main
Ray
Publish 0.1.0
5a19ec3
STM32L151CCT7
STMicroelectronics · Microcontrollers (MCU/MPU/SOC) · LQFP-48(7x7)
STM32L151CCT7 from STMicroelectronics, in a LQFP-48(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model, then checked against ST open pin data); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VLCD | power_in | LCD supply pin; on STM32L151xC devices this pin should be connected to VDD, since the VLCD function applies to STM32L152xC only. |
| 2 | PC13 | bidirectional | 5 V tolerant (FT) I/O with default function PC13; additional functions WKUP2, RTC_TAMP1, RTC_TS and RTC_OUT. |
| 3 | PC14 | bidirectional | Standard 3.3 V (TC) I/O that is OSC32_IN when the LSE oscillator is on, otherwise a GPIO PC14. |
| 4 | PC15 | bidirectional | Standard 3.3 V (TC) I/O that is OSC32_OUT when the LSE oscillator is on, otherwise a GPIO PC15. |
| 5 | PH0 | bidirectional | Standard 3.3 V (TC) I/O that is OSC_IN when the HSE oscillator is on, otherwise a GPIO PH0. |
| 6 | PH1 | bidirectional | Standard 3.3 V (TC) I/O that is OSC_OUT when the HSE oscillator is on, otherwise a GPIO PH1. |
| 7 | NRST | bidirectional | Bidirectional reset pin with an embedded weak pull-up resistor (RST I/O structure). |
| 8 | VSSA | power_in | Analog ground pin that must be connected to VSS. |
| 9 | VDDA | power_in | Analog supply pin, 1.65 V to 3.6 V (minimum 1.8 V when the ADC is used), which must be connected to VDD. |
| 10 | PA0 | bidirectional | 5 V tolerant (FT) I/O; alternate functions TIM2_CH1_ETR, TIM5_CH1 and USART2_CTS; additional functions WKUP1, RTC_TAMP2, ADC_IN0 and COMP1_INP. |
| 11 | PA1 | bidirectional | 5 V tolerant (FT) I/O; alternate functions TIM2_CH2, TIM5_CH2, USART2_RTS and LCD_SEG0; additional functions ADC_IN1, COMP1_INP and OPAMP1_VINP. |
| 12 | PA2 | bidirectional | 5 V tolerant (FT) I/O; alternate functions TIM2_CH3, TIM5_CH3, TIM9_CH1, USART2_TX and LCD_SEG1; additional functions ADC_IN2, COMP1_INP and OPAMP1_VINM. |
| 13 | PA3 | bidirectional | Standard 3.3 V (TC) I/O; alternate functions TIM2_CH4, TIM5_CH4, TIM9_CH2, USART2_RX and LCD_SEG2; additional functions ADC_IN3, COMP1_INP and OPAMP1_VOUT. |
| 14 | PA4 | bidirectional | Standard 3.3 V (TC) I/O; alternate functions SPI1_NSS, SPI3_NSS, I2S3_WS and USART2_CK; additional functions ADC_IN4, DAC_OUT1 and COMP1_INP. |
| 15 | PA5 | bidirectional | Standard 3.3 V (TC) I/O; alternate functions TIM2_CH1_ETR and SPI1_SCK; additional functions ADC_IN5, DAC_OUT2 and COMP1_INP. |
| 16 | PA6 | bidirectional | 5 V tolerant (FT) I/O; alternate functions TIM3_CH1, TIM10_CH1, SPI1_MISO and LCD_SEG3; additional functions ADC_IN6, COMP1_INP and OPAMP2_VINP. |
| 17 | PA7 | bidirectional | 5 V tolerant (FT) I/O; alternate functions TIM3_CH2, TIM11_CH1, SPI1_MOSI and LCD_SEG4; additional functions ADC_IN7, COMP1_INP and OPAMP2_VINM. |
| 18 | PB0 | bidirectional | Standard 3.3 V (TC) I/O; alternate functions TIM3_CH3 and LCD_SEG5; additional functions ADC_IN8, COMP1_INP, OPAMP2_VOUT, VLCDRAIL3 and VREF_OUT. |
| 19 | PB1 | bidirectional | 5 V tolerant (FT) I/O; alternate functions TIM3_CH4 and LCD_SEG6; additional functions ADC_IN9, COMP1_INP and VREF_OUT. |
| 20 | PB2 | bidirectional | 5 V tolerant (FT) I/O that also serves as the BOOT1 pin; additional functions VLCDRAIL1 and ADCIN0b. |
| 21 | PB10 | bidirectional | 5 V tolerant (FT) I/O; alternate functions TIM2_CH3, I2C2_SCL, USART3_TX and LCD_SEG10. |
| 22 | PB11 | bidirectional | 5 V tolerant (FT) I/O; alternate functions TIM2_CH4, I2C2_SDA, USART3_RX and LCD_SEG11. |
| 23 | VSS_1 | power_in | Digital ground pin; the maximum current out of each VSS_x ground pin is -70 mA. |
| 24 | VDD_1 | power_in | Digital supply pin for the I/Os and internal regulator, 1.65 V to 3.6 V; the maximum current into each VDD_x pin is 70 mA. |
| 25 | PB12 | bidirectional | 5 V tolerant (FT) I/O; alternate functions TIM10_CH1, I2C2_SMBA, SPI2_NSS, I2S2_WS, USART3_CK and LCD_SEG12; additional functions ADC_IN18, COMP1_INP and VLCDRAIL2. |
| 26 | PB13 | bidirectional | 5 V tolerant (FT) I/O; alternate functions TIM9_CH1, SPI2_SCK, I2S2_CK, USART3_CTS and LCD_SEG13; additional functions ADC_IN19 and COMP1_INP. |
| 27 | PB14 | bidirectional | 5 V tolerant (FT) I/O; alternate functions TIM9_CH2, SPI2_MISO, USART3_RTS and LCD_SEG14; additional functions ADC_IN20 and COMP1_INP. |
| 28 | PB15 | bidirectional | 5 V tolerant (FT) I/O; alternate functions TIM11_CH1, SPI2_MOSI, I2S2_SD and LCD_SEG15; additional functions ADC_IN21, COMP1_INP and RTC_REFIN. |
| 29 | PA8 | bidirectional | 5 V tolerant (FT) I/O; alternate functions USART1_CK, MCO and LCD_COM0. |
| 30 | PA9 | bidirectional | 5 V tolerant (FT) I/O; alternate functions USART1_TX and LCD_COM1. |
| 31 | PA10 | bidirectional | 5 V tolerant (FT) I/O; alternate functions USART1_RX and LCD_COM2. |
| 32 | PA11 | bidirectional | 5 V tolerant (FT) I/O; alternate functions USART1_CTS and SPI1_MISO; additional function USB_DM. |
| 33 | PA12 | bidirectional | 5 V tolerant (FT) I/O; alternate functions USART1_RTS and SPI1_MOSI; additional function USB_DP. |
| 34 | PA13 | bidirectional | 5 V tolerant (FT) I/O with default function JTMS-SWDIO (serial wire debug data). |
| 35 | VSS_2 | power_in | Digital ground pin; the maximum current out of each VSS_x ground pin is -70 mA. |
| 36 | VDD_2 | power_in | Digital supply pin, 1.65 V to 3.6 V; the maximum current into each VDD_x pin is 70 mA. |
| 37 | PA14 | bidirectional | 5 V tolerant (FT) I/O with default function JTCK-SWCLK (serial wire debug clock). |
| 38 | PA15 | bidirectional | 5 V tolerant (FT) I/O with default function JTDI; alternate functions TIM2_CH1_ETR, SPI1_NSS, SPI3_NSS, I2S3_WS and LCD_SEG17. |
| 39 | PB3 | bidirectional | 5 V tolerant (FT) I/O with default function JTDO; alternate functions TIM2_CH2, SPI1_SCK, SPI3_SCK, I2S3_CK and LCD_SEG7; additional function COMP2_INM. |
| 40 | PB4 | bidirectional | 5 V tolerant (FT) I/O with default function NJTRST; alternate functions TIM3_CH1, SPI1_MISO, SPI3_MISO and LCD_SEG8; additional function COMP2_INP. |
| 41 | PB5 | bidirectional | 5 V tolerant (FT) I/O; alternate functions TIM3_CH2, I2C1_SMBA, SPI1_MOSI, SPI3_MOSI, I2S3_SD and LCD_SEG9; additional function COMP2_INP. |
| 42 | PB6 | bidirectional | 5 V tolerant (FT) I/O; alternate functions TIM4_CH1, I2C1_SCL and USART1_TX; additional function COMP2_INP. |
| 43 | PB7 | bidirectional | 5 V tolerant (FT) I/O; alternate functions TIM4_CH2, I2C1_SDA and USART1_RX; additional functions COMP2_INP and PVD_IN. |
| 44 | BOOT0 | input | Dedicated BOOT0 input that selects the boot mode at startup. |
| 45 | PB8 | bidirectional | 5 V tolerant (FT) I/O; alternate functions TIM4_CH3, TIM10_CH1, I2C1_SCL and LCD_SEG16. |
| 46 | PB9 | bidirectional | 5 V tolerant (FT) I/O; alternate functions TIM4_CH4, TIM11_CH1, I2C1_SDA and LCD_COM3. |
| 47 | VSS_3 | power_in | Digital ground pin; the maximum current out of each VSS_x ground pin is -70 mA. |
| 48 | VDD_3 | power_in | Digital supply pin, 1.65 V to 3.6 V; the maximum current into each VDD_x pin is 70 mA. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | LQFP-48(7x7) |
| Category | Embedded Processors & Controllers |
| Pins | 48 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| External main supply voltage (including VDDA and VDD) | VDD-VSS | -0.3 | 4 | V | Including VDDA and VDD | 55 | |
| Input voltage on any other pin | VIN | -0.3 | 4 | V | Any other pin (not five-volt tolerant) | 55 | |
| Variations between different VDD power pins | /ΔVDDx/ | 50 | mV | 55 | |||
| Variations between all different ground pins | /VSSx −VSS/ | 50 | mV | Include VREF- pin | 55 | ||
| Allowed voltage difference for VREF+ > VDDA | VREF+ -VDDA | 0.4 | V | VREF+ > VDDA | 55 | ||
| Total current into sum of all VDD_x power lines (source) | IVDD(Σ) | 100 | mA | 55 | |||
| Total current out of sum of all VSS_x ground lines (sink) | IVSS(Σ) | 100 | mA | 55 | |||
| Maximum current into each VDD_x power pin (source) | IVDD(PIN) | 70 | mA | 55 | |||
| Maximum current out of each VSS_x ground pin (sink) | IVSS(PIN) | -70 | mA | 55 | |||
| Output current sunk by any I/O and control pin | IIO | 25 | mA | 55 | |||
| Output current sourced by any I/O and control pin | IIO | -25 | mA | 55 | |||
| Total output current sunk by sum of all IOs and control pins | ΣIIO(PIN) | 60 | mA | 55 | |||
| Total output current sourced by sum of all IOs and control pins | ΣIIO(PIN) | -60 | mA | 55 | |||
| Injected current on five-volt tolerant I/O, RST and B pins | IINJ(PIN) | -5 | 0 | mA | Five-volt tolerant I/O, RST and B pins | 55 | |
| Injected current on any other pin | IINJ(PIN) | -5 | 5 | mA | Any other pin | 55 | |
| Total injected current (sum of all I/O and control pins) | ΣIINJ(PIN) | -25 | 25 | mA | Sum of all I/O and control pins | 55 | |
| Storage temperature range | TSTG | -65 | 150 | °C | 56 | ||
| Maximum junction temperature | TJ | 150 | °C | 56 | |||
| Internal AHB clock frequency | fHCLK | 0 | 32 | MHz | 56 | ||
| Internal APB1 clock frequency | fPCLK1 | 0 | 32 | MHz | 56 | ||
| Internal APB2 clock frequency | fPCLK2 | 0 | 32 | MHz | 56 | ||
| Standard operating voltage | VDD | 1.65 | 3.6 | V | BOR detector disabled | 56 | |
| Standard operating voltage | VDD | 1.8 | 3.6 | V | BOR detector enabled, at power on | 56 | |
| Analog operating voltage (ADC and DAC not used) | VDDA | 1.65 | 3.6 | V | Must be the same voltage as VDD | 56 | |
| Analog operating voltage (ADC or DAC used) | VDDA | 1.8 | 3.6 | V | ADC or DAC used | 56 | |
| I/O input voltage, FT pins | VIN | -0.3 | 5.5 | V | 2.0 V ≤ VDD | 56 | |
| I/O input voltage, FT pins | VIN | -0.3 | 5.25 | V | VDD < 2.0 V | 56 | |
| I/O input voltage, BOOT0 pin | VIN | 0 | 5.5 | V | BOOT0 pin | 56 | |
| Power dissipation, LQFP48 package | PD | 364 | mW | TA = 85 °C for suffix 6 or TA = 105 °C for suffix 7 | 56 | ||
| Ambient temperature for 7 suffix version | TA | -40 | 105 | °C | Maximum power dissipation | 57 | |
| Junction temperature range, 7 suffix version | TJ | -40 | 110 | °C | 7 suffix version | 57 | |
| VDD rise time rate | tVDD | 0 | 1000 | µs/V | BOR detector disabled | 57 | |
| VDD fall time rate | tVDD | 0 | 1000 | µs/V | BOR detector disabled | 57 | |
| Reset temporization | TRSTTEMPO | 2 | 3.3 | ms | VDD rising, BOR enabled | 57 | |
| Reset temporization | TRSTTEMPO | 0.4 | 0.7 | 1.6 | ms | VDD rising, BOR disabled (valid for device version without BOR at power up) | 57 |
| Power on/power down reset threshold | VPOR/PDR | 1 | 1.5 | 1.65 | V | Falling edge | 57 |
| Power on/power down reset threshold | VPOR/PDR | 1.3 | 1.5 | 1.65 | V | Rising edge | 57 |
| Brown-out reset threshold 0 | VBOR0 | 1.67 | 1.7 | 1.74 | V | Falling edge | 57 |
| Brown-out reset threshold 0 | VBOR0 | 1.69 | 1.76 | 1.8 | V | Rising edge | 57 |
| Brown-out reset threshold 1 | VBOR1 | 1.87 | 1.93 | 1.97 | V | Falling edge | 57 |
| Brown-out reset threshold 1 | VBOR1 | 1.96 | 2.03 | 2.07 | V | Rising edge | 57 |
| Brown-out reset threshold 2 | VBOR2 | 2.22 | 2.3 | 2.35 | V | Falling edge | 57 |
| Brown-out reset threshold 2 | VBOR2 | 2.31 | 2.41 | 2.44 | V | Rising edge | 57 |
| Brown-out reset threshold 3 | VBOR3 | 2.45 | 2.55 | 2.6 | V | Falling edge | 58 |
| Brown-out reset threshold 3 | VBOR3 | 2.54 | 2.66 | 2.7 | V | Rising edge | 58 |
| Brown-out reset threshold 4 | VBOR4 | 2.68 | 2.8 | 2.85 | V | Falling edge | 58 |
| Brown-out reset threshold 4 | VBOR4 | 2.78 | 2.9 | 2.95 | V | Rising edge | 58 |
| Internal reference voltage | VREFINT out | 1.202 | 1.224 | 1.242 | V | -40 °C < TJ < +110 °C | 59 |
| Internal reference current consumption | IREFINT | 1.4 | 2.3 | µA | 59 | ||
| Internal reference startup time | TVREFINT | 2 | 3 | ms | 59 | ||
| Temperature coefficient | TCoeff | 25 | 100 | ppm/°C | -40 °C < TJ < +110 °C | 59 | |
| Voltage coefficient | VDDCoeff | 2000 | ppm/V | 3.0 V < VDDA < 3.6 V | 59 | ||
| Long-term stability | ACoeff | 1000 | ppm | 1000 hours, T= 25 °C | 59 | ||
| Supply current in Stop mode (RTC disabled), regulator LP, LSI, HSI and HSE OFF | IDD (Stop) | 0.435 | 1 | µA | TA = -40°C to 25°C, no independent watchdog | 67 | |
| Supply current in Standby mode (RTC disabled), independent watchdog and LSI OFF | IDD (Standby) | 0.29 | 0.6 | µA | TA = -40 °C to 25 °C | 68 | |
| Supply current in Standby mode (RTC disabled), independent watchdog and LSI OFF | IDD (Standby) | 1.45 | 7 | µA | TA = 105 °C | 68 | |
| Max allowed current in Low-power run mode | IDD max (LP Run) | 200 | µA | VDD from 1.65 V to 3.6 V | 64 | ||
| Supply current in Run mode, code executed from Flash | IDD (Run from Flash) | 8.25 | 9.4 | mA | Range 1, VCORE=1.8 V, VOS[1:0] = 01, fHCLK 32 MHz | 61 | |
| Supply current in Run mode, code executed from RAM, Flash switched off | IDD (Run from RAM) | 7.15 | 8.3 | mA | Range 1, VCORE=1.8 V, VOS[1:0] = 01, fHCLK 32 MHz | 62 |
CAD (KiCad official)
- Symbol:
STM32L151CCT7 - Footprint:
Package_QFP:LQFP-48_7x7mm_P0.5mm - 3D model: LQFP-48(7x7) (KiCad packages3D, STEP)
- 3D model files:
stm32l151cct7-etched.step/stm32l151cct7-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);stm32l151cct7.step/stm32l151cct7.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: STMicroelectronics datasheet (136 pp, sha256
5e6d5674cd06c108, retrieved 2026-11-10, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# STM32L151CCT7
**STMicroelectronics** · Microcontrollers (MCU/MPU/SOC) · LQFP-48(7x7)
STM32L151CCT7 from STMicroelectronics, in a LQFP-48(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model, then checked against ST open pin data); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VLCD | power_in | LCD supply pin; on STM32L151xC devices this pin should be connected to VDD, since the VLCD function applies to STM32L152xC only. |
| 2 | PC13 | bidirectional | 5 V tolerant (FT) I/O with default function PC13; additional functions WKUP2, RTC_TAMP1, RTC_TS and RTC_OUT. |
| 3 | PC14 | bidirectional | Standard 3.3 V (TC) I/O that is OSC32_IN when the LSE oscillator is on, otherwise a GPIO PC14. |
| 4 | PC15 | bidirectional | Standard 3.3 V (TC) I/O that is OSC32_OUT when the LSE oscillator is on, otherwise a GPIO PC15. |
| 5 | PH0 | bidirectional | Standard 3.3 V (TC) I/O that is OSC_IN when the HSE oscillator is on, otherwise a GPIO PH0. |
| 6 | PH1 | bidirectional | Standard 3.3 V (TC) I/O that is OSC_OUT when the HSE oscillator is on, otherwise a GPIO PH1. |
| 7 | NRST | bidirectional | Bidirectional reset pin with an embedded weak pull-up resistor (RST I/O structure). |
| 8 | VSSA | power_in | Analog ground pin that must be connected to VSS. |
| 9 | VDDA | power_in | Analog supply pin, 1.65 V to 3.6 V (minimum 1.8 V when the ADC is used), which must be connected to VDD. |
| 10 | PA0 | bidirectional | 5 V tolerant (FT) I/O; alternate functions TIM2_CH1_ETR, TIM5_CH1 and USART2_CTS; additional functions WKUP1, RTC_TAMP2, ADC_IN0 and COMP1_INP. |
| 11 | PA1 | bidirectional | 5 V tolerant (FT) I/O; alternate functions TIM2_CH2, TIM5_CH2, USART2_RTS and LCD_SEG0; additional functions ADC_IN1, COMP1_INP and OPAMP1_VINP. |
| 12 | PA2 | bidirectional | 5 V tolerant (FT) I/O; alternate functions TIM2_CH3, TIM5_CH3, TIM9_CH1, USART2_TX and LCD_SEG1; additional functions ADC_IN2, COMP1_INP and OPAMP1_VINM. |
| 13 | PA3 | bidirectional | Standard 3.3 V (TC) I/O; alternate functions TIM2_CH4, TIM5_CH4, TIM9_CH2, USART2_RX and LCD_SEG2; additional functions ADC_IN3, COMP1_INP and OPAMP1_VOUT. |
| 14 | PA4 | bidirectional | Standard 3.3 V (TC) I/O; alternate functions SPI1_NSS, SPI3_NSS, I2S3_WS and USART2_CK; additional functions ADC_IN4, DAC_OUT1 and COMP1_INP. |
| 15 | PA5 | bidirectional | Standard 3.3 V (TC) I/O; alternate functions TIM2_CH1_ETR and SPI1_SCK; additional functions ADC_IN5, DAC_OUT2 and COMP1_INP. |
| 16 | PA6 | bidirectional | 5 V tolerant (FT) I/O; alternate functions TIM3_CH1, TIM10_CH1, SPI1_MISO and LCD_SEG3; additional functions ADC_IN6, COMP1_INP and OPAMP2_VINP. |
| 17 | PA7 | bidirectional | 5 V tolerant (FT) I/O; alternate functions TIM3_CH2, TIM11_CH1, SPI1_MOSI and LCD_SEG4; additional functions ADC_IN7, COMP1_INP and OPAMP2_VINM. |
| 18 | PB0 | bidirectional | Standard 3.3 V (TC) I/O; alternate functions TIM3_CH3 and LCD_SEG5; additional functions ADC_IN8, COMP1_INP, OPAMP2_VOUT, VLCDRAIL3 and VREF_OUT. |
| 19 | PB1 | bidirectional | 5 V tolerant (FT) I/O; alternate functions TIM3_CH4 and LCD_SEG6; additional functions ADC_IN9, COMP1_INP and VREF_OUT. |
| 20 | PB2 | bidirectional | 5 V tolerant (FT) I/O that also serves as the BOOT1 pin; additional functions VLCDRAIL1 and ADCIN0b. |
| 21 | PB10 | bidirectional | 5 V tolerant (FT) I/O; alternate functions TIM2_CH3, I2C2_SCL, USART3_TX and LCD_SEG10. |
| 22 | PB11 | bidirectional | 5 V tolerant (FT) I/O; alternate functions TIM2_CH4, I2C2_SDA, USART3_RX and LCD_SEG11. |
| 23 | VSS_1 | power_in | Digital ground pin; the maximum current out of each VSS_x ground pin is -70 mA. |
| 24 | VDD_1 | power_in | Digital supply pin for the I/Os and internal regulator, 1.65 V to 3.6 V; the maximum current into each VDD_x pin is 70 mA. |
| 25 | PB12 | bidirectional | 5 V tolerant (FT) I/O; alternate functions TIM10_CH1, I2C2_SMBA, SPI2_NSS, I2S2_WS, USART3_CK and LCD_SEG12; additional functions ADC_IN18, COMP1_INP and VLCDRAIL2. |
| 26 | PB13 | bidirectional | 5 V tolerant (FT) I/O; alternate functions TIM9_CH1, SPI2_SCK, I2S2_CK, USART3_CTS and LCD_SEG13; additional functions ADC_IN19 and COMP1_INP. |
| 27 | PB14 | bidirectional | 5 V tolerant (FT) I/O; alternate functions TIM9_CH2, SPI2_MISO, USART3_RTS and LCD_SEG14; additional functions ADC_IN20 and COMP1_INP. |
| 28 | PB15 | bidirectional | 5 V tolerant (FT) I/O; alternate functions TIM11_CH1, SPI2_MOSI, I2S2_SD and LCD_SEG15; additional functions ADC_IN21, COMP1_INP and RTC_REFIN. |
| 29 | PA8 | bidirectional | 5 V tolerant (FT) I/O; alternate functions USART1_CK, MCO and LCD_COM0. |
| 30 | PA9 | bidirectional | 5 V tolerant (FT) I/O; alternate functions USART1_TX and LCD_COM1. |
| 31 | PA10 | bidirectional | 5 V tolerant (FT) I/O; alternate functions USART1_RX and LCD_COM2. |
| 32 | PA11 | bidirectional | 5 V tolerant (FT) I/O; alternate functions USART1_CTS and SPI1_MISO; additional function USB_DM. |
| 33 | PA12 | bidirectional | 5 V tolerant (FT) I/O; alternate functions USART1_RTS and SPI1_MOSI; additional function USB_DP. |
| 34 | PA13 | bidirectional | 5 V tolerant (FT) I/O with default function JTMS-SWDIO (serial wire debug data). |
| 35 | VSS_2 | power_in | Digital ground pin; the maximum current out of each VSS_x ground pin is -70 mA. |
| 36 | VDD_2 | power_in | Digital supply pin, 1.65 V to 3.6 V; the maximum current into each VDD_x pin is 70 mA. |
| 37 | PA14 | bidirectional | 5 V tolerant (FT) I/O with default function JTCK-SWCLK (serial wire debug clock). |
| 38 | PA15 | bidirectional | 5 V tolerant (FT) I/O with default function JTDI; alternate functions TIM2_CH1_ETR, SPI1_NSS, SPI3_NSS, I2S3_WS and LCD_SEG17. |
| 39 | PB3 | bidirectional | 5 V tolerant (FT) I/O with default function JTDO; alternate functions TIM2_CH2, SPI1_SCK, SPI3_SCK, I2S3_CK and LCD_SEG7; additional function COMP2_INM. |
| 40 | PB4 | bidirectional | 5 V tolerant (FT) I/O with default function NJTRST; alternate functions TIM3_CH1, SPI1_MISO, SPI3_MISO and LCD_SEG8; additional function COMP2_INP. |
| 41 | PB5 | bidirectional | 5 V tolerant (FT) I/O; alternate functions TIM3_CH2, I2C1_SMBA, SPI1_MOSI, SPI3_MOSI, I2S3_SD and LCD_SEG9; additional function COMP2_INP. |
| 42 | PB6 | bidirectional | 5 V tolerant (FT) I/O; alternate functions TIM4_CH1, I2C1_SCL and USART1_TX; additional function COMP2_INP. |
| 43 | PB7 | bidirectional | 5 V tolerant (FT) I/O; alternate functions TIM4_CH2, I2C1_SDA and USART1_RX; additional functions COMP2_INP and PVD_IN. |
| 44 | BOOT0 | input | Dedicated BOOT0 input that selects the boot mode at startup. |
| 45 | PB8 | bidirectional | 5 V tolerant (FT) I/O; alternate functions TIM4_CH3, TIM10_CH1, I2C1_SCL and LCD_SEG16. |
| 46 | PB9 | bidirectional | 5 V tolerant (FT) I/O; alternate functions TIM4_CH4, TIM11_CH1, I2C1_SDA and LCD_COM3. |
| 47 | VSS_3 | power_in | Digital ground pin; the maximum current out of each VSS_x ground pin is -70 mA. |
| 48 | VDD_3 | power_in | Digital supply pin, 1.65 V to 3.6 V; the maximum current into each VDD_x pin is 70 mA. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | LQFP-48(7x7) |
| Category | Embedded Processors & Controllers |
| Pins | 48 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| External main supply voltage (including VDDA and VDD) | VDD-VSS | -0.3 | | 4 | V | Including VDDA and VDD | 55 |
| Input voltage on any other pin | VIN | -0.3 | | 4 | V | Any other pin (not five-volt tolerant) | 55 |
| Variations between different VDD power pins | /ΔVDDx/ | | | 50 | mV | | 55 |
| Variations between all different ground pins | /VSSx −VSS/ | | | 50 | mV | Include VREF- pin | 55 |
| Allowed voltage difference for VREF+ > VDDA | VREF+ -VDDA | | | 0.4 | V | VREF+ > VDDA | 55 |
| Total current into sum of all VDD_x power lines (source) | IVDD(Σ) | | | 100 | mA | | 55 |
| Total current out of sum of all VSS_x ground lines (sink) | IVSS(Σ) | | | 100 | mA | | 55 |
| Maximum current into each VDD_x power pin (source) | IVDD(PIN) | | | 70 | mA | | 55 |
| Maximum current out of each VSS_x ground pin (sink) | IVSS(PIN) | | | -70 | mA | | 55 |
| Output current sunk by any I/O and control pin | IIO | | | 25 | mA | | 55 |
| Output current sourced by any I/O and control pin | IIO | | | -25 | mA | | 55 |
| Total output current sunk by sum of all IOs and control pins | ΣIIO(PIN) | | | 60 | mA | | 55 |
| Total output current sourced by sum of all IOs and control pins | ΣIIO(PIN) | | | -60 | mA | | 55 |
| Injected current on five-volt tolerant I/O, RST and B pins | IINJ(PIN) | -5 | | 0 | mA | Five-volt tolerant I/O, RST and B pins | 55 |
| Injected current on any other pin | IINJ(PIN) | -5 | | 5 | mA | Any other pin | 55 |
| Total injected current (sum of all I/O and control pins) | ΣIINJ(PIN) | -25 | | 25 | mA | Sum of all I/O and control pins | 55 |
| Storage temperature range | TSTG | -65 | | 150 | °C | | 56 |
| Maximum junction temperature | TJ | | | 150 | °C | | 56 |
| Internal AHB clock frequency | fHCLK | 0 | | 32 | MHz | | 56 |
| Internal APB1 clock frequency | fPCLK1 | 0 | | 32 | MHz | | 56 |
| Internal APB2 clock frequency | fPCLK2 | 0 | | 32 | MHz | | 56 |
| Standard operating voltage | VDD | 1.65 | | 3.6 | V | BOR detector disabled | 56 |
| Standard operating voltage | VDD | 1.8 | | 3.6 | V | BOR detector enabled, at power on | 56 |
| Analog operating voltage (ADC and DAC not used) | VDDA | 1.65 | | 3.6 | V | Must be the same voltage as VDD | 56 |
| Analog operating voltage (ADC or DAC used) | VDDA | 1.8 | | 3.6 | V | ADC or DAC used | 56 |
| I/O input voltage, FT pins | VIN | -0.3 | | 5.5 | V | 2.0 V ≤ VDD | 56 |
| I/O input voltage, FT pins | VIN | -0.3 | | 5.25 | V | VDD < 2.0 V | 56 |
| I/O input voltage, BOOT0 pin | VIN | 0 | | 5.5 | V | BOOT0 pin | 56 |
| Power dissipation, LQFP48 package | PD | | | 364 | mW | TA = 85 °C for suffix 6 or TA = 105 °C for suffix 7 | 56 |
| Ambient temperature for 7 suffix version | TA | -40 | | 105 | °C | Maximum power dissipation | 57 |
| Junction temperature range, 7 suffix version | TJ | -40 | | 110 | °C | 7 suffix version | 57 |
| VDD rise time rate | tVDD | 0 | | 1000 | µs/V | BOR detector disabled | 57 |
| VDD fall time rate | tVDD | 0 | | 1000 | µs/V | BOR detector disabled | 57 |
| Reset temporization | TRSTTEMPO | | 2 | 3.3 | ms | VDD rising, BOR enabled | 57 |
| Reset temporization | TRSTTEMPO | 0.4 | 0.7 | 1.6 | ms | VDD rising, BOR disabled (valid for device version without BOR at power up) | 57 |
| Power on/power down reset threshold | VPOR/PDR | 1 | 1.5 | 1.65 | V | Falling edge | 57 |
| Power on/power down reset threshold | VPOR/PDR | 1.3 | 1.5 | 1.65 | V | Rising edge | 57 |
| Brown-out reset threshold 0 | VBOR0 | 1.67 | 1.7 | 1.74 | V | Falling edge | 57 |
| Brown-out reset threshold 0 | VBOR0 | 1.69 | 1.76 | 1.8 | V | Rising edge | 57 |
| Brown-out reset threshold 1 | VBOR1 | 1.87 | 1.93 | 1.97 | V | Falling edge | 57 |
| Brown-out reset threshold 1 | VBOR1 | 1.96 | 2.03 | 2.07 | V | Rising edge | 57 |
| Brown-out reset threshold 2 | VBOR2 | 2.22 | 2.3 | 2.35 | V | Falling edge | 57 |
| Brown-out reset threshold 2 | VBOR2 | 2.31 | 2.41 | 2.44 | V | Rising edge | 57 |
| Brown-out reset threshold 3 | VBOR3 | 2.45 | 2.55 | 2.6 | V | Falling edge | 58 |
| Brown-out reset threshold 3 | VBOR3 | 2.54 | 2.66 | 2.7 | V | Rising edge | 58 |
| Brown-out reset threshold 4 | VBOR4 | 2.68 | 2.8 | 2.85 | V | Falling edge | 58 |
| Brown-out reset threshold 4 | VBOR4 | 2.78 | 2.9 | 2.95 | V | Rising edge | 58 |
| Internal reference voltage | VREFINT out | 1.202 | 1.224 | 1.242 | V | -40 °C < TJ < +110 °C | 59 |
| Internal reference current consumption | IREFINT | | 1.4 | 2.3 | µA | | 59 |
| Internal reference startup time | TVREFINT | | 2 | 3 | ms | | 59 |
| Temperature coefficient | TCoeff | | 25 | 100 | ppm/°C | -40 °C < TJ < +110 °C | 59 |
| Voltage coefficient | VDDCoeff | | | 2000 | ppm/V | 3.0 V < VDDA < 3.6 V | 59 |
| Long-term stability | ACoeff | | | 1000 | ppm | 1000 hours, T= 25 °C | 59 |
| Supply current in Stop mode (RTC disabled), regulator LP, LSI, HSI and HSE OFF | IDD (Stop) | | 0.435 | 1 | µA | TA = -40°C to 25°C, no independent watchdog | 67 |
| Supply current in Standby mode (RTC disabled), independent watchdog and LSI OFF | IDD (Standby) | | 0.29 | 0.6 | µA | TA = -40 °C to 25 °C | 68 |
| Supply current in Standby mode (RTC disabled), independent watchdog and LSI OFF | IDD (Standby) | | 1.45 | 7 | µA | TA = 105 °C | 68 |
| Max allowed current in Low-power run mode | IDD max (LP Run) | | | 200 | µA | VDD from 1.65 V to 3.6 V | 64 |
| Supply current in Run mode, code executed from Flash | IDD (Run from Flash) | | 8.25 | 9.4 | mA | Range 1, VCORE=1.8 V, VOS[1:0] = 01, fHCLK 32 MHz | 61 |
| Supply current in Run mode, code executed from RAM, Flash switched off | IDD (Run from RAM) | | 7.15 | 8.3 | mA | Range 1, VCORE=1.8 V, VOS[1:0] = 01, fHCLK 32 MHz | 62 |
## CAD (KiCad official)
- Symbol: `STM32L151CCT7`
- Footprint: `Package_QFP:LQFP-48_7x7mm_P0.5mm`
- 3D model: LQFP-48(7x7) (KiCad packages3D, STEP)
- 3D model files: `stm32l151cct7-etched.step` / `stm32l151cct7-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `stm32l151cct7.step` / `stm32l151cct7.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [STMicroelectronics datasheet](https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8588942008148353024) (136 pp, sha256 `5e6d5674cd06c108`, retrieved 2026-11-10, tier: lcsc)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/stm32l151cct7-datasheet.pdf)