Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

STM32L496RET6TR

STMicroelectronics · Microcontroller Units (MCUs/MPUs/SOCs) · LQFP-64(10x10)

STM32L496RET6TR from STMicroelectronics, in a LQFP-64(10x10). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model, then checked against ST open pin data). Symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VBAT power_in Backup-domain supply input for the RTC and backup registers, specified from 1.55 V to 3.6 V (Table 22); also RTC_TAMP3/WKUP3.
2 PC13 bidirectional 5 V-tolerant GPIO supplied through the power switch, so output speed must not exceed 2 MHz with a 30 pF load, the switch sinks only 3 mA, and it must not drive current sources; also RTC_TAMP1/RTC_TS/RTC_OUT/WKUP2.
3 PC14-OSC32_IN bidirectional GPIO on the backup power switch with the same 2 MHz / 30 pF / 3 mA output limits, used as LSE 32.768 kHz oscillator input OSC32_IN.
4 PC15-OSC32_OUT bidirectional GPIO on the backup power switch with the same 2 MHz / 30 pF / 3 mA output limits, used as LSE 32.768 kHz oscillator output OSC32_OUT.
5 PH0-OSC_IN bidirectional 5 V-tolerant (FT) GPIO that is also the HSE crystal oscillator input OSC_IN.
6 PH1-OSC_OUT bidirectional 5 V-tolerant (FT) GPIO that is also the HSE crystal oscillator output OSC_OUT.
7 NRST bidirectional Bidirectional reset pin with an embedded weak pull-up resistor.
8 PC0 bidirectional 5 V-tolerant GPIO with Fm+, LCD (VLCD) and analog-switch options, ADC123_INP1 analog input, and alternates LPTIM1_IN1, I2C3_SCL, I2C4_SCL, LPUART1_RX and LPTIM2_IN1.
9 PC1 bidirectional 5 V-tolerant GPIO with Fm+, LCD (VLCD) and analog-switch options, ADC123_INP2/ADC123_INN1 analog inputs, and alternates TRACED0, LPTIM1_OUT, I2C4_SDA, SPI2_MOSI, LPUART1_TX and SAI1_SD_A.
10 PC2 bidirectional 5 V-tolerant GPIO with LCD and analog-switch options, ADC123_INP3/ADC123_INN2 analog inputs, and alternates LPTIM1_IN2, SPI2_MISO, DFSDM1_CKOUT and LCD_SEG20.
11 PC3 bidirectional 5 V-tolerant GPIO with LCD and analog-switch options, ADC123_INP4/ADC123_INN3 analog inputs, and alternates LPTIM1_ETR, SPI2_MOSI, LCD_VLCD, SAI1_SD_A and LPTIM2_ETR.
12 VSSA/VREF- power_in Analog ground and negative ADC reference VREF-; VREF- can be internally connected to VSSA depending on the package.
13 VDDA/VREF+ power_in Analog supply (1.62 V to 3.6 V when ADC or COMP is used) and positive ADC reference VREF+, which may exceed VDDA by no more than 0.4 V.
14 PA0 bidirectional 5 V-tolerant GPIO with analog-switch (VDDA) option, OPAMP1_VINPP and ADC12_INP5/ADC12_INN4 analog inputs, and alternates TIM2_CH1, TIM8_ETR, USART2_CTS, UART4_TX and RTC_TAMP2/WKUP1.
15 PA1 bidirectional 5 V-tolerant GPIO with LCD and analog-switch options, OPAMP1_VINPM and ADC12_INP6/ADC12_INN5 analog inputs, and alternates TIM2_CH2, I2C1_SMBA, SPI1_SCK, USART2_RTS_DE and UART4_RX.
16 PA2 bidirectional 5 V-tolerant GPIO with LCD and analog-switch options, ADC12_INP7/ADC12_INN6 analog inputs and WKUP4/LSCO, and alternates TIM2_CH3, USART2_TX, LPUART1_TX, QUADSPI_BK1_NCS and LCD_SEG1.
17 PA3 bidirectional 3.6 V-tolerant GPIO (TT) with analog-switch option, OPAMP1_VOUT and ADC12_INP8/ADC12_INN7 analog functions, and alternates TIM2_CH4, USART2_RX, LPUART1_RX, QUADSPI_CLK and SAI1_MCLK_A.
18 VSS power_in Ground pin.
19 VDD power_in Main power supply, 1.71 V to 3.6 V (Table 22).
20 PA4 bidirectional 3.6 V-tolerant GPIO with analog-switch (VDDA) option, ADC12_INP9/ADC12_INN8 and DAC1_OUT1 analog functions, and alternates SPI1_NSS, SPI3_NSS, USART2_CK, DCMI_HSYNC, SAI1_FS_B and LPTIM2_OUT.
21 PA5 bidirectional 3.6 V-tolerant GPIO with analog-switch (VDDA) option, ADC12_INP10/ADC12_INN9 and DAC1_OUT2 analog functions, and alternates TIM2_CH1, TIM2_ETR, TIM8_CH1N, SPI1_SCK and LPTIM2_ETR.
22 PA6 bidirectional 5 V-tolerant GPIO with LCD and analog-switch options, OPAMP2_VINPP and ADC12_INP11/ADC12_INN10 analog inputs, and alternates TIM1_BKIN, TIM3_CH1, TIM8_BKIN, DCMI_PIXCLK, SPI1_MISO, USART3_CTS and LPUART1_CTS.
23 PA7 bidirectional 5 V-tolerant GPIO with Fm+, LCD and analog-switch options, OPAMP2_VINPM and ADC12_INP12/ADC12_INN11 analog inputs, and alternates TIM1_CH1N, TIM3_CH2, TIM8_CH1N, I2C3_SCL, SPI1_MOSI and QUADSPI_BK1_IO2.
24 PC4 bidirectional 5 V-tolerant GPIO with LCD and analog-switch options, COMP1_INPM and ADC12_INP13/ADC12_INN12 analog inputs, and alternates USART3_TX, QUADSPI_BK2_IO3 and LCD_SEG22.
25 PC5 bidirectional 5 V-tolerant GPIO with analog-switch option, COMP1_INPP, ADC12_INP14/ADC12_INN13 and WKUP5 analog/wakeup functions, and alternates USART3_RX and LCD_SEG23.
26 PB0 bidirectional 3.6 V-tolerant GPIO (TT) with analog-switch option, OPAMP2_VOUT and ADC12_INP15/ADC12_INN14 analog functions, and alternates TIM1_CH2N, TIM3_CH3, TIM8_CH2N, SPI1_NSS, USART3_CK, QUADSPI_BK1_IO1, COMP1_OUT and SAI1_EXTCLK.
27 PB1 bidirectional 5 V-tolerant GPIO with LCD and analog-switch options, COMP1_INPM and ADC12_INP16/ADC12_INN15 analog inputs, and alternates TIM1_CH3N, TIM3_CH4, TIM8_CH3N, DFSDM1_DATIN0, USART3_RTS_DE, LPUART1_RTS_DE and LPTIM2_IN1.
28 PB2 bidirectional 5 V-tolerant GPIO with LCD and analog-switch options, COMP1_INP analog input, and alternates RTC_OUT, LPTIM1_OUT, I2C3_SMBA, DFSDM1_CKIN0 and LCD_VLCD.
29 PB10 bidirectional 5 V-tolerant GPIO with Fm+ and LCD options, and alternates TIM2_CH3, I2C4_SCL, I2C2_SCL, SPI2_SCK, DFSDM1_DATIN7, USART3_TX, LPUART1_RX, TSC_SYNC, QUADSPI_CLK and COMP1_OUT.
30 PB11 bidirectional 5 V-tolerant GPIO with Fm+ and LCD options, and alternates TIM2_CH4, I2C4_SDA, I2C2_SDA, DFSDM1_CKIN7, USART3_RX, LPUART1_TX, QUADSPI_BK1_NCS and COMP2_OUT.
31 VSS power_in Ground pin.
32 VDD power_in Main power supply, 1.71 V to 3.6 V (Table 22).
33 PB12 bidirectional 5 V-tolerant GPIO with LCD option, and alternates TIM1_BKIN, TIM1_BKIN_COMP2, I2C2_SMBA, SPI2_NSS, DFSDM1_DATIN1, USART3_CK, LPUART1_RTS_DE, TSC_G1_IO1, CAN2_RX, LCD_SEG12 and SAI2_FS_A.
34 PB13 bidirectional 5 V-tolerant GPIO with Fm+ and LCD options, and alternates TIM1_CH1N, I2C2_SCL, SPI2_SCK, DFSDM1_CKIN1, USART3_CTS, LPUART1_CTS, TSC_G1_IO2, CAN2_TX, LCD_SEG13 and SAI2_SCK_A.
35 PB14 bidirectional 5 V-tolerant GPIO with Fm+ and LCD options, and alternates TIM1_CH2N, TIM8_CH2N, I2C2_SDA, SPI2_MISO, DFSDM1_DATIN2, USART3_RTS_DE, TSC_G1_IO3, LCD_SEG14 and TIM15_CH1.
36 PB15 bidirectional 5 V-tolerant GPIO with LCD option, RTC_REFIN input, and alternates TIM1_CH3N, TIM8_CH3N, SPI2_MOSI, DFSDM1_CKIN2, TSC_G1_IO4, LCD_SEG15, SAI2_SD_A and TIM15_CH2.
37 PC6 bidirectional 5 V-tolerant GPIO with LCD option, and alternates TIM3_CH1, TIM8_CH1, DFSDM1_CKIN3, TSC_G4_IO1, DCMI_D0, LCD_SEG24, SDMMC1_D6 and SAI2_MCLK_A.
38 PC7 bidirectional 5 V-tolerant GPIO with LCD option, and alternates TIM3_CH2, TIM8_CH2, DFSDM1_DATIN3, TSC_G4_IO2, DCMI_D1, LCD_SEG25, SDMMC1_D7 and SAI2_MCLK_B.
39 PC8 bidirectional 5 V-tolerant GPIO with LCD option, and alternates TIM3_CH3, TIM8_CH3, TSC_G4_IO3, DCMI_D2, LCD_SEG26 and SDMMC1_D0.
40 PC9 bidirectional 5 V-tolerant GPIO with Fm+ and LCD options, and alternates TIM8_BKIN2, TIM3_CH4, TIM8_CH4, DCMI_D3, I2C3_SDA, TSC_G4_IO4, OTG_FS_NOE, LCD_SEG27, SDMMC1_D1 and SAI2_EXTCLK.
41 PA8 bidirectional 5 V-tolerant GPIO with LCD option, and alternates MCO, TIM1_CH1, USART1_CK, OTG_FS_SOF, LCD_COM0, SWPMI1_IO, SAI1_SCK_A and LPTIM2_OUT.
42 PA9 bidirectional 5 V-tolerant GPIO with LCD and USB (VDDUSB) options, and alternates TIM1_CH2, SPI2_SCK, DCMI_D0, USART1_TX, LCD_COM1, SAI1_FS_A, TIM15_BKIN and OTG_FS_VBUS.
43 PA10 bidirectional 5 V-tolerant GPIO with LCD and USB (VDDUSB) options, and alternates TIM1_CH3, DCMI_D1, USART1_RX, OTG_FS_ID, LCD_COM2, SAI1_SD_A and TIM17_BKIN.
44 PA11 bidirectional 5 V-tolerant GPIO with USB (VDDUSB) option, and alternates TIM1_CH4, TIM1_BKIN2, SPI1_MISO, USART1_CTS, CAN1_RX, OTG_FS_DM and TIM1_BKIN2_COMP1.
45 PA12 bidirectional 5 V-tolerant GPIO with USB (VDDUSB) option, and alternates TIM1_ETR, SPI1_MOSI, USART1_RTS_DE, CAN1_TX and OTG_FS_DP.
46 PA13 (JTMS/SWDIO) bidirectional 5 V-tolerant GPIO that after reset is the JTMS/SWDIO debug pin with the internal pull-up enabled; alternates IR_OUT, OTG_FS_NOE, SWPMI1_TX and SAI1_SD_B.
47 VSS power_in Ground pin.
48 VDDUSB power_in USB supply, 3.0 V to 3.6 V when USB is used (0 to 3.6 V when USB is not used) (Table 22).
49 PA14 (JTCK/SWCLK) bidirectional 5 V-tolerant GPIO that after reset is the JTCK/SWCLK debug pin with the internal pull-down enabled; alternates LPTIM1_OUT, I2C1_SMBA, I2C4_SMBA, OTG_FS_SOF, SWPMI1_RX and SAI1_FS_B.
50 PA15 (JTDI) bidirectional 5 V-tolerant GPIO that after reset is the JTDI debug pin with the internal pull-up enabled; alternates TIM2_CH1, TIM2_ETR, USART2_RX, SPI1_NSS, SPI3_NSS, LCD_SEG17 and SAI2_FS_B.
51 PC10 bidirectional 5 V-tolerant GPIO with LCD option, and alternates TRACED1, SPI3_SCK, USART3_TX, UART4_TX, TSC_G3_IO2, DCMI_D8, SDMMC1_D2 and SAI2_SCK_B.
52 PC11 bidirectional 5 V-tolerant GPIO with LCD option, and alternates QUADSPI_BK2_NCS, SPI3_MISO, USART3_RX, UART4_RX, TSC_G3_IO3, DCMI_D4, SDMMC1_D3 and SAI2_MCLK_B.
53 PC12 bidirectional 5 V-tolerant GPIO with LCD option, and alternates TRACED3, SPI3_MOSI, USART3_CK, UART5_TX, TSC_G3_IO4, DCMI_D9, SDMMC1_CK and SAI2_SD_B.
54 PD2 bidirectional 5 V-tolerant GPIO with LCD option, and alternates TRACED2, TIM3_ETR, USART3_RTS_DE, UART5_RX, TSC_SYNC, DCMI_D11 and SDMMC1_CMD.
55 PB3 (JTDO/TRACESWO) bidirectional 5 V-tolerant GPIO with analog-switch option, COMP2_INM analog input, which after reset is the JTDO/TRACESWO debug function; alternates TIM2_CH2, SPI1_SCK, SPI3_SCK, USART1_RTS_DE and SAI1_SCK_B.
56 PB4 (NJTRST) bidirectional 5 V-tolerant GPIO with Fm+, LCD and analog-switch options, COMP2_INP analog input, which after reset is the NJTRST debug pin with the internal pull-up enabled; alternates TIM3_CH1, I2C3_SDA, SPI1_MISO, SPI3_MISO, USART1_CTS, DCMI_D12 and TIM17_BKIN.
57 PB5 bidirectional 5 V-tolerant GPIO with analog-switch option, and alternates LPTIM1_IN1, TIM3_CH2, CAN2_RX, I2C1_SMBA, SPI1_MOSI, SPI3_MOSI, USART1_CK, UART5_CTS, TSC_G2_IO2, DCMI_D10, LCD_SEG9, COMP2_OUT, SAI1_SD_B and TIM16_BKIN.
58 PB6 bidirectional 5 V-tolerant GPIO with Fm+ and analog-switch (VDDA) options, COMP2_INP analog input, and alternates LPTIM1_ETR, TIM4_CH1, TIM8_BKIN2, I2C1_SCL, I2C4_SCL, DFSDM1_DATIN5, USART1_TX, CAN2_TX, DCMI_D5 and SAI1_FS_B.
59 PB7 bidirectional 5 V-tolerant GPIO with Fm+, LCD and analog-switch options, COMP2_INM and PVD_IN analog functions, and alternates LPTIM1_IN2, TIM4_CH2, TIM8_BKIN, I2C1_SDA, I2C4_SDA, DFSDM1_CKIN5, USART1_RX, UART4_CTS, TSC_G2_IO4, DCMI_VSYNC, LCD_SEG21 and FMC_NL.
60 PH3-BOOT0 bidirectional 5 V-tolerant GPIO that is also the BOOT0 boot-mode input; the BOOT0 input is specified up to 9.0 V (Table 19 and Table 22).
61 PB8 bidirectional 5 V-tolerant GPIO with Fm+ and LCD options, and alternates TIM4_CH3, I2C1_SCL, DFSDM1_DATIN6, CAN1_RX, DCMI_D6, LCD_SEG16, SDMMC1_D4, SAI1_MCLK_A and TIM16_CH1.
62 PB9 bidirectional 5 V-tolerant GPIO with Fm+ and LCD options, and alternates IR_OUT, TIM4_CH4, I2C1_SDA, SPI2_NSS, DFSDM1_CKIN6, CAN1_TX, DCMI_D7, LCD_COM3, SDMMC1_D5, SAI1_FS_A and TIM17_CH1.
63 VSS power_in Ground pin.
64 VDD power_in Main power supply, 1.71 V to 3.6 V (Table 22).

Key specifications

Parameter Value
Manufacturer STMicroelectronics
Package LQFP-64(10x10)
Category Single Chip Microcomputer/Microcontroller
Pins 64

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Standard operating voltage (fHCLK internal AHB clock frequency) fHCLK 0 80 MHz 126
Standard operating voltage VDD 1.71 3.6 V 126
Standard operating voltage VDD12 1.08 1.32 V Full frequency range 126
Standard operating voltage VDD12 1.05 V Up to 26 MHz 126
PG[15:2] I/Os supply voltage VDDIO2 1.08 3.6 V At least one I/O in PG[15:2] used 126
PG[15:2] I/Os supply voltage VDDIO2 0 3.6 V PG[15:2] not used 126
Analog supply voltage VDDA 1.62 3.6 V ADC or COMP used 126
Analog supply voltage VDDA 1.8 V DAC or OPAMP used 126
Analog supply voltage VDDA 2.4 V VREFBUF used 126
Backup operating voltage VBAT 1.55 3.6 V 126
USB supply voltage VDDUSB 3 3.6 V USB used 126
I/O input voltage (BOOT0) VIN 0 9 V BOOT0 126
I/O input voltage (TT_xx I/O) VIN -0.3 V TT_xx I/O; max printed as VDDIOx+0.3 (formula) 126
I/O input voltage (all I/O except BOOT0 and TT_xx) VIN -0.3 V Max printed as Min(Min(VDD, VDDA, VDDIO2, VDDUSB, VLCD)+3.6 V, 5.5 V) (formula) 126
Ambient temperature for the suffix 6 version (maximum power dissipation) TA -40 85 °C Suffix 6, maximum power dissipation 127
Ambient temperature for the suffix 6 version (low-power dissipation) TA -40 105 °C Suffix 6, low-power dissipation 127
Junction temperature range (suffix 6 version) TJ -40 105 °C Suffix 6 version 127
Power dissipation at TA = 85 °C for suffix 6 (LQFP64) PD 444 mW TA = 85 °C, suffix 6, LQFP64 127
External main supply voltage (VDD, VDDA, VDDIO2, VDDUSB, VLCD, VBAT, VREF+) VDDX - VSS -0.3 4 V 124
External SMPS supply voltage VDD12 - VSS -0.3 1.4 V Range 1 124
Input voltage on FT_xxx pins VIN -0.3 V Max printed as min(VDD, VDDA, VDDIO2, VDDUSB, VLCD) + 4.0 (formula) 124
Input voltage on TT_xx pins VIN -0.3 4 V 124
Input voltage on BOOT0 pin VIN 9 V Min printed as VSS 124
Input voltage on any other pins VIN -0.3 4 V 124
Variations between different VDDX power pins of the same domain /ΔVDDx/ 50 mV 125
Variations between all the different ground pins (include VREF- pin) /VSSx-VSS/ 50 mV 125
Allowed voltage difference for VREF+ > VDDA VREF+ - VDDA 0.4 V 125
Total current into sum of all VDD power lines (source) ∑IVDD 150 mA 125
Total current out of sum of all VSS ground lines (sink) ∑IVSS 150 mA 125
Maximum current into each VDD power pin (source) IVDD(PIN) 100 mA 125
Maximum current out of each VSS ground pin (sink) IVSS(PIN) 100 mA 125
Output current sunk by any I/O and control pin except FT_f IIO(PIN) 20 mA 125
Output current sunk by any FT_f pin IIO(PIN) 20 mA 125
Output current sourced by any I/O and control pin IIO(PIN) 20 mA 125
Total output current sunk by sum of all I/Os and control pins ∑IIO(PIN) 100 mA 125
Total output current sourced by sum of all I/Os and control pins ∑IIO(PIN) 100 mA 125
Injected current on FT_xxx, TT_xx, RST and B pins, except PA4, PA5 IINJ(PIN) -5 0 mA Printed as -5/+0 125
Injected current on PA4, PA5 IINJ(PIN) -5 0 mA Printed as -5/0 125
Total injected current (sum of all I/Os and control pins) ∑/IINJ(PIN)/ 25 mA 125
Storage temperature range TSTG -65 150 °C 126
Maximum junction temperature TJ 150 °C 126
Reset temporization after BOR0 is detected tRSTTEMPO 250 400 µs VDD rising 128
Brown-out reset threshold 0 VBOR0 1.62 1.66 1.7 V Rising edge 128
Brown-out reset threshold 0 VBOR0 1.6 1.64 1.69 V Falling edge 128
Brown-out reset threshold 1 VBOR1 2.06 2.1 2.14 V Rising edge 128
Brown-out reset threshold 1 VBOR1 1.96 2 2.04 V Falling edge 128
BOR (except BOR0) and PVD consumption from VDD IDD(BOR_PVD) 1.1 1.6 µA Guaranteed by design 129
Internal reference voltage VREFINT 1.182 1.212 1.232 V -40 °C < TA < +130 °C 130
ADC sampling time when reading the internal reference voltage tS_vrefint 4 µs Guaranteed by design 130
Start time of reference voltage buffer when ADC is enabled tstart_vrefint 8 12 µs Guaranteed by design (max) 130
VREFINT buffer consumption from VDD when converted by ADC IDD(VREFINTBUF) 12.5 20 µA Guaranteed by design (max) 130
Internal reference voltage spread over the temperature range ΔVREFINT 5 7.5 mV VDD = 3 V; max guaranteed by design 130
Average temperature coefficient TCoeff 30 50 ppm/°C -40°C < TA < +130°C; max guaranteed by design 130
Long term stability ACoeff 300 1000 ppm 1000 hours, T = 25°C; max guaranteed by design 130
Average voltage coefficient VDDCoeff 250 1200 ppm/V 3.0 V < VDD < 3.6 V; max guaranteed by design 130
1/4 reference voltage VREFINT_DIV1 24 25 26 % Fraction of VREFINT 130
1/2 reference voltage VREFINT_DIV2 49 50 51 % Fraction of VREFINT 130
3/4 reference voltage VREFINT_DIV3 74 75 76 % Fraction of VREFINT 130

CAD (KiCad official)

  • Symbol: STM32L496RET6TR
  • Footprint: Package_QFP:LQFP-64_10x10mm_P0.5mm
  • 3D model: LQFP-64(10x10) (KiCad packages3D, STEP)
  • 3D model files: stm32l496ret6tr-etched.step / stm32l496ret6tr-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); stm32l496ret6tr.step / stm32l496ret6tr.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: STMicroelectronics datasheet (280 pp, sha256 07777c1c9ca126d7, retrieved 2026-11-13, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF