Table 22). |
| 33 | PB12 | bidirectional | 5 V-tolerant GPIO with LCD option, and alternates TIM1_BKIN, TIM1_BKIN_COMP2, I2C2_SMBA, SPI2_NSS, DFSDM1_DATIN1, USART3_CK, LPUART1_RTS_DE, TSC_G1_IO1, CAN2_RX, LCD_SEG12 and SAI2_FS_A. |
| 34 | PB13 | bidirectional | 5 V-tolerant GPIO with Fm+ and LCD options, and alternates TIM1_CH1N, I2C2_SCL, SPI2_SCK, DFSDM1_CKIN1, USART3_CTS, LPUART1_CTS, TSC_G1_IO2, CAN2_TX, LCD_SEG13 and SAI2_SCK_A. |
| 35 | PB14 | bidirectional | 5 V-tolerant GPIO with Fm+ and LCD options, and alternates TIM1_CH2N, TIM8_CH2N, I2C2_SDA, SPI2_MISO, DFSDM1_DATIN2, USART3_RTS_DE, TSC_G1_IO3, LCD_SEG14 and TIM15_CH1. |
| 36 | PB15 | bidirectional | 5 V-tolerant GPIO with LCD option, RTC_REFIN input, and alternates TIM1_CH3N, TIM8_CH3N, SPI2_MOSI, DFSDM1_CKIN2, TSC_G1_IO4, LCD_SEG15, SAI2_SD_A and TIM15_CH2. |
| 37 | PC6 | bidirectional | 5 V-tolerant GPIO with LCD option, and alternates TIM3_CH1, TIM8_CH1, DFSDM1_CKIN3, TSC_G4_IO1, DCMI_D0, LCD_SEG24, SDMMC1_D6 and SAI2_MCLK_A. |
| 38 | PC7 | bidirectional | 5 V-tolerant GPIO with LCD option, and alternates TIM3_CH2, TIM8_CH2, DFSDM1_DATIN3, TSC_G4_IO2, DCMI_D1, LCD_SEG25, SDMMC1_D7 and SAI2_MCLK_B. |
| 39 | PC8 | bidirectional | 5 V-tolerant GPIO with LCD option, and alternates TIM3_CH3, TIM8_CH3, TSC_G4_IO3, DCMI_D2, LCD_SEG26 and SDMMC1_D0. |
| 40 | PC9 | bidirectional | 5 V-tolerant GPIO with Fm+ and LCD options, and alternates TIM8_BKIN2, TIM3_CH4, TIM8_CH4, DCMI_D3, I2C3_SDA, TSC_G4_IO4, OTG_FS_NOE, LCD_SEG27, SDMMC1_D1 and SAI2_EXTCLK. |
| 41 | PA8 | bidirectional | 5 V-tolerant GPIO with LCD option, and alternates MCO, TIM1_CH1, USART1_CK, OTG_FS_SOF, LCD_COM0, SWPMI1_IO, SAI1_SCK_A and LPTIM2_OUT. |
| 42 | PA9 | bidirectional | 5 V-tolerant GPIO with LCD and USB (VDDUSB) options, and alternates TIM1_CH2, SPI2_SCK, DCMI_D0, USART1_TX, LCD_COM1, SAI1_FS_A, TIM15_BKIN and OTG_FS_VBUS. |
| 43 | PA10 | bidirectional | 5 V-tolerant GPIO with LCD and USB (VDDUSB) options, and alternates TIM1_CH3, DCMI_D1, USART1_RX, OTG_FS_ID, LCD_COM2, SAI1_SD_A and TIM17_BKIN. |
| 44 | PA11 | bidirectional | 5 V-tolerant GPIO with USB (VDDUSB) option, and alternates TIM1_CH4, TIM1_BKIN2, SPI1_MISO, USART1_CTS, CAN1_RX, OTG_FS_DM and TIM1_BKIN2_COMP1. |
| 45 | PA12 | bidirectional | 5 V-tolerant GPIO with USB (VDDUSB) option, and alternates TIM1_ETR, SPI1_MOSI, USART1_RTS_DE, CAN1_TX and OTG_FS_DP. |
| 46 | PA13 (JTMS/SWDIO) | bidirectional | 5 V-tolerant GPIO that after reset is the JTMS/SWDIO debug pin with the internal pull-up enabled; alternates IR_OUT, OTG_FS_NOE, SWPMI1_TX and SAI1_SD_B. |
| 47 | VSS | power_in | Ground pin. |
| 48 | VDDUSB | power_in | USB supply, 3.0 V to 3.6 V when USB is used (0 to 3.6 V when USB is not used) (Table 22). |
| 49 | PA14 (JTCK/SWCLK) | bidirectional | 5 V-tolerant GPIO that after reset is the JTCK/SWCLK debug pin with the internal pull-down enabled; alternates LPTIM1_OUT, I2C1_SMBA, I2C4_SMBA, OTG_FS_SOF, SWPMI1_RX and SAI1_FS_B. |
| 50 | PA15 (JTDI) | bidirectional | 5 V-tolerant GPIO that after reset is the JTDI debug pin with the internal pull-up enabled; alternates TIM2_CH1, TIM2_ETR, USART2_RX, SPI1_NSS, SPI3_NSS, LCD_SEG17 and SAI2_FS_B. |
| 51 | PC10 | bidirectional | 5 V-tolerant GPIO with LCD option, and alternates TRACED1, SPI3_SCK, USART3_TX, UART4_TX, TSC_G3_IO2, DCMI_D8, SDMMC1_D2 and SAI2_SCK_B. |
| 52 | PC11 | bidirectional | 5 V-tolerant GPIO with LCD option, and alternates QUADSPI_BK2_NCS, SPI3_MISO, USART3_RX, UART4_RX, TSC_G3_IO3, DCMI_D4, SDMMC1_D3 and SAI2_MCLK_B. |
| 53 | PC12 | bidirectional | 5 V-tolerant GPIO with LCD option, and alternates TRACED3, SPI3_MOSI, USART3_CK, UART5_TX, TSC_G3_IO4, DCMI_D9, SDMMC1_CK and SAI2_SD_B. |
| 54 | PD2 | bidirectional | 5 V-tolerant GPIO with LCD option, and alternates TRACED2, TIM3_ETR, USART3_RTS_DE, UART5_RX, TSC_SYNC, DCMI_D11 and SDMMC1_CMD. |
| 55 | PB3 (JTDO/TRACESWO) | bidirectional | 5 V-tolerant GPIO with analog-switch option, COMP2_INM analog input, which after reset is the JTDO/TRACESWO debug function; alternates TIM2_CH2, SPI1_SCK, SPI3_SCK, USART1_RTS_DE and SAI1_SCK_B. |
| 56 | PB4 (NJTRST) | bidirectional | 5 V-tolerant GPIO with Fm+, LCD and analog-switch options, COMP2_INP analog input, which after reset is the NJTRST debug pin with the internal pull-up enabled; alternates TIM3_CH1, I2C3_SDA, SPI1_MISO, SPI3_MISO, USART1_CTS, DCMI_D12 and TIM17_BKIN. |
| 57 | PB5 | bidirectional | 5 V-tolerant GPIO with analog-switch option, and alternates LPTIM1_IN1, TIM3_CH2, CAN2_RX, I2C1_SMBA, SPI1_MOSI, SPI3_MOSI, USART1_CK, UART5_CTS, TSC_G2_IO2, DCMI_D10, LCD_SEG9, COMP2_OUT, SAI1_SD_B and TIM16_BKIN. |
| 58 | PB6 | bidirectional | 5 V-tolerant GPIO with Fm+ and analog-switch (VDDA) options, COMP2_INP analog input, and alternates LPTIM1_ETR, TIM4_CH1, TIM8_BKIN2, I2C1_SCL, I2C4_SCL, DFSDM1_DATIN5, USART1_TX, CAN2_TX, DCMI_D5 and SAI1_FS_B. |
| 59 | PB7 | bidirectional | 5 V-tolerant GPIO with Fm+, LCD and analog-switch options, COMP2_INM and PVD_IN analog functions, and alternates LPTIM1_IN2, TIM4_CH2, TIM8_BKIN, I2C1_SDA, I2C4_SDA, DFSDM1_CKIN5, USART1_RX, UART4_CTS, TSC_G2_IO4, DCMI_VSYNC, LCD_SEG21 and FMC_NL. |
| 60 | PH3-BOOT0 | bidirectional | 5 V-tolerant GPIO that is also the BOOT0 boot-mode input; the BOOT0 input is specified up to 9.0 V (Table 19 and Table 22). |
| 61 | PB8 | bidirectional | 5 V-tolerant GPIO with Fm+ and LCD options, and alternates TIM4_CH3, I2C1_SCL, DFSDM1_DATIN6, CAN1_RX, DCMI_D6, LCD_SEG16, SDMMC1_D4, SAI1_MCLK_A and TIM16_CH1. |
| 62 | PB9 | bidirectional | 5 V-tolerant GPIO with Fm+ and LCD options, and alternates IR_OUT, TIM4_CH4, I2C1_SDA, SPI2_NSS, DFSDM1_CKIN6, CAN1_TX, DCMI_D7, LCD_COM3, SDMMC1_D5, SAI1_FS_A and TIM17_CH1. |
| 63 | VSS | power_in | Ground pin. |
| 64 | VDD | power_in | Main power supply, 1.71 V to 3.6 V (Table 22). |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | LQFP-64(10x10) |
| Category | Single Chip Microcomputer/Microcontroller |
| Pins | 64 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Standard operating voltage (fHCLK internal AHB clock frequency) | fHCLK | 0 | | 80 | MHz | | 126 |
| Standard operating voltage | VDD | 1.71 | | 3.6 | V | | 126 |
| Standard operating voltage | VDD12 | 1.08 | | 1.32 | V | Full frequency range | 126 |
| Standard operating voltage | VDD12 | 1.05 | | | V | Up to 26 MHz | 126 |
| PG[15:2] I/Os supply voltage | VDDIO2 | 1.08 | | 3.6 | V | At least one I/O in PG[15:2] used | 126 |
| PG[15:2] I/Os supply voltage | VDDIO2 | 0 | | 3.6 | V | PG[15:2] not used | 126 |
| Analog supply voltage | VDDA | 1.62 | | 3.6 | V | ADC or COMP used | 126 |
| Analog supply voltage | VDDA | 1.8 | | | V | DAC or OPAMP used | 126 |
| Analog supply voltage | VDDA | 2.4 | | | V | VREFBUF used | 126 |
| Backup operating voltage | VBAT | 1.55 | | 3.6 | V | | 126 |
| USB supply voltage | VDDUSB | 3 | | 3.6 | V | USB used | 126 |
| I/O input voltage (BOOT0) | VIN | 0 | | 9 | V | BOOT0 | 126 |
| I/O input voltage (TT_xx I/O) | VIN | -0.3 | | | V | TT_xx I/O; max printed as VDDIOx+0.3 (formula) | 126 |
| I/O input voltage (all I/O except BOOT0 and TT_xx) | VIN | -0.3 | | | V | Max printed as Min(Min(VDD, VDDA, VDDIO2, VDDUSB, VLCD)+3.6 V, 5.5 V) (formula) | 126 |
| Ambient temperature for the suffix 6 version (maximum power dissipation) | TA | -40 | | 85 | °C | Suffix 6, maximum power dissipation | 127 |
| Ambient temperature for the suffix 6 version (low-power dissipation) | TA | -40 | | 105 | °C | Suffix 6, low-power dissipation | 127 |
| Junction temperature range (suffix 6 version) | TJ | -40 | | 105 | °C | Suffix 6 version | 127 |
| Power dissipation at TA = 85 °C for suffix 6 (LQFP64) | PD | | | 444 | mW | TA = 85 °C, suffix 6, LQFP64 | 127 |
| External main supply voltage (VDD, VDDA, VDDIO2, VDDUSB, VLCD, VBAT, VREF+) | VDDX - VSS | -0.3 | | 4 | V | | 124 |
| External SMPS supply voltage | VDD12 - VSS | -0.3 | | 1.4 | V | Range 1 | 124 |
| Input voltage on FT_xxx pins | VIN | -0.3 | | | V | Max printed as min(VDD, VDDA, VDDIO2, VDDUSB, VLCD) + 4.0 (formula) | 124 |
| Input voltage on TT_xx pins | VIN | -0.3 | | 4 | V | | 124 |
| Input voltage on BOOT0 pin | VIN | | | 9 | V | Min printed as VSS | 124 |
| Input voltage on any other pins | VIN | -0.3 | | 4 | V | | 124 |
| Variations between different VDDX power pins of the same domain | /ΔVDDx/ | | | 50 | mV | | 125 |
| Variations between all the different ground pins (include VREF- pin) | /VSSx-VSS/ | | | 50 | mV | | 125 |
| Allowed voltage difference for VREF+ > VDDA | VREF+ - VDDA | | | 0.4 | V | | 125 |
| Total current into sum of all VDD power lines (source) | ∑IVDD | | | 150 | mA | | 125 |
| Total current out of sum of all VSS ground lines (sink) | ∑IVSS | | | 150 | mA | | 125 |
| Maximum current into each VDD power pin (source) | IVDD(PIN) | | | 100 | mA | | 125 |
| Maximum current out of each VSS ground pin (sink) | IVSS(PIN) | | | 100 | mA | | 125 |
| Output current sunk by any I/O and control pin except FT_f | IIO(PIN) | | | 20 | mA | | 125 |
| Output current sunk by any FT_f pin | IIO(PIN) | | | 20 | mA | | 125 |
| Output current sourced by any I/O and control pin | IIO(PIN) | | | 20 | mA | | 125 |
| Total output current sunk by sum of all I/Os and control pins | ∑IIO(PIN) | | | 100 | mA | | 125 |
| Total output current sourced by sum of all I/Os and control pins | ∑IIO(PIN) | | | 100 | mA | | 125 |
| Injected current on FT_xxx, TT_xx, RST and B pins, except PA4, PA5 | IINJ(PIN) | -5 | | 0 | mA | Printed as -5/+0 | 125 |
| Injected current on PA4, PA5 | IINJ(PIN) | -5 | | 0 | mA | Printed as -5/0 | 125 |
| Total injected current (sum of all I/Os and control pins) | ∑/IINJ(PIN)/ | | | 25 | mA | | 125 |
| Storage temperature range | TSTG | -65 | | 150 | °C | | 126 |
| Maximum junction temperature | TJ | | | 150 | °C | | 126 |
| Reset temporization after BOR0 is detected | tRSTTEMPO | | 250 | 400 | µs | VDD rising | 128 |
| Brown-out reset threshold 0 | VBOR0 | 1.62 | 1.66 | 1.7 | V | Rising edge | 128 |
| Brown-out reset threshold 0 | VBOR0 | 1.6 | 1.64 | 1.69 | V | Falling edge | 128 |
| Brown-out reset threshold 1 | VBOR1 | 2.06 | 2.1 | 2.14 | V | Rising edge | 128 |
| Brown-out reset threshold 1 | VBOR1 | 1.96 | 2 | 2.04 | V | Falling edge | 128 |
| BOR (except BOR0) and PVD consumption from VDD | IDD(BOR_PVD) | | 1.1 | 1.6 | µA | Guaranteed by design | 129 |
| Internal reference voltage | VREFINT | 1.182 | 1.212 | 1.232 | V | -40 °C < TA < +130 °C | 130 |
| ADC sampling time when reading the internal reference voltage | tS_vrefint | 4 | | | µs | Guaranteed by design | 130 |
| Start time of reference voltage buffer when ADC is enabled | tstart_vrefint | | 8 | 12 | µs | Guaranteed by design (max) | 130 |
| VREFINT buffer consumption from VDD when converted by ADC | IDD(VREFINTBUF) | | 12.5 | 20 | µA | Guaranteed by design (max) | 130 |
| Internal reference voltage spread over the temperature range | ΔVREFINT | | 5 | 7.5 | mV | VDD = 3 V; max guaranteed by design | 130 |
| Average temperature coefficient | TCoeff | | 30 | 50 | ppm/°C | -40°C < TA < +130°C; max guaranteed by design | 130 |
| Long term stability | ACoeff | | 300 | 1000 | ppm | 1000 hours, T = 25°C; max guaranteed by design | 130 |
| Average voltage coefficient | VDDCoeff | | 250 | 1200 | ppm/V | 3.0 V < VDD < 3.6 V; max guaranteed by design | 130 |
| 1/4 reference voltage | VREFINT_DIV1 | 24 | 25 | 26 | % | Fraction of VREFINT | 130 |
| 1/2 reference voltage | VREFINT_DIV2 | 49 | 50 | 51 | % | Fraction of VREFINT | 130 |
| 3/4 reference voltage | VREFINT_DIV3 | 74 | 75 | 76 | % | Fraction of VREFINT | 130 |
## CAD (KiCad official)
- Symbol: `STM32L496RET6TR`
- Footprint: `Package_QFP:LQFP-64_10x10mm_P0.5mm`
- 3D model: LQFP-64(10x10) (KiCad packages3D, STEP)
- 3D model files: `stm32l496ret6tr-etched.step` / `stm32l496ret6tr-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `stm32l496ret6tr.step` / `stm32l496ret6tr.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [STMicroelectronics datasheet](https://www.st.com/resource/en/datasheet/stm32l496ae.pdf) (280 pp, sha256 `07777c1c9ca126d7`, retrieved 2026-11-13, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/stm32l496ret6tr-datasheet.pdf)