main
Ray
Publish 0.1.0
b969717
STM32L431KBU3
STMicroelectronics · ST Microelectronics · UFQFPN-32(5x5)
STM32L431KBU3 from STMicroelectronics, in a UFQFPN-32(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model, then checked against ST open pin data). Symbol and footprint from KiCad-official CAD; the 3D model is generated from the datasheet's package dimensions.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VDD | power_in | Main power supply pin; the standard operating voltage is 1.71 V to 3.6 V and the variation between VDD pins of the same domain must not exceed 50 mV. |
| 2 | PC14-OSC32_IN | bidirectional | FT I/O (5 V tolerant) that is supplied through the power switch and also serves as the LSE OSC32_IN; when used as a GPIO output it must not exceed 2 MHz with a 30 pF load, must not source current such as an LED, and the switch sinks only 3 mA. |
| 3 | PC15-OSC32_OUT | bidirectional | FT I/O (5 V tolerant) that is supplied through the power switch and also serves as the LSE OSC32_OUT; when used as a GPIO output it must not exceed 2 MHz with a 30 pF load, must not source current such as an LED, and the switch sinks only 3 mA. |
| 4 | NRST | bidirectional | Bidirectional reset pin with an embedded weak pull-up resistor. |
| 5 | VDDA/VREF+ | power_in | Analog supply pin: VDDA is 1.62 V to 3.6 V when the ADC or COMP is used, 1.8 V minimum when the DAC or OPAMP is used, and 2.4 V minimum when VREFBUF is used; VREF+ is internally connected to VDDA on this package. |
| 6 | PA0/CK_IN | bidirectional | FT_a I/O (5 V tolerant, analog switch supplied by VDDA) that also provides CK_IN, TIM2_CH1, USART2_CTS, COMP1_OUT, SAI1_EXTCLK, ADC1_IN5, WKUP1 and OPAMP1_VINP functions. |
| 7 | PA1 | bidirectional | FT_a I/O (5 V tolerant, analog switch supplied by VDDA) that also provides TIM2_CH2, I2C1_SMBA, SPI1_SCK, USART2_RTS_DE, TIM15_CH1N, ADC1_IN6, OPAMP1_VINM and COMP1_INP functions. |
| 8 | PA2 | bidirectional | FT_a I/O (5 V tolerant, analog switch supplied by VDDA) that also provides TIM2_CH3, USART2_TX, LPUART1_TX, QUADSPI_BK1_NCS, COMP2_OUT, TIM15_CH1, ADC1_IN7, COMP2_INM, WKUP4 and LSCO functions. |
| 9 | PA3 | bidirectional | TT_a I/O (3.6 V tolerant, analog switch supplied by VDDA) that also provides TIM2_CH4, USART2_RX, LPUART1_RX, QUADSPI_CLK, SAI1_MCLK_A, TIM15_CH2, ADC1_IN8, COMP2_INP and OPAMP1_VOUT functions. |
| 10 | PA4 | bidirectional | TT_a I/O (3.6 V tolerant, analog switch supplied by VDDA) that also provides SPI1_NSS, SPI3_NSS, USART2_CK, SAI1_FS_B, LPTIM2_OUT, ADC1_IN9, DAC1_OUT1, COMP1_INM and COMP2_INM functions. |
| 11 | PA5 | bidirectional | TT_a I/O (3.6 V tolerant, analog switch supplied by VDDA) that also provides TIM2_CH1, TIM2_ETR, SPI1_SCK, LPTIM2_ETR, ADC1_IN10, DAC1_OUT2, COMP1_INM and COMP2_INM functions. |
| 12 | PA6 | bidirectional | FT_a I/O (5 V tolerant, analog switch supplied by VDDA) that also provides TIM1_BKIN, SPI1_MISO, COMP1_OUT, USART3_CTS, LPUART1_CTS, QUADSPI_BK1_IO3, TIM1_BKIN_COMP2, TIM16_CH1 and ADC1_IN11 functions. |
| 13 | PA7 | bidirectional | FT_fa I/O (5 V tolerant, Fm+ capable, analog switch supplied by VDDA) that also provides TIM1_CH1N, I2C3_SCL, SPI1_MOSI, QUADSPI_BK1_IO2, COMP2_OUT and ADC1_IN12 functions. |
| 14 | PB0 | bidirectional | FT_a I/O (5 V tolerant, analog switch supplied by VDDA) that also provides TIM1_CH2N, SPI1_NSS, USART3_CK, QUADSPI_BK1_IO1, COMP1_OUT, SAI1_EXTCLK and ADC1_IN15 functions. |
| 15 | PB1 | bidirectional | FT_a I/O (5 V tolerant, analog switch supplied by VDDA) that also provides TIM1_CH3N, USART3_RTS_DE, LPUART1_RTS_DE, QUADSPI_BK1_IO0, LPTIM2_IN1, COMP1_INM and ADC1_IN16 functions. |
| 16 | VSS | power_in | Ground pin; the variation between all ground pins must not exceed 50 mV. |
| 17 | VDD | power_in | Main power supply pin; the standard operating voltage is 1.71 V to 3.6 V and the variation between VDD pins of the same domain must not exceed 50 mV. |
| 18 | PA8 | bidirectional | FT I/O (5 V tolerant) that also provides MCO, TIM1_CH1, USART1_CK, SWPMI1_IO, SAI1_SCK_A and LPTIM2_OUT functions. |
| 19 | PA9 | bidirectional | FT_f I/O (5 V tolerant, Fm+ capable) that also provides TIM1_CH2, I2C1_SCL, USART1_TX, SAI1_FS_A and TIM15_BKIN functions. |
| 20 | PA10 | bidirectional | FT_f I/O (5 V tolerant, Fm+ capable) that also provides TIM1_CH3, I2C1_SDA, USART1_RX and SAI1_SD_A functions. |
| 21 | PA11 | bidirectional | FT I/O (5 V tolerant) that also provides TIM1_CH4, TIM1_BKIN2, SPI1_MISO, COMP1_OUT, USART1_CTS, CAN1_RX and TIM1_BKIN2_COMP1 functions. |
| 22 | PA12 | bidirectional | FT I/O (5 V tolerant) that also provides TIM1_ETR, SPI1_MOSI, USART1_RTS_DE and CAN1_TX functions. |
| 23 | PA13 | bidirectional | FT I/O (5 V tolerant) that is configured as the JTMS-SWDIO debug function after reset with its internal pull-up enabled, and also provides IR_OUT, SWPMI1_TX and SAI1_SD_B functions. |
| 24 | PA14 | bidirectional | FT I/O (5 V tolerant) that is configured as the JTCK-SWCLK debug function after reset with its internal pull-down enabled, and also provides LPTIM1_OUT, I2C1_SMBA, SWPMI1_RX and SAI1_FS_B functions. |
| 25 | PA15 | bidirectional | FT I/O (5 V tolerant) that is configured as the JTDI debug function after reset with its internal pull-up enabled, and also provides TIM2_CH1, TIM2_ETR, USART2_RX, SPI1_NSS, SPI3_NSS, USART3_RTS_DE, TSC_G3_IO1 and SWPMI1_SUSPEND functions. |
| 26 | PB3 | bidirectional | FT_a I/O (5 V tolerant, analog switch supplied by VDDA) that is configured as the JTDO-TRACESWO debug function after reset and also provides TIM2_CH2, SPI1_SCK, SPI3_SCK, USART1_RTS_DE, SAI1_SCK_B and COMP2_INM functions. |
| 27 | PB4 | bidirectional | FT_fa I/O (5 V tolerant, Fm+ capable, analog switch supplied by VDDA) that is configured as the NJTRST debug function with its internal pull-up enabled after reset, and also provides I2C3_SDA, SPI1_MISO, SPI3_MISO, USART1_CTS, TSC_G2_IO1, SAI1_MCLK_B and COMP2_INP functions. |
| 28 | PB5 | bidirectional | FT I/O (5 V tolerant) that also provides LPTIM1_IN1, I2C1_SMBA, SPI1_MOSI, SPI3_MOSI, USART1_CK, TSC_G2_IO2, COMP2_OUT, SAI1_SD_B and TIM16_BKIN functions. |
| 29 | PB6 | bidirectional | FT_fa I/O (5 V tolerant, Fm+ capable, analog switch supplied by VDDA) that also provides LPTIM1_ETR, I2C1_SCL, USART1_TX, TSC_G2_IO3, SAI1_FS_B, TIM16_CH1N and COMP2_INP functions. |
| 30 | PB7 | bidirectional | FT_fa I/O (5 V tolerant, Fm+ capable, analog switch supplied by VDDA) that also provides LPTIM1_IN2, I2C1_SDA, USART1_RX, TSC_G2_IO4, COMP2_INM and PVD_IN functions. |
| 31 | PH3/BOOT0 | bidirectional | FT I/O (5 V tolerant) that also provides the BOOT0 boot-mode function and EVENTOUT. |
| 32 | VSS | power_in | Ground pin; the variation between all ground pins must not exceed 50 mV. |
| 33 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | UFQFPN-32(5x5) |
| Category | Embedded Processors & Controllers |
| Pins | 33 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| External main supply voltage (VDD, VDDA, VBAT) vs VSS | VDDX - VSS | -0.3 | 4 | V | 86 | ||
| Input voltage on TT_xx pins | VIN | 4 | V | Minimum printed as VSS-0.3 (formula, not converted) | 86 | ||
| Input voltage on any other pins | VIN | 4 | V | Minimum printed as VSS-0.3 (formula, not converted) | 86 | ||
| Variations between different VDDX power pins of the same domain | /ΔVDDx/ | 50 | mV | 86 | |||
| Variations between all the different ground pins | /VSSx-VSS/ | 50 | mV | Include VREF- pin | 86 | ||
| Total current into sum of all VDD power lines (source) | ∑IVDD | 140 | mA | 87 | |||
| Total current out of sum of all VSS ground lines (sink) | ∑IVSS | 140 | mA | 87 | |||
| Maximum current into each VDD power pin (source) | IVDD(PIN) | 100 | mA | 87 | |||
| Maximum current out of each VSS ground pin (sink) | IVSS(PIN) | 100 | mA | 87 | |||
| Output current sunk by any I/O and control pin except FT_f | IIO(PIN) | 20 | mA | 87 | |||
| Output current sunk by any FT_f pin | IIO(PIN) | 20 | mA | 87 | |||
| Output current sourced by any I/O and control pin | IIO(PIN) | 20 | mA | 87 | |||
| Total output current sunk by sum of all I/Os and control pins | ∑IIO(PIN) | 100 | mA | 87 | |||
| Total output current sourced by sum of all I/Os and control pins | ∑IIO(PIN) | 100 | mA | 87 | |||
| Injected current on FT_xxx, TT_xx, RST and B pins | IINJ(PIN) | -5 | 0 | mA | except PA4, PA5 | 87 | |
| Injected current on PA4, PA5 | IINJ(PIN) | -5 | 0 | mA | 87 | ||
| Total injected current (sum of all I/Os and control pins) | ∑/IINJ(PIN)/ | 25 | mA | 87 | |||
| Storage temperature range | TSTG | -65 | 150 | °C | 87 | ||
| Maximum junction temperature | TJ | 150 | °C | 87 | |||
| Internal AHB clock frequency | fHCLK | 0 | 80 | MHz | 88 | ||
| Internal APB1 clock frequency | fPCLK1 | 0 | 80 | MHz | 88 | ||
| Internal APB2 clock frequency | fPCLK2 | 0 | 80 | MHz | 88 | ||
| Standard operating voltage | VDD | 1.71 | 3.6 | V | 88 | ||
| Analog supply voltage | VDDA | 1.62 | 3.6 | V | ADC or COMP used | 88 | |
| Analog supply voltage | VDDA | 1.8 | 3.6 | V | DAC or OPAMP used | 88 | |
| Analog supply voltage | VDDA | 2.4 | 3.6 | V | VREFBUF used | 88 | |
| Analog supply voltage | VDDA | 0 | V | ADC, DAC, OPAMP, COMP, VREFBUF not used | 88 | ||
| Backup operating voltage | VBAT | 1.55 | 3.6 | V | 88 | ||
| I/O input voltage (TT_xx I/O) | VIN | -0.3 | V | TT_xx I/O; maximum printed as VDDIOx+0.3 (formula, not converted) | 88 | ||
| I/O input voltage (all I/O except TT_xx) | VIN | -0.3 | V | maximum printed as Min(Min(VDD,VDDA)+3.6 V, 5.5 V) (formula, not converted) | 88 | ||
| Ambient temperature, maximum power dissipation (suffix 3 version) | TA | -40 | 125 | °C | Suffix 3 version | 88 | |
| Ambient temperature, low-power dissipation (suffix 3 version) | TA | -40 | 130 | °C | Suffix 3 version, low-power dissipation | 88 | |
| Junction temperature range (suffix 3 version) | TJ | -40 | 130 | °C | Suffix 3 version | 88 | |
| VDD rise time rate | tVDD | 0 | µs/V | maximum printed as ∞ | 89 | ||
| VDD fall time rate | tVDD | 10 | µs/V | maximum printed as ∞ | 89 | ||
| VDDA rise time rate | tVDDA | 0 | µs/V | maximum printed as ∞ | 89 | ||
| VDDA fall time rate | tVDDA | 10 | µs/V | maximum printed as ∞ | 89 | ||
| Reset temporization after BOR0 is detected | tRSTTEMPO | 250 | 400 | µs | VDD rising | 89 | |
| Brown-out reset threshold 0 | VBOR0 | 1.62 | 1.66 | 1.7 | V | Rising edge | 89 |
| Brown-out reset threshold 0 | VBOR0 | 1.6 | 1.64 | 1.69 | V | Falling edge | 89 |
| Internal reference voltage | VREFINT | 1.182 | 1.212 | 1.232 | V | -40 °C < TA < +130 °C | 91 |
| ADC sampling time when reading the internal reference voltage | tS_vrefint | 4 | µs | 91 | |||
| Start time of reference voltage buffer when ADC is enabled | tstart_vrefint | 8 | 12 | µs | 91 | ||
| VREFINT buffer consumption from VDD when converted by ADC | IDD(VREFINTBUF) | 12.5 | 20 | µA | 91 | ||
| Internal reference voltage spread over the temperature range | ΔVREFINT | 5 | 7.5 | mV | VDD = 3 V | 91 | |
| Temperature coefficient | TCoeff | 30 | 50 | ppm/°C | -40°C < TA < +130°C | 91 | |
| Long term stability | ACoeff | 300 | 1000 | ppm | 1000 hours, T = 25°C | 91 | |
| Voltage coefficient | VDDCoeff | 250 | 1200 | ppm/V | 3.0 V < VDD < 3.6 V | 91 | |
| 1/4 reference voltage | VREFINT_DIV1 | 24 | 25 | 26 | % VREFINT | 91 | |
| 1/2 reference voltage | VREFINT_DIV2 | 49 | 50 | 51 | % VREFINT | 91 | |
| 3/4 reference voltage | VREFINT_DIV3 | 74 | 75 | 76 | % VREFINT | 91 | |
| Supply current in Run mode (Range 1) | IDD_ALL (Run) | 8.53 | 9.5 | mA | Range 1, fHCLK = 80 MHz, all peripherals disabled, TA = 25 °C, ART enabled | 94 | |
| Supply current in Run mode (Range 1) | IDD_ALL (Run) | 8.92 | 10.3 | mA | Range 1, fHCLK = 80 MHz, all peripherals disabled, TA = 125 °C, ART enabled | 94 | |
| Supply current in Low-power run mode | IDD_ALL (LPRun) | 506 | 815.9 | µA | fHCLK = fMSI = 2 MHz, all peripherals disabled, TA = 125 °C, ART enabled | 94 | |
| Supply current in Sleep mode (Range 1) | IDD_ALL (Sleep) | 2.23 | 2.5 | mA | Range 1, fHCLK = 80 MHz, all peripherals disabled, TA = 25 °C, Flash ON | 99 | |
| Supply current in Stop 2 mode, RTC disabled | IDD_ALL (Stop 2) | 1.06 | 2.1 | µA | VDD = 3 V, TA = 25 °C | 100 | |
| Supply current in Standby mode, RTC disabled, no independent watchdog | IDD_ALL (Standby) | 8836 | 30758 | nA | VDD = 3.6 V, TA = 125 °C | 104 | |
| Backup domain supply current, RTC disabled | IDD_VBAT (VBAT) | 5 | 12.5 | nA | VBAT = 3 V, TA = 25 °C | 107 | |
| Wake up time from Stop 2 mode to Run mode in Flash (Range 1) | tWUSTOP2 | 8.02 | 9.24 | µs | Wakeup clock MSI = 48 MHz | 113 | |
| Wakeup time from Shutdown mode to Run mode (Range 1) | tWUSHDN | 261.5 | 315.7 | µs | Wakeup clock MSI = 4 MHz | 113 |
CAD (land: KiCad; 3D: generated from the datasheet)
- Symbol:
STM32L431KBU3 - Footprint:
Package_DFN_QFN:UFQFPN-32-1EP_5x5mm_P0.5mm_EP3.5x3.5mm - 3D model: UFQFPN-32(5x5), generated on the KiCad land (body 5 x 5 mm, terminals on the pads, 0.55 mm tall, datasheet A, nominal). KiCad's stock model for this land is taller than the datasheet allows, so the model is generated from the datasheet drawing; the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
- 3D model files:
stm32l431kbu3-etched.step/stm32l431kbu3-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);stm32l431kbu3.step/stm32l431kbu3.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: STMicroelectronics datasheet (208 pp, sha256
71963de3cb899f8f, retrieved 2026-11-13, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: land: KiCad official libraries (CC-BY-SA 4.0); 3D: generated from the datasheet's package dimensions (provenance.model_3d_generated).
# STM32L431KBU3
**STMicroelectronics** · ST Microelectronics · UFQFPN-32(5x5)
STM32L431KBU3 from STMicroelectronics, in a UFQFPN-32(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model, then checked against ST open pin data). Symbol and footprint from KiCad-official CAD; the 3D model is generated from the datasheet's package dimensions.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VDD | power_in | Main power supply pin; the standard operating voltage is 1.71 V to 3.6 V and the variation between VDD pins of the same domain must not exceed 50 mV. |
| 2 | PC14-OSC32_IN | bidirectional | FT I/O (5 V tolerant) that is supplied through the power switch and also serves as the LSE OSC32_IN; when used as a GPIO output it must not exceed 2 MHz with a 30 pF load, must not source current such as an LED, and the switch sinks only 3 mA. |
| 3 | PC15-OSC32_OUT | bidirectional | FT I/O (5 V tolerant) that is supplied through the power switch and also serves as the LSE OSC32_OUT; when used as a GPIO output it must not exceed 2 MHz with a 30 pF load, must not source current such as an LED, and the switch sinks only 3 mA. |
| 4 | NRST | bidirectional | Bidirectional reset pin with an embedded weak pull-up resistor. |
| 5 | VDDA/VREF+ | power_in | Analog supply pin: VDDA is 1.62 V to 3.6 V when the ADC or COMP is used, 1.8 V minimum when the DAC or OPAMP is used, and 2.4 V minimum when VREFBUF is used; VREF+ is internally connected to VDDA on this package. |
| 6 | PA0/CK_IN | bidirectional | FT_a I/O (5 V tolerant, analog switch supplied by VDDA) that also provides CK_IN, TIM2_CH1, USART2_CTS, COMP1_OUT, SAI1_EXTCLK, ADC1_IN5, WKUP1 and OPAMP1_VINP functions. |
| 7 | PA1 | bidirectional | FT_a I/O (5 V tolerant, analog switch supplied by VDDA) that also provides TIM2_CH2, I2C1_SMBA, SPI1_SCK, USART2_RTS_DE, TIM15_CH1N, ADC1_IN6, OPAMP1_VINM and COMP1_INP functions. |
| 8 | PA2 | bidirectional | FT_a I/O (5 V tolerant, analog switch supplied by VDDA) that also provides TIM2_CH3, USART2_TX, LPUART1_TX, QUADSPI_BK1_NCS, COMP2_OUT, TIM15_CH1, ADC1_IN7, COMP2_INM, WKUP4 and LSCO functions. |
| 9 | PA3 | bidirectional | TT_a I/O (3.6 V tolerant, analog switch supplied by VDDA) that also provides TIM2_CH4, USART2_RX, LPUART1_RX, QUADSPI_CLK, SAI1_MCLK_A, TIM15_CH2, ADC1_IN8, COMP2_INP and OPAMP1_VOUT functions. |
| 10 | PA4 | bidirectional | TT_a I/O (3.6 V tolerant, analog switch supplied by VDDA) that also provides SPI1_NSS, SPI3_NSS, USART2_CK, SAI1_FS_B, LPTIM2_OUT, ADC1_IN9, DAC1_OUT1, COMP1_INM and COMP2_INM functions. |
| 11 | PA5 | bidirectional | TT_a I/O (3.6 V tolerant, analog switch supplied by VDDA) that also provides TIM2_CH1, TIM2_ETR, SPI1_SCK, LPTIM2_ETR, ADC1_IN10, DAC1_OUT2, COMP1_INM and COMP2_INM functions. |
| 12 | PA6 | bidirectional | FT_a I/O (5 V tolerant, analog switch supplied by VDDA) that also provides TIM1_BKIN, SPI1_MISO, COMP1_OUT, USART3_CTS, LPUART1_CTS, QUADSPI_BK1_IO3, TIM1_BKIN_COMP2, TIM16_CH1 and ADC1_IN11 functions. |
| 13 | PA7 | bidirectional | FT_fa I/O (5 V tolerant, Fm+ capable, analog switch supplied by VDDA) that also provides TIM1_CH1N, I2C3_SCL, SPI1_MOSI, QUADSPI_BK1_IO2, COMP2_OUT and ADC1_IN12 functions. |
| 14 | PB0 | bidirectional | FT_a I/O (5 V tolerant, analog switch supplied by VDDA) that also provides TIM1_CH2N, SPI1_NSS, USART3_CK, QUADSPI_BK1_IO1, COMP1_OUT, SAI1_EXTCLK and ADC1_IN15 functions. |
| 15 | PB1 | bidirectional | FT_a I/O (5 V tolerant, analog switch supplied by VDDA) that also provides TIM1_CH3N, USART3_RTS_DE, LPUART1_RTS_DE, QUADSPI_BK1_IO0, LPTIM2_IN1, COMP1_INM and ADC1_IN16 functions. |
| 16 | VSS | power_in | Ground pin; the variation between all ground pins must not exceed 50 mV. |
| 17 | VDD | power_in | Main power supply pin; the standard operating voltage is 1.71 V to 3.6 V and the variation between VDD pins of the same domain must not exceed 50 mV. |
| 18 | PA8 | bidirectional | FT I/O (5 V tolerant) that also provides MCO, TIM1_CH1, USART1_CK, SWPMI1_IO, SAI1_SCK_A and LPTIM2_OUT functions. |
| 19 | PA9 | bidirectional | FT_f I/O (5 V tolerant, Fm+ capable) that also provides TIM1_CH2, I2C1_SCL, USART1_TX, SAI1_FS_A and TIM15_BKIN functions. |
| 20 | PA10 | bidirectional | FT_f I/O (5 V tolerant, Fm+ capable) that also provides TIM1_CH3, I2C1_SDA, USART1_RX and SAI1_SD_A functions. |
| 21 | PA11 | bidirectional | FT I/O (5 V tolerant) that also provides TIM1_CH4, TIM1_BKIN2, SPI1_MISO, COMP1_OUT, USART1_CTS, CAN1_RX and TIM1_BKIN2_COMP1 functions. |
| 22 | PA12 | bidirectional | FT I/O (5 V tolerant) that also provides TIM1_ETR, SPI1_MOSI, USART1_RTS_DE and CAN1_TX functions. |
| 23 | PA13 | bidirectional | FT I/O (5 V tolerant) that is configured as the JTMS-SWDIO debug function after reset with its internal pull-up enabled, and also provides IR_OUT, SWPMI1_TX and SAI1_SD_B functions. |
| 24 | PA14 | bidirectional | FT I/O (5 V tolerant) that is configured as the JTCK-SWCLK debug function after reset with its internal pull-down enabled, and also provides LPTIM1_OUT, I2C1_SMBA, SWPMI1_RX and SAI1_FS_B functions. |
| 25 | PA15 | bidirectional | FT I/O (5 V tolerant) that is configured as the JTDI debug function after reset with its internal pull-up enabled, and also provides TIM2_CH1, TIM2_ETR, USART2_RX, SPI1_NSS, SPI3_NSS, USART3_RTS_DE, TSC_G3_IO1 and SWPMI1_SUSPEND functions. |
| 26 | PB3 | bidirectional | FT_a I/O (5 V tolerant, analog switch supplied by VDDA) that is configured as the JTDO-TRACESWO debug function after reset and also provides TIM2_CH2, SPI1_SCK, SPI3_SCK, USART1_RTS_DE, SAI1_SCK_B and COMP2_INM functions. |
| 27 | PB4 | bidirectional | FT_fa I/O (5 V tolerant, Fm+ capable, analog switch supplied by VDDA) that is configured as the NJTRST debug function with its internal pull-up enabled after reset, and also provides I2C3_SDA, SPI1_MISO, SPI3_MISO, USART1_CTS, TSC_G2_IO1, SAI1_MCLK_B and COMP2_INP functions. |
| 28 | PB5 | bidirectional | FT I/O (5 V tolerant) that also provides LPTIM1_IN1, I2C1_SMBA, SPI1_MOSI, SPI3_MOSI, USART1_CK, TSC_G2_IO2, COMP2_OUT, SAI1_SD_B and TIM16_BKIN functions. |
| 29 | PB6 | bidirectional | FT_fa I/O (5 V tolerant, Fm+ capable, analog switch supplied by VDDA) that also provides LPTIM1_ETR, I2C1_SCL, USART1_TX, TSC_G2_IO3, SAI1_FS_B, TIM16_CH1N and COMP2_INP functions. |
| 30 | PB7 | bidirectional | FT_fa I/O (5 V tolerant, Fm+ capable, analog switch supplied by VDDA) that also provides LPTIM1_IN2, I2C1_SDA, USART1_RX, TSC_G2_IO4, COMP2_INM and PVD_IN functions. |
| 31 | PH3/BOOT0 | bidirectional | FT I/O (5 V tolerant) that also provides the BOOT0 boot-mode function and EVENTOUT. |
| 32 | VSS | power_in | Ground pin; the variation between all ground pins must not exceed 50 mV. |
| 33 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | UFQFPN-32(5x5) |
| Category | Embedded Processors & Controllers |
| Pins | 33 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| External main supply voltage (VDD, VDDA, VBAT) vs VSS | VDDX - VSS | -0.3 | | 4 | V | | 86 |
| Input voltage on TT_xx pins | VIN | | | 4 | V | Minimum printed as VSS-0.3 (formula, not converted) | 86 |
| Input voltage on any other pins | VIN | | | 4 | V | Minimum printed as VSS-0.3 (formula, not converted) | 86 |
| Variations between different VDDX power pins of the same domain | /ΔVDDx/ | | | 50 | mV | | 86 |
| Variations between all the different ground pins | /VSSx-VSS/ | | | 50 | mV | Include VREF- pin | 86 |
| Total current into sum of all VDD power lines (source) | ∑IVDD | | | 140 | mA | | 87 |
| Total current out of sum of all VSS ground lines (sink) | ∑IVSS | | | 140 | mA | | 87 |
| Maximum current into each VDD power pin (source) | IVDD(PIN) | | | 100 | mA | | 87 |
| Maximum current out of each VSS ground pin (sink) | IVSS(PIN) | | | 100 | mA | | 87 |
| Output current sunk by any I/O and control pin except FT_f | IIO(PIN) | | | 20 | mA | | 87 |
| Output current sunk by any FT_f pin | IIO(PIN) | | | 20 | mA | | 87 |
| Output current sourced by any I/O and control pin | IIO(PIN) | | | 20 | mA | | 87 |
| Total output current sunk by sum of all I/Os and control pins | ∑IIO(PIN) | | | 100 | mA | | 87 |
| Total output current sourced by sum of all I/Os and control pins | ∑IIO(PIN) | | | 100 | mA | | 87 |
| Injected current on FT_xxx, TT_xx, RST and B pins | IINJ(PIN) | -5 | | 0 | mA | except PA4, PA5 | 87 |
| Injected current on PA4, PA5 | IINJ(PIN) | -5 | | 0 | mA | | 87 |
| Total injected current (sum of all I/Os and control pins) | ∑/IINJ(PIN)/ | | | 25 | mA | | 87 |
| Storage temperature range | TSTG | -65 | | 150 | °C | | 87 |
| Maximum junction temperature | TJ | | | 150 | °C | | 87 |
| Internal AHB clock frequency | fHCLK | 0 | | 80 | MHz | | 88 |
| Internal APB1 clock frequency | fPCLK1 | 0 | | 80 | MHz | | 88 |
| Internal APB2 clock frequency | fPCLK2 | 0 | | 80 | MHz | | 88 |
| Standard operating voltage | VDD | 1.71 | | 3.6 | V | | 88 |
| Analog supply voltage | VDDA | 1.62 | | 3.6 | V | ADC or COMP used | 88 |
| Analog supply voltage | VDDA | 1.8 | | 3.6 | V | DAC or OPAMP used | 88 |
| Analog supply voltage | VDDA | 2.4 | | 3.6 | V | VREFBUF used | 88 |
| Analog supply voltage | VDDA | 0 | | | V | ADC, DAC, OPAMP, COMP, VREFBUF not used | 88 |
| Backup operating voltage | VBAT | 1.55 | | 3.6 | V | | 88 |
| I/O input voltage (TT_xx I/O) | VIN | -0.3 | | | V | TT_xx I/O; maximum printed as VDDIOx+0.3 (formula, not converted) | 88 |
| I/O input voltage (all I/O except TT_xx) | VIN | -0.3 | | | V | maximum printed as Min(Min(VDD,VDDA)+3.6 V, 5.5 V) (formula, not converted) | 88 |
| Ambient temperature, maximum power dissipation (suffix 3 version) | TA | -40 | | 125 | °C | Suffix 3 version | 88 |
| Ambient temperature, low-power dissipation (suffix 3 version) | TA | -40 | | 130 | °C | Suffix 3 version, low-power dissipation | 88 |
| Junction temperature range (suffix 3 version) | TJ | -40 | | 130 | °C | Suffix 3 version | 88 |
| VDD rise time rate | tVDD | 0 | | | µs/V | maximum printed as ∞ | 89 |
| VDD fall time rate | tVDD | 10 | | | µs/V | maximum printed as ∞ | 89 |
| VDDA rise time rate | tVDDA | 0 | | | µs/V | maximum printed as ∞ | 89 |
| VDDA fall time rate | tVDDA | 10 | | | µs/V | maximum printed as ∞ | 89 |
| Reset temporization after BOR0 is detected | tRSTTEMPO | | 250 | 400 | µs | VDD rising | 89 |
| Brown-out reset threshold 0 | VBOR0 | 1.62 | 1.66 | 1.7 | V | Rising edge | 89 |
| Brown-out reset threshold 0 | VBOR0 | 1.6 | 1.64 | 1.69 | V | Falling edge | 89 |
| Internal reference voltage | VREFINT | 1.182 | 1.212 | 1.232 | V | -40 °C < TA < +130 °C | 91 |
| ADC sampling time when reading the internal reference voltage | tS_vrefint | 4 | | | µs | | 91 |
| Start time of reference voltage buffer when ADC is enabled | tstart_vrefint | | 8 | 12 | µs | | 91 |
| VREFINT buffer consumption from VDD when converted by ADC | IDD(VREFINTBUF) | | 12.5 | 20 | µA | | 91 |
| Internal reference voltage spread over the temperature range | ΔVREFINT | | 5 | 7.5 | mV | VDD = 3 V | 91 |
| Temperature coefficient | TCoeff | | 30 | 50 | ppm/°C | -40°C < TA < +130°C | 91 |
| Long term stability | ACoeff | | 300 | 1000 | ppm | 1000 hours, T = 25°C | 91 |
| Voltage coefficient | VDDCoeff | | 250 | 1200 | ppm/V | 3.0 V < VDD < 3.6 V | 91 |
| 1/4 reference voltage | VREFINT_DIV1 | 24 | 25 | 26 | % VREFINT | | 91 |
| 1/2 reference voltage | VREFINT_DIV2 | 49 | 50 | 51 | % VREFINT | | 91 |
| 3/4 reference voltage | VREFINT_DIV3 | 74 | 75 | 76 | % VREFINT | | 91 |
| Supply current in Run mode (Range 1) | IDD_ALL (Run) | | 8.53 | 9.5 | mA | Range 1, fHCLK = 80 MHz, all peripherals disabled, TA = 25 °C, ART enabled | 94 |
| Supply current in Run mode (Range 1) | IDD_ALL (Run) | | 8.92 | 10.3 | mA | Range 1, fHCLK = 80 MHz, all peripherals disabled, TA = 125 °C, ART enabled | 94 |
| Supply current in Low-power run mode | IDD_ALL (LPRun) | | 506 | 815.9 | µA | fHCLK = fMSI = 2 MHz, all peripherals disabled, TA = 125 °C, ART enabled | 94 |
| Supply current in Sleep mode (Range 1) | IDD_ALL (Sleep) | | 2.23 | 2.5 | mA | Range 1, fHCLK = 80 MHz, all peripherals disabled, TA = 25 °C, Flash ON | 99 |
| Supply current in Stop 2 mode, RTC disabled | IDD_ALL (Stop 2) | | 1.06 | 2.1 | µA | VDD = 3 V, TA = 25 °C | 100 |
| Supply current in Standby mode, RTC disabled, no independent watchdog | IDD_ALL (Standby) | | 8836 | 30758 | nA | VDD = 3.6 V, TA = 125 °C | 104 |
| Backup domain supply current, RTC disabled | IDD_VBAT (VBAT) | | 5 | 12.5 | nA | VBAT = 3 V, TA = 25 °C | 107 |
| Wake up time from Stop 2 mode to Run mode in Flash (Range 1) | tWUSTOP2 | | 8.02 | 9.24 | µs | Wakeup clock MSI = 48 MHz | 113 |
| Wakeup time from Shutdown mode to Run mode (Range 1) | tWUSHDN | | 261.5 | 315.7 | µs | Wakeup clock MSI = 4 MHz | 113 |
## CAD (land: KiCad; 3D: generated from the datasheet)
- Symbol: `STM32L431KBU3`
- Footprint: `Package_DFN_QFN:UFQFPN-32-1EP_5x5mm_P0.5mm_EP3.5x3.5mm`
- 3D model: UFQFPN-32(5x5), generated on the KiCad land (body 5 x 5 mm, terminals on the pads, 0.55 mm tall, datasheet A, nominal). KiCad's stock model for this land is taller than the datasheet allows, so the model is generated from the datasheet drawing; the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
- 3D model files: `stm32l431kbu3-etched.step` / `stm32l431kbu3-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `stm32l431kbu3.step` / `stm32l431kbu3.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [STMicroelectronics datasheet](https://www.st.com/content/ccc/resource/technical/document/datasheet/group3/83/b3/60/f6/b1/cc/47/7e/DM00257211/files/DM00257211.pdf/jcr:content/translations/en.DM00257211.pdf) (208 pp, sha256 `71963de3cb899f8f`, retrieved 2026-11-13, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** land: KiCad official libraries (CC-BY-SA 4.0); 3D: generated from the datasheet's package dimensions (provenance.model_3d_generated).
[Datasheet PDF](docs/stm32l431kbu3-datasheet.pdf)