← Commit history

Initial commit: component/stm32l151rct6

Ray ·53088bc34e ·
2 files changed +593
README.mdadded+100
@@ -0,0 +1,100 @@+# STM32L151RCT6++**STMicroelectronics** · Microcontrollers (MCU/MPU/SOC) · LQFP-64(10x10)++STM32L151RCT6 from STMicroelectronics, in a LQFP-64(10x10). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model, then checked against ST open pin data); symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | VLCD | power_in | LCD voltage supply; for STM32L151xC (no LCD controller) datasheet footnote 3 requires this pin be connected to VDD; max 3.6 V. |+| 2 | PC13-WKUP2 | bidirectional | 5 V tolerant GPIO PC13; additional functions: WKUP2 wakeup from Standby, RTC_TAMP1, RTC_TS, RTC_OUT; floating input after reset. |+| 3 | PC14-OSC32_IN | bidirectional | Standard 3.3 V GPIO PC14; shared with LSE 32.768 kHz oscillator input OSC32_IN when LSE is enabled (LSEON bit set); LSE has priority over GPIO. |+| 4 | PC15-OSC32_OUT | bidirectional | Standard 3.3 V GPIO PC15; shared with LSE 32.768 kHz oscillator output OSC32_OUT when LSE is enabled; LSE has priority over GPIO. |+| 5 | PH0-OSC_IN | bidirectional | Standard 3.3 V GPIO PH0; shared with HSE oscillator input OSC_IN (1-24 MHz) when HSE is enabled (HSEON bit set); HSE has priority over GPIO. |+| 6 | PH1-OSC_OUT | bidirectional | Standard 3.3 V GPIO PH1; shared with HSE oscillator output OSC_OUT when HSE is enabled; HSE has priority over GPIO. |+| 7 | NRST | bidirectional | Active-low reset; bidirectional with embedded 25-65 kΩ pull-up; filters pulses below 50 ns; VIL max = 0.3 VDD, VIH min = 0.39 VDD + 0.59 V; VOL max = 0.4 V at IOL = 2 mA. |+| 8 | PC0 | bidirectional | 5 V tolerant GPIO PC0; alternate: LCD_SEG18; additional: ADC_IN10, COMP1_INP; floating input after reset. |+| 9 | PC1 | bidirectional | 5 V tolerant GPIO PC1; alternate: LCD_SEG19; additional: ADC_IN11, COMP1_INP; floating input after reset. |+| 10 | PC2 | bidirectional | 5 V tolerant GPIO PC2; alternate: LCD_SEG20; additional: ADC_IN12, COMP1_INP; floating input after reset. |+| 11 | PC3 | bidirectional | Standard 3.3 V GPIO PC3; alternate: LCD_SEG21; additional: ADC_IN13, COMP1_INP; floating input after reset. |+| 12 | VSSA | power_in | Analog ground reference for ADC, DAC, comparators, and PLL; must be connected to VSS. |+| 13 | VDDA | power_in | Analog supply voltage 1.65-3.6 V (minimum 1.8 V when ADC or DAC is used); must be same voltage as VDD within 300 mV in operation. |+| 14 | PA0-WKUP1 | bidirectional | 5 V tolerant GPIO PA0; additional: WKUP1 wakeup from Standby, RTC_TAMP2, ADC_IN0, COMP1_INP; alternate: TIM2_CH1_ETR, TIM5_CH1, USART2_CTS. |+| 15 | PA1 | bidirectional | 5 V tolerant GPIO PA1; alternate: TIM2_CH2, TIM5_CH2, USART2_RTS, LCD_SEG0; additional: ADC_IN1, COMP1_INP, OPAMP1_VINP. |+| 16 | PA2 | bidirectional | 5 V tolerant GPIO PA2; alternate: TIM2_CH3, TIM5_CH3, TIM9_CH1, USART2_TX, LCD_SEG1; additional: ADC_IN2, COMP1_INP, OPAMP1_VINM. |+| 17 | PA3 | bidirectional | Standard 3.3 V GPIO PA3; alternate: TIM2_CH4, TIM5_CH4, TIM9_CH2, USART2_RX, LCD_SEG2; additional: ADC_IN3, COMP1_INP, OPAMP1_VOUT. |+| 18 | VSS_4 | power_in | Digital ground reference; must be connected to system ground; total sink current across all VSS pins ≤ 100 mA, per pin ≤ 70 mA. |+| 19 | VDD_4 | power_in | Main digital supply 1.65-3.6 V (BOR disabled) or 1.8-3.6 V (BOR enabled); source current per pin ≤ 70 mA, total across all VDD pins ≤ 100 mA. |+| 20 | PA4 | bidirectional | Standard 3.3 V GPIO PA4; alternate: SPI1_NSS, SPI3_NSS/I2S3_WS, USART2_CK; additional: ADC_IN4, DAC_OUT1, COMP1_INP. |+| 21 | PA5 | bidirectional | Standard 3.3 V GPIO PA5; alternate: TIM2_CH1_ETR, SPI1_SCK; additional: ADC_IN5, DAC_OUT2, COMP1_INP. |+| 22 | PA6 | bidirectional | 5 V tolerant GPIO PA6; alternate: TIM3_CH1, TIM10_CH1, SPI1_MISO, LCD_SEG3; additional: ADC_IN6, COMP1_INP, OPAMP2_VINP. |+| 23 | PA7 | bidirectional | 5 V tolerant GPIO PA7; alternate: TIM3_CH2, TIM11_CH1, SPI1_MOSI, LCD_SEG4; additional: ADC_IN7, COMP1_INP, OPAMP2_VINM. |+| 24 | PC4 | bidirectional | 5 V tolerant GPIO PC4; alternate: LCD_SEG22; additional: ADC_IN14, COMP1_INP; floating input after reset. |+| 25 | PC5 | bidirectional | 5 V tolerant GPIO PC5; alternate: LCD_SEG23; additional: ADC_IN15, COMP1_INP; floating input after reset. |+| 26 | PB0 | bidirectional | Standard 3.3 V GPIO PB0; alternate: TIM3_CH3, LCD_SEG5; additional: ADC_IN8, COMP1_INP, OPAMP2_VOUT, VLCDRAIL3, VREF_OUT. |+| 27 | PB1 | bidirectional | 5 V tolerant GPIO PB1; alternate: TIM3_CH4, LCD_SEG6; additional: ADC_IN9, COMP1_INP, VREF_OUT. |+| 28 | PB2 | bidirectional | 5 V tolerant GPIO PB2; sampled at reset as BOOT1 to determine boot memory source in combination with BOOT0; additional: VLCDRAIL1. |+| 29 | PB10 | bidirectional | 5 V tolerant GPIO PB10; alternate: TIM2_CH3, I2C2_SCL, USART3_TX, LCD_SEG10; floating input after reset. |+| 30 | PB11 | bidirectional | 5 V tolerant GPIO PB11; alternate: TIM2_CH4, I2C2_SDA, USART3_RX, LCD_SEG11; floating input after reset. |+| 31 | VSS_1 | power_in | Digital ground reference; must be connected to system ground; total sink current across all VSS pins ≤ 100 mA, per pin ≤ 70 mA. |+| 32 | VDD_1 | power_in | Main digital supply 1.65-3.6 V (BOR disabled) or 1.8-3.6 V (BOR enabled); source current per pin ≤ 70 mA, total across all VDD pins ≤ 100 mA. |+| 33 | PB12 | bidirectional | 5 V tolerant GPIO PB12; alternate: TIM10_CH1, I2C2_SMBA, SPI2_NSS/I2S2_WS, USART3_CK, LCD_SEG12; additional: ADC_IN18, VLCDRAIL2. |+| 34 | PB13 | bidirectional | 5 V tolerant GPIO PB13; alternate: TIM9_CH1, SPI2_SCK/I2S2_CK, USART3_CTS, LCD_SEG13; additional: ADC_IN19, COMP1_INP. |+| 35 | PB14 | bidirectional | 5 V tolerant GPIO PB14; alternate: TIM9_CH2, SPI2_MISO, USART3_RTS, LCD_SEG14; additional: ADC_IN20, COMP1_INP. |+| 36 | PB15 | bidirectional | 5 V tolerant GPIO PB15; alternate: TIM11_CH1, SPI2_MOSI/I2S2_SD, LCD_SEG15; additional: ADC_IN21, COMP1_INP, RTC_REFIN. |+| 37 | PC6 | bidirectional | 5 V tolerant GPIO PC6; alternate: TIM3_CH1, I2S2_MCK, LCD_SEG24; floating input after reset. |+| 38 | PC7 | bidirectional | 5 V tolerant GPIO PC7; alternate: TIM3_CH2, I2S3_MCK, LCD_SEG25; floating input after reset. |+| 39 | PC8 | bidirectional | 5 V tolerant GPIO PC8; alternate: TIM3_CH3, LCD_SEG26; floating input after reset. |+| 40 | PC9 | bidirectional | 5 V tolerant GPIO PC9; alternate: TIM3_CH4, LCD_SEG27; floating input after reset. |+| 41 | PA8 | bidirectional | 5 V tolerant GPIO PA8; alternate: USART1_CK, MCO (microcontroller clock output), LCD_COM0; floating input after reset. |+| 42 | PA9 | bidirectional | 5 V tolerant GPIO PA9; alternate: USART1_TX, LCD_COM1; floating input after reset. |+| 43 | PA10 | bidirectional | 5 V tolerant GPIO PA10; alternate: USART1_RX, LCD_COM2; floating input after reset. |+| 44 | PA11 | bidirectional | 5 V tolerant GPIO PA11; alternate: USART1_CTS, SPI1_MISO; additional: USB_DM (USB 2.0 full-speed 12 Mbit/s D− line); USB requires VDD ≥ 3.0 V. |+| 45 | PA12 | bidirectional | 5 V tolerant GPIO PA12; alternate: USART1_RTS, SPI1_MOSI; additional: USB_DP (USB 2.0 full-speed 12 Mbit/s D+ line); USB requires VDD ≥ 3.0 V. |+| 46 | PA13 | bidirectional | 5 V tolerant GPIO PA13; default function after reset is JTMS-SWDIO (JTAG/SWD data I/O shared with TMS); remappable to GPIO via AFIO. |+| 47 | VSS_2 | power_in | Digital ground reference; must be connected to system ground; total sink current across all VSS pins ≤ 100 mA, per pin ≤ 70 mA. |+| 48 | VDD_2 | power_in | Main digital supply 1.65-3.6 V (BOR disabled) or 1.8-3.6 V (BOR enabled); source current per pin ≤ 70 mA, total across all VDD pins ≤ 100 mA. |+| 49 | PA14 | bidirectional | 5 V tolerant GPIO PA14; default function after reset is JTCK-SWCLK (JTAG TCK / SWD clock shared with TCK); remappable to GPIO via AFIO. |+| 50 | PA15 | bidirectional | 5 V tolerant GPIO PA15; default function after reset is JTDI (JTAG data input); alternate: TIM2_CH1_ETR, SPI1_NSS, SPI3_NSS/I2S3_WS, LCD_SEG17. |+| 51 | PC10 | bidirectional | 5 V tolerant GPIO PC10; alternate: SPI3_SCK/I2S3_CK, USART3_TX, LCD_COM4/SEG28/SEG40; floating input after reset. |+| 52 | PC11 | bidirectional | 5 V tolerant GPIO PC11; alternate: SPI3_MISO, USART3_RX, LCD_COM5/SEG29/SEG41; floating input after reset. |+| 53 | PC12 | bidirectional | 5 V tolerant GPIO PC12; alternate: SPI3_MOSI/I2S3_SD, USART3_CK, LCD_COM6/SEG30/SEG42; floating input after reset. |+| 54 | PD2 | bidirectional | 5 V tolerant GPIO PD2; alternate: TIM3_ETR, LCD_COM7/SEG31/SEG43; floating input after reset. |+| 55 | PB3 | bidirectional | 5 V tolerant GPIO PB3; default function after reset is JTDO (JTAG data output); alternate: TIM2_CH2, SPI1_SCK, SPI3_SCK/I2S3_CK, LCD_SEG7; additional: COMP2_INM. |+| 56 | PB4 | bidirectional | 5 V tolerant GPIO PB4; default function after reset is NJTRST (JTAG reset); alternate: TIM3_CH1, SPI1_MISO, SPI3_MISO, LCD_SEG8; additional: COMP2_INP. |+| 57 | PB5 | bidirectional | 5 V tolerant GPIO PB5; alternate: TIM3_CH2, I2C1_SMBA, SPI1_MOSI, SPI3_MOSI/I2S3_SD, LCD_SEG9; additional: COMP2_INP. |+| 58 | PB6 | bidirectional | 5 V tolerant GPIO PB6; alternate: TIM4_CH1, I2C1_SCL, USART1_TX; additional: COMP2_INP. |+| 59 | PB7 | bidirectional | 5 V tolerant GPIO PB7; alternate: TIM4_CH2, I2C1_SDA, USART1_RX; additional: COMP2_INP, PVD_IN. |+| 60 | BOOT0 | input | Dedicated boot-mode selection input; sampled at reset to select Flash, System memory, or embedded RAM boot; input range 0-5.5 V; VIL max = 0.14 VDD, VIH min = 0.15 VDD + 0.56 V. |+| 61 | PB8 | bidirectional | 5 V tolerant GPIO PB8; alternate: TIM4_CH3, TIM10_CH1, I2C1_SCL, LCD_SEG16; floating input after reset. |+| 62 | PB9 | bidirectional | 5 V tolerant GPIO PB9; alternate: TIM4_CH4, TIM11_CH1, I2C1_SDA, LCD_COM3; floating input after reset. |+| 63 | VSS_3 | power_in | Digital ground reference; must be connected to system ground; total sink current across all VSS pins ≤ 100 mA, per pin ≤ 70 mA. |+| 64 | VDD_3 | power_in | Main digital supply 1.65-3.6 V (BOR disabled) or 1.8-3.6 V (BOR enabled); source current per pin ≤ 70 mA, total across all VDD pins ≤ 100 mA. |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | STMicroelectronics |+| Package | LQFP-64(10x10) |+| Category | Embedded Processors & Controllers |+| Pins | 64 |++## CAD (KiCad official)++- Symbol: `STM32L151RCT6`+- Footprint: `Package_QFP:LQFP-64_10x10mm_P0.5mm`+- 3D model: LQFP-64(10x10) (KiCad packages3D, STEP)+- 3D model files: `stm32l151rct6-etched.step` / `stm32l151rct6-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `stm32l151rct6.step` / `stm32l151rct6.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [STMicroelectronics datasheet](https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8588879670792368128) (136 pp, sha256 `5e6d5674cd06c108`, retrieved 2026-09-26, tier: lcsc)+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.2`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-4-6` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/stm32l151rct6-datasheet.pdf)
page.jsonadded+493
@@ -0,0 +1,493 @@+{+  "slug": "stm32l151rct6",+  "version": "0.1.0",+  "type": "component",+  "description": "STMicroelectronics Microcontrollers (MCU/MPU/SOC), LQFP-64(10x10). Pinout checked against ST's open pin data, KiCad symbol/footprint/3D.",+  "tags": [+    "component",+    "embedded processors & controllers",+    "stm32l151rct6",+    "factory-2.0.0",+    "extractor-text"+  ],+  "dependencies": {},+  "hero": {+    "type": "image",+    "path": "docs/hero.png"+  },+  "files": [+    "page.json",+    "README.md",+    "stm32l151rct6.kicad_sym",+    "stm32l151rct6.kicad_mod",+    "stm32l151rct6.glb",+    "stm32l151rct6.step",+    "stm32l151rct6.lbr",+    "docs/hero.png",+    "docs/stm32l151rct6-datasheet.pdf",+    "viewers/symbol.html",+    "viewers/footprint.html"+  ],+  "component": {+    "mpn": "STM32L151RCT6",+    "manufacturer": "STMicroelectronics",+    "package": "LQFP-64(10x10)",+    "pin_count": 64,+    "category": "Embedded Processors & Controllers",+    "subcategory": "Microcontrollers (MCU/MPU/SOC)",+    "datasheet": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8588879670792368128",+    "parts": {+      "symbol": "stm32l151rct6.kicad_sym",+      "footprint": "stm32l151rct6.kicad_mod",+      "model_3d": "stm32l151rct6-etched.glb",+      "model_3d_plain": "stm32l151rct6.glb",+      "model_3d_step": "stm32l151rct6-etched.step",+      "model_3d_step_plain": "stm32l151rct6.step",+      "lbr": "stm32l151rct6.lbr"+    },+    "distributor_links": {+      "lcsc": "C124721",+      "digikey": "497-17524-ND",+      "mouser": "511-STM32L151RCT6"+    },+    "distributor_check": {+      "checked_at": "2026-09-26T14:23:20Z",+      "source": "Component Ocean /api/assign-pns",+      "digikey": {+        "pn": "497-17524-ND",+        "status": "found"+      },+      "mouser": {+        "pn": "511-STM32L151RCT6",+        "status": "found"+      }+    },+    "pins": [+      {+        "number": "1",+        "name": "VLCD",+        "type": "power_in",+        "description": "LCD voltage supply; for STM32L151xC (no LCD controller) datasheet footnote 3 requires this pin be connected to VDD; max 3.6 V."+      },+      {+        "number": "2",+        "name": "PC13-WKUP2",+        "type": "bidirectional",+        "description": "5 V tolerant GPIO PC13; additional functions: WKUP2 wakeup from Standby, RTC_TAMP1, RTC_TS, RTC_OUT; floating input after reset."+      },+      {+        "number": "3",+        "name": "PC14-OSC32_IN",+        "type": "bidirectional",+        "description": "Standard 3.3 V GPIO PC14; shared with LSE 32.768 kHz oscillator input OSC32_IN when LSE is enabled (LSEON bit set); LSE has priority over GPIO."+      },+      {+        "number": "4",+        "name": "PC15-OSC32_OUT",+        "type": "bidirectional",+        "description": "Standard 3.3 V GPIO PC15; shared with LSE 32.768 kHz oscillator output OSC32_OUT when LSE is enabled; LSE has priority over GPIO."+      },+      {+        "number": "5",+        "name": "PH0-OSC_IN",+        "type": "bidirectional",+        "description": "Standard 3.3 V GPIO PH0; shared with HSE oscillator input OSC_IN (1-24 MHz) when HSE is enabled (HSEON bit set); HSE has priority over GPIO."+      },+      {+        "number": "6",+        "name": "PH1-OSC_OUT",+        "type": "bidirectional",+        "description": "Standard 3.3 V GPIO PH1; shared with HSE oscillator output OSC_OUT when HSE is enabled; HSE has priority over GPIO."+      },+      {+        "number": "7",+        "name": "NRST",+        "type": "bidirectional",+        "description": "Active-low reset; bidirectional with embedded 25-65 kΩ pull-up; filters pulses below 50 ns; VIL max = 0.3 VDD, VIH min = 0.39 VDD + 0.59 V; VOL max = 0.4 V at IOL = 2 mA."+      },+      {+        "number": "8",+        "name": "PC0",+        "type": "bidirectional",+        "description": "5 V tolerant GPIO PC0; alternate: LCD_SEG18; additional: ADC_IN10, COMP1_INP; floating input after reset."+      },+      {+        "number": "9",+        "name": "PC1",+        "type": "bidirectional",+        "description": "5 V tolerant GPIO PC1; alternate: LCD_SEG19; additional: ADC_IN11, COMP1_INP; floating input after reset."+      },+      {+        "number": "10",+        "name": "PC2",+        "type": "bidirectional",+        "description": "5 V tolerant GPIO PC2; alternate: LCD_SEG20; additional: ADC_IN12, COMP1_INP; floating input after reset."+      },+      {+        "number": "11",+        "name": "PC3",+        "type": "bidirectional",+        "description": "Standard 3.3 V GPIO PC3; alternate: LCD_SEG21; additional: ADC_IN13, COMP1_INP; floating input after reset."+      },+      {+        "number": "12",+        "name": "VSSA",+        "type": "power_in",+        "description": "Analog ground reference for ADC, DAC, comparators, and PLL; must be connected to VSS."+      },+      {+        "number": "13",+        "name": "VDDA",+        "type": "power_in",+        "description": "Analog supply voltage 1.65-3.6 V (minimum 1.8 V when ADC or DAC is used); must be same voltage as VDD within 300 mV in operation."+      },+      {+        "number": "14",+        "name": "PA0-WKUP1",+        "type": "bidirectional",+        "description": "5 V tolerant GPIO PA0; additional: WKUP1 wakeup from Standby, RTC_TAMP2, ADC_IN0, COMP1_INP; alternate: TIM2_CH1_ETR, TIM5_CH1, USART2_CTS."+      },+      {+        "number": "15",+        "name": "PA1",+        "type": "bidirectional",+        "description": "5 V tolerant GPIO PA1; alternate: TIM2_CH2, TIM5_CH2, USART2_RTS, LCD_SEG0; additional: ADC_IN1, COMP1_INP, OPAMP1_VINP."+      },+      {+        "number": "16",+        "name": "PA2",+        "type": "bidirectional",+        "description": "5 V tolerant GPIO PA2; alternate: TIM2_CH3, TIM5_CH3, TIM9_CH1, USART2_TX, LCD_SEG1; additional: ADC_IN2, COMP1_INP, OPAMP1_VINM."+      },+      {+        "number": "17",+        "name": "PA3",+        "type": "bidirectional",+        "description": "Standard 3.3 V GPIO PA3; alternate: TIM2_CH4, TIM5_CH4, TIM9_CH2, USART2_RX, LCD_SEG2; additional: ADC_IN3, COMP1_INP, OPAMP1_VOUT."+      },+      {+        "number": "18",+        "name": "VSS_4",+        "type": "power_in",+        "description": "Digital ground reference; must be connected to system ground; total sink current across all VSS pins ≤ 100 mA, per pin ≤ 70 mA."+      },+      {+        "number": "19",+        "name": "VDD_4",+        "type": "power_in",+        "description": "Main digital supply 1.65-3.6 V (BOR disabled) or 1.8-3.6 V (BOR enabled); source current per pin ≤ 70 mA, total across all VDD pins ≤ 100 mA."+      },+      {+        "number": "20",+        "name": "PA4",+        "type": "bidirectional",+        "description": "Standard 3.3 V GPIO PA4; alternate: SPI1_NSS, SPI3_NSS/I2S3_WS, USART2_CK; additional: ADC_IN4, DAC_OUT1, COMP1_INP."+      },+      {+        "number": "21",+        "name": "PA5",+        "type": "bidirectional",+        "description": "Standard 3.3 V GPIO PA5; alternate: TIM2_CH1_ETR, SPI1_SCK; additional: ADC_IN5, DAC_OUT2, COMP1_INP."+      },+      {+        "number": "22",+        "name": "PA6",+        "type": "bidirectional",+        "description": "5 V tolerant GPIO PA6; alternate: TIM3_CH1, TIM10_CH1, SPI1_MISO, LCD_SEG3; additional: ADC_IN6, COMP1_INP, OPAMP2_VINP."+      },+      {+        "number": "23",+        "name": "PA7",+        "type": "bidirectional",+        "description": "5 V tolerant GPIO PA7; alternate: TIM3_CH2, TIM11_CH1, SPI1_MOSI, LCD_SEG4; additional: ADC_IN7, COMP1_INP, OPAMP2_VINM."+      },+      {+        "number": "24",+        "name": "PC4",+        "type": "bidirectional",+        "description": "5 V tolerant GPIO PC4; alternate: LCD_SEG22; additional: ADC_IN14, COMP1_INP; floating input after reset."+      },+      {+        "number": "25",+        "name": "PC5",+        "type": "bidirectional",+        "description": "5 V tolerant GPIO PC5; alternate: LCD_SEG23; additional: ADC_IN15, COMP1_INP; floating input after reset."+      },+      {+        "number": "26",+        "name": "PB0",+        "type": "bidirectional",+        "description": "Standard 3.3 V GPIO PB0; alternate: TIM3_CH3, LCD_SEG5; additional: ADC_IN8, COMP1_INP, OPAMP2_VOUT, VLCDRAIL3, VREF_OUT."+      },+      {+        "number": "27",+        "name": "PB1",+        "type": "bidirectional",+        "description": "5 V tolerant GPIO PB1; alternate: TIM3_CH4, LCD_SEG6; additional: ADC_IN9, COMP1_INP, VREF_OUT."+      },+      {+        "number": "28",+        "name": "PB2",+        "type": "bidirectional",+        "description": "5 V tolerant GPIO PB2; sampled at reset as BOOT1 to determine boot memory source in combination with BOOT0; additional: VLCDRAIL1."+      },+      {+        "number": "29",+        "name": "PB10",+        "type": "bidirectional",+        "description": "5 V tolerant GPIO PB10; alternate: TIM2_CH3, I2C2_SCL, USART3_TX, LCD_SEG10; floating input after reset."+      },+      {+        "number": "30",+        "name": "PB11",+        "type": "bidirectional",+        "description": "5 V tolerant GPIO PB11; alternate: TIM2_CH4, I2C2_SDA, USART3_RX, LCD_SEG11; floating input after reset."+      },+      {+        "number": "31",+        "name": "VSS_1",+        "type": "power_in",+        "description": "Digital ground reference; must be connected to system ground; total sink current across all VSS pins ≤ 100 mA, per pin ≤ 70 mA."+      },+      {+        "number": "32",+        "name": "VDD_1",+        "type": "power_in",+        "description": "Main digital supply 1.65-3.6 V (BOR disabled) or 1.8-3.6 V (BOR enabled); source current per pin ≤ 70 mA, total across all VDD pins ≤ 100 mA."+      },+      {+        "number": "33",+        "name": "PB12",+        "type": "bidirectional",+        "description": "5 V tolerant GPIO PB12; alternate: TIM10_CH1, I2C2_SMBA, SPI2_NSS/I2S2_WS, USART3_CK, LCD_SEG12; additional: ADC_IN18, VLCDRAIL2."+      },+      {+        "number": "34",+        "name": "PB13",+        "type": "bidirectional",+        "description": "5 V tolerant GPIO PB13; alternate: TIM9_CH1, SPI2_SCK/I2S2_CK, USART3_CTS, LCD_SEG13; additional: ADC_IN19, COMP1_INP."+      },+      {+        "number": "35",+        "name": "PB14",+        "type": "bidirectional",+        "description": "5 V tolerant GPIO PB14; alternate: TIM9_CH2, SPI2_MISO, USART3_RTS, LCD_SEG14; additional: ADC_IN20, COMP1_INP."+      },+      {+        "number": "36",+        "name": "PB15",+        "type": "bidirectional",+        "description": "5 V tolerant GPIO PB15; alternate: TIM11_CH1, SPI2_MOSI/I2S2_SD, LCD_SEG15; additional: ADC_IN21, COMP1_INP, RTC_REFIN."+      },+      {+        "number": "37",+        "name": "PC6",+        "type": "bidirectional",+        "description": "5 V tolerant GPIO PC6; alternate: TIM3_CH1, I2S2_MCK, LCD_SEG24; floating input after reset."+      },+      {+        "number": "38",+        "name": "PC7",+        "type": "bidirectional",+        "description": "5 V tolerant GPIO PC7; alternate: TIM3_CH2, I2S3_MCK, LCD_SEG25; floating input after reset."+      },+      {+        "number": "39",+        "name": "PC8",+        "type": "bidirectional",+        "description": "5 V tolerant GPIO PC8; alternate: TIM3_CH3, LCD_SEG26; floating input after reset."+      },+      {+        "number": "40",+        "name": "PC9",+        "type": "bidirectional",+        "description": "5 V tolerant GPIO PC9; alternate: TIM3_CH4, LCD_SEG27; floating input after reset."+      },+      {+        "number": "41",+        "name": "PA8",+        "type": "bidirectional",+        "description": "5 V tolerant GPIO PA8; alternate: USART1_CK, MCO (microcontroller clock output), LCD_COM0; floating input after reset."+      },+      {+        "number": "42",+        "name": "PA9",+        "type": "bidirectional",+        "description": "5 V tolerant GPIO PA9; alternate: USART1_TX, LCD_COM1; floating input after reset."+      },+      {+        "number": "43",+        "name": "PA10",+        "type": "bidirectional",+        "description": "5 V tolerant GPIO PA10; alternate: USART1_RX, LCD_COM2; floating input after reset."+      },+      {+        "number": "44",+        "name": "PA11",+        "type": "bidirectional",+        "description": "5 V tolerant GPIO PA11; alternate: USART1_CTS, SPI1_MISO; additional: USB_DM (USB 2.0 full-speed 12 Mbit/s D− line); USB requires VDD ≥ 3.0 V."+      },+      {+        "number": "45",+        "name": "PA12",+        "type": "bidirectional",+        "description": "5 V tolerant GPIO PA12; alternate: USART1_RTS, SPI1_MOSI; additional: USB_DP (USB 2.0 full-speed 12 Mbit/s D+ line); USB requires VDD ≥ 3.0 V."+      },+      {+        "number": "46",+        "name": "PA13",+        "type": "bidirectional",+        "description": "5 V tolerant GPIO PA13; default function after reset is JTMS-SWDIO (JTAG/SWD data I/O shared with TMS); remappable to GPIO via AFIO."+      },+      {+        "number": "47",+        "name": "VSS_2",+        "type": "power_in",+        "description": "Digital ground reference; must be connected to system ground; total sink current across all VSS pins ≤ 100 mA, per pin ≤ 70 mA."+      },+      {+        "number": "48",+        "name": "VDD_2",+        "type": "power_in",+        "description": "Main digital supply 1.65-3.6 V (BOR disabled) or 1.8-3.6 V (BOR enabled); source current per pin ≤ 70 mA, total across all VDD pins ≤ 100 mA."+      },+      {+        "number": "49",+        "name": "PA14",+        "type": "bidirectional",+        "description": "5 V tolerant GPIO PA14; default function after reset is JTCK-SWCLK (JTAG TCK / SWD clock shared with TCK); remappable to GPIO via AFIO."+      },+      {+        "number": "50",+        "name": "PA15",+        "type": "bidirectional",+        "description": "5 V tolerant GPIO PA15; default function after reset is JTDI (JTAG data input); alternate: TIM2_CH1_ETR, SPI1_NSS, SPI3_NSS/I2S3_WS, LCD_SEG17."+      },+      {+        "number": "51",+        "name": "PC10",+        "type": "bidirectional",+        "description": "5 V tolerant GPIO PC10; alternate: SPI3_SCK/I2S3_CK, USART3_TX, LCD_COM4/SEG28/SEG40; floating input after reset."+      },+      {+        "number": "52",+        "name": "PC11",+        "type": "bidirectional",+        "description": "5 V tolerant GPIO PC11; alternate: SPI3_MISO, USART3_RX, LCD_COM5/SEG29/SEG41; floating input after reset."+      },+      {+        "number": "53",+        "name": "PC12",+        "type": "bidirectional",+        "description": "5 V tolerant GPIO PC12; alternate: SPI3_MOSI/I2S3_SD, USART3_CK, LCD_COM6/SEG30/SEG42; floating input after reset."+      },+      {+        "number": "54",+        "name": "PD2",+        "type": "bidirectional",+        "description": "5 V tolerant GPIO PD2; alternate: TIM3_ETR, LCD_COM7/SEG31/SEG43; floating input after reset."+      },+      {+        "number": "55",+        "name": "PB3",+        "type": "bidirectional",+        "description": "5 V tolerant GPIO PB3; default function after reset is JTDO (JTAG data output); alternate: TIM2_CH2, SPI1_SCK, SPI3_SCK/I2S3_CK, LCD_SEG7; additional: COMP2_INM."+      },+      {+        "number": "56",+        "name": "PB4",+        "type": "bidirectional",+        "description": "5 V tolerant GPIO PB4; default function after reset is NJTRST (JTAG reset); alternate: TIM3_CH1, SPI1_MISO, SPI3_MISO, LCD_SEG8; additional: COMP2_INP."+      },+      {+        "number": "57",+        "name": "PB5",+        "type": "bidirectional",+        "description": "5 V tolerant GPIO PB5; alternate: TIM3_CH2, I2C1_SMBA, SPI1_MOSI, SPI3_MOSI/I2S3_SD, LCD_SEG9; additional: COMP2_INP."+      },+      {+        "number": "58",+        "name": "PB6",+        "type": "bidirectional",+        "description": "5 V tolerant GPIO PB6; alternate: TIM4_CH1, I2C1_SCL, USART1_TX; additional: COMP2_INP."+      },+      {+        "number": "59",+        "name": "PB7",+        "type": "bidirectional",+        "description": "5 V tolerant GPIO PB7; alternate: TIM4_CH2, I2C1_SDA, USART1_RX; additional: COMP2_INP, PVD_IN."+      },+      {+        "number": "60",+        "name": "BOOT0",+        "type": "input",+        "description": "Dedicated boot-mode selection input; sampled at reset to select Flash, System memory, or embedded RAM boot; input range 0-5.5 V; VIL max = 0.14 VDD, VIH min = 0.15 VDD + 0.56 V."+      },+      {+        "number": "61",+        "name": "PB8",+        "type": "bidirectional",+        "description": "5 V tolerant GPIO PB8; alternate: TIM4_CH3, TIM10_CH1, I2C1_SCL, LCD_SEG16; floating input after reset."+      },+      {+        "number": "62",+        "name": "PB9",+        "type": "bidirectional",+        "description": "5 V tolerant GPIO PB9; alternate: TIM4_CH4, TIM11_CH1, I2C1_SDA, LCD_COM3; floating input after reset."+      },+      {+        "number": "63",+        "name": "VSS_3",+        "type": "power_in",+        "description": "Digital ground reference; must be connected to system ground; total sink current across all VSS pins ≤ 100 mA, per pin ≤ 70 mA."+      },+      {+        "number": "64",+        "name": "VDD_3",+        "type": "power_in",+        "description": "Main digital supply 1.65-3.6 V (BOR disabled) or 1.8-3.6 V (BOR enabled); source current per pin ≤ 70 mA, total across all VDD pins ≤ 100 mA."+      }+    ],+    "provenance": {+      "extractor": "extract_pins 0.2",+      "factory_chain": {+        "factory": "2.0.0",+        "extractor": "extract_pins 0.2",+        "primary_model": "claude-haiku-4-5-20251001",+        "primary_mode": "text",+        "consensus_model": "claude-sonnet-4-6",+        "consensus": "agreed",+        "guards": "pin_guards 0.1: passed",+        "guard_notes": [+          "extractor flagged: VLCD pin (pin 1) applies only to STM32L152xC devices with LCD; STM32L151xC should connect this to VD"+        ],+        "pages_sent": 136,+        "cost_usd": 1.6381,+        "at": "2026-09-26T14:22:52"+      },+      "datasheet": {+        "url": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8588879670792368128",+        "pages": 136,+        "sha256": "5e6d5674cd06c108",+        "source_tier": "lcsc"+      },+      "cad": "KiCad official (CC-BY-SA 4.0)",+      "pins": {+        "total": 64,+        "described": 64,+        "cites_pages": true,+        "refuses_to_fabricate": true+      }+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }+  },+  "visibility": "public",+  "org": "adom",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  }+}\ No newline at end of file