main
Download ZIP Propose a change
Generated by kicad-footprint-generator · KiCad file format 20260206
Name Last commit message Last updated
docs Publish 0.1.0 · Ray
viewers stm32l151cbu6a: viewers rendered from the public page · Ray
package.json Publish 0.1.0 · Ray
page.json Set visibility: public · Ray
README.md Publish 0.1.0 · Ray
stm32l151cbu6a-etched.glb Publish 0.1.0 · Ray
stm32l151cbu6a-etched.step stm32l151cbu6a: factory component page (tier=mfr) · Ray
stm32l151cbu6a-hero.glb stm32l151cbu6a: hero GLB from the etched model (keeps the MPN mark) · Ray
stm32l151cbu6a-hero.overlay.json Publish 0.1.0 · Ray
stm32l151cbu6a.glb Publish 0.1.0 · Ray
stm32l151cbu6a.kicad_mod Publish 0.1.0 · Ray
stm32l151cbu6a.kicad_sym Publish 0.1.0 · Ray
stm32l151cbu6a.lbr Publish 0.1.0 · Ray
stm32l151cbu6a.step Publish 0.1.0 · Ray
verification.json Verified: Published by the parts factory: tier mfr, 49 pins · Ray

STM32L151CBU6A

STMicroelectronics · Microcontrollers (MCU/MPU/SOC) · UFQFPN-48(7x7)

STM32L151CBU6A from STMicroelectronics, in a UFQFPN-48(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model, then checked against ST open pin data); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VLCD power_in LCD supply pin (VLCD); on STM32L151xxxxA devices it should be connected to VDD, since the LCD function is only applicable to STM32L152xxxxA devices.
2 PC13 bidirectional 5 V tolerant (FT) GPIO, reset state floating input, with additional functions RTC_TAMP1, RTC_TS, RTC_OUT and WKUP2 wakeup.
3 PC14-OSC32_IN bidirectional Standard 3.3 V (TC) I/O that operates as the OSC32_IN LSE input only when the LSE oscillator is on (LSEON set in RCC_CSR), otherwise it is usable as GPIO PC14.
4 PC15-OSC32_OUT bidirectional Standard 3.3 V (TC) I/O that operates as the OSC32_OUT LSE output only when the LSE oscillator is on (LSEON set in RCC_CSR), otherwise it is usable as GPIO PC15.
5 PH0-OSC_IN bidirectional Standard 3.3 V (TC) I/O that operates as the OSC_IN HSE input only when the HSE oscillator is on (HSEON set in RCC_CR), otherwise it is usable as GPIO PH0.
6 PH1-OSC_OUT bidirectional Standard 3.3 V (TC) I/O that operates as the OSC_OUT HSE output only when the HSE oscillator is on (HSEON set in RCC_CR), otherwise it is usable as GPIO PH1.
7 NRST bidirectional Active-low bidirectional reset pin with embedded weak pull-up (RPU 25 to 65 kΩ, typ. 45 kΩ), with VIL(NRST) max 0.3 VDD.
8 VSSA power_in Analog ground for the ADC, reset blocks, RCs and PLL; VDDA and VSSA must be connected to VDD and VSS respectively.
9 VDDA power_in Analog supply for the ADC, reset blocks, RCs and PLL, 1.65 V to 3.6 V, with a minimum of 1.8 V when the ADC is used; it must be connected to VDD.
10 PA0-WKUP1 bidirectional 5 V tolerant (FT) GPIO with WKUP1 wakeup, ADC_IN0 and COMP1 input functions, plus alternate function USART2_CTS/TIM2_CH1_ETR.
11 PA1 bidirectional 5 V tolerant (FT) GPIO with ADC_IN1 and COMP1 input functions, plus alternate functions USART2_RTS, TIM2_CH2 and LCD_SEG0.
12 PA2 bidirectional 5 V tolerant (FT) GPIO with ADC_IN2 and COMP1 input functions, plus alternate functions USART2_TX, TIM2_CH3, TIM9_CH1 and LCD_SEG1.
13 PA3 bidirectional Standard 3.3 V (TC) GPIO with ADC_IN3 and COMP1 input functions, plus alternate functions USART2_RX, TIM2_CH4, TIM9_CH2 and LCD_SEG2.
14 PA4 bidirectional Standard 3.3 V (TC) GPIO with ADC_IN4, DAC_OUT1 and COMP1 input functions, plus alternate functions SPI1_NSS and USART2_CK.
15 PA5 bidirectional Standard 3.3 V (TC) GPIO with ADC_IN5, DAC_OUT2 and COMP1 input functions, plus alternate functions SPI1_SCK and TIM2_CH1_ETR.
16 PA6 bidirectional 5 V tolerant (FT) GPIO with ADC_IN6 and COMP1 input functions, plus alternate functions SPI1_MISO, TIM3_CH1, LCD_SEG3 and TIM10_CH1.
17 PA7 bidirectional 5 V tolerant (FT) GPIO with ADC_IN7 and COMP1 input functions, plus alternate functions SPI1_MOSI, TIM3_CH2, LCD_SEG4 and TIM11_CH1.
18 PB0 bidirectional Standard 3.3 V (TC) GPIO with ADC_IN8, COMP1 input and VREF_OUT functions, plus alternate functions TIM3_CH3, LCD_SEG5 and VLCDRAIL3.
19 PB1 bidirectional 5 V tolerant (FT) GPIO with ADC_IN9, COMP1 input and VREF_OUT functions, plus alternate functions TIM3_CH4 and LCD_SEG6.
20 PB2 bidirectional 5 V tolerant (FT) GPIO with BOOT1 function and VLCDRAIL1 LCD decoupling function.
21 PB10 bidirectional 5 V tolerant (FT) GPIO with alternate functions I2C2_SCL, USART3_TX, TIM2_CH3 and LCD_SEG10.
22 PB11 bidirectional 5 V tolerant (FT) GPIO with alternate functions I2C2_SDA, USART3_RX, TIM2_CH4 and LCD_SEG11.
23 VSS_1 power_in Ground pin for the digital supply domain; it must be connected to the ground plane.
24 VDD_1 power_in Digital supply pin, 1.65 V to 3.6 V (VDD), which powers the I/Os and the internal regulator.
25 PB12 bidirectional 5 V tolerant (FT) GPIO with ADC_IN18 and COMP1 input functions, plus alternate functions SPI2_NSS, I2C2_SMBA, USART3_CK, LCD_SEG12, TIM10_CH1 and VLCDRAIL2.
26 PB13 bidirectional 5 V tolerant (FT) GPIO with ADC_IN19 and COMP1 input functions, plus alternate functions SPI2_SCK, USART3_CTS, LCD_SEG13 and TIM9_CH1.
27 PB14 bidirectional 5 V tolerant (FT) GPIO with ADC_IN20 and COMP1 input functions, plus alternate functions SPI2_MISO, USART3_RTS, LCD_SEG14 and TIM9_CH2.
28 PB15 bidirectional 5 V tolerant (FT) GPIO with ADC_IN21, COMP1 input and RTC_REFIN functions, plus alternate functions SPI2_MOSI, LCD_SEG15 and TIM11_CH1.
29 PA8 bidirectional 5 V tolerant (FT) GPIO with alternate functions USART1_CK, MCO and LCD_COM0.
30 PA9 bidirectional 5 V tolerant (FT) GPIO with alternate functions USART1_TX and LCD_COM1.
31 PA10 bidirectional 5 V tolerant (FT) GPIO with alternate functions USART1_RX and LCD_COM2.
32 PA11 bidirectional 5 V tolerant (FT) GPIO with alternate functions USART1_CTS, SPI1_MISO and USB_DM.
33 PA12 bidirectional 5 V tolerant (FT) GPIO with alternate functions USART1_RTS, SPI1_MOSI and USB_DP.
34 PA13 bidirectional 5 V tolerant (FT) GPIO; in its default function it is the JTMS-SWDIO serial wire debug data pin.
35 VSS_2 power_in Ground pin for the digital supply domain; it must be connected to the ground plane.
36 VDD_2 power_in Digital supply pin, 1.65 V to 3.6 V (VDD), which powers the I/Os and the internal regulator.
37 PA14 bidirectional 5 V tolerant (FT) GPIO; in its default function it is the JTCK-SWCLK serial wire debug clock pin.
38 PA15 bidirectional 5 V tolerant (FT) GPIO with alternate functions JTDI, TIM2_CH1_ETR, SPI1_NSS and LCD_SEG17.
39 PB3 bidirectional 5 V tolerant (FT) GPIO with COMP2_INM input, plus alternate functions JTDO, TIM2_CH2, SPI1_SCK and LCD_SEG7.
40 PB4 bidirectional 5 V tolerant (FT) GPIO with COMP2_INP input, plus alternate functions NJTRST, TIM3_CH1, SPI1_MISO and LCD_SEG8.
41 PB5 bidirectional 5 V tolerant (FT) GPIO with COMP2_INP input, plus alternate functions I2C1_SMBA, TIM3_CH2, SPI1_MOSI and LCD_SEG9.
42 PB6 bidirectional 5 V tolerant (FT) GPIO with alternate functions I2C1_SCL, TIM4_CH1 and USART1_TX.
43 PB7 bidirectional 5 V tolerant (FT) GPIO with PVD_IN input, plus alternate functions I2C1_SDA, TIM4_CH2 and USART1_RX.
44 BOOT0 input Dedicated BOOT0 boot-mode selection input, specified up to 5.5 V on the input voltage limit.
45 PB8 bidirectional 5 V tolerant (FT) GPIO with alternate functions TIM4_CH3, I2C1_SCL, LCD_SEG16 and TIM10_CH1.
46 PB9 bidirectional 5 V tolerant (FT) GPIO with alternate functions TIM4_CH4, I2C1_SDA, LCD_COM3 and TIM11_CH1.
47 VSS_3 power_in Ground pin for the digital supply domain; it must be connected to the ground plane.
48 VDD_3 power_in Digital supply pin, 1.65 V to 3.6 V (VDD), which powers the I/Os and the internal regulator.
49 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer STMicroelectronics
Package UFQFPN-48(7x7)
Category Embedded Processors & Controllers
Pins 49

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Internal AHB clock frequency fHCLK 0 32 MHz 56
Internal APB1 clock frequency fPCLK1 0 32 MHz 56
Internal APB2 clock frequency fPCLK2 0 32 MHz 56
Standard operating voltage VDD 1.65 3.6 V BOR detector disabled 56
Standard operating voltage VDD 1.8 3.6 V BOR detector enabled, at power on 56
Analog operating voltage VDDA 1.65 3.6 V ADC and DAC not used; must be the same voltage as VDD 56
Analog operating voltage VDDA 1.8 3.6 V ADC or DAC used 56
I/O input voltage VIN -0.3 5.5 V FT pins: 2.0 V ≤ VDD 56
I/O input voltage VIN -0.3 5.25 V FT pins: VDD < 2.0 V 56
I/O input voltage VIN 0 5.5 V BOOT0 56
I/O input voltage VIN -0.3 V Any other pin (max printed as VDD+0.3) 56
Power dissipation PD 606 mW UFQFPN48 package; TA = 85 °C for suffix 6 57
Ambient temperature for 6 suffix version TA -40 85 °C Maximum power dissipation 57
Junction temperature range 6 suffix version TJ -40 105 °C 57
External main supply voltage (including VDDA and VDD) VDD-VSS -0.3 4 V 55
Input voltage on any other pin VIN 4 V Input voltage on any other pin 55
Variations between different VDD power pins /ΔVDDx/ 50 mV 55
Variations between all different ground pins /VSSX −VSS/ 50 mV Include VREF- pin 55
Allowed voltage difference for VREF+ > VDDA VREF+ −VDDA 0.4 V VREF+ > VDDA 55
Total current into sum of all VDD_x power lines (source) ΣIVDD 100 mA 55
Total current out of sum of all VSS_x ground lines (sink) ΣIVSS 100 mA 55
Maximum current into each VDD_x power pin (source) IVDD(PIN) 70 mA 55
Maximum current out of each VSS_x ground pin (sink) IVSS(PIN) -70 mA 55
Output current sunk by any I/O and control pin IIO 25 mA Sunk 55
Output current sourced by any I/O and control pin IIO -25 mA Sourced 55
Total output current sunk by sum of all IOs and control pins ΣIIO(PIN) 60 mA Sunk 55
Total output current sourced by sum of all IOs and control pins ΣIIO(PIN) -60 mA Sourced 55
Injected current on five-volt tolerant I/O IINJ(PIN) -5 0 mA RST and B pins 55
Injected current on any other pin IINJ(PIN) -5 5 mA Any other pin 55
Total injected current (sum of all I/O and control pins) ΣIINJ(PIN) -25 25 mA 55
Storage temperature range TSTG -65 150 °C 56
Maximum junction temperature TJ 150 °C 56
Power on/power down reset threshold VPOR/PDR 1 1.5 1.65 V Falling edge 57
Power on/power down reset threshold VPOR/PDR 1.3 1.5 1.65 V Rising edge 57
Brown-out reset threshold 0 VBOR0 1.67 1.7 1.74 V Falling edge 58
Brown-out reset threshold 0 VBOR0 1.69 1.76 1.8 V Rising edge 58
Brown-out reset threshold 1 VBOR1 1.87 1.93 1.97 V Falling edge 58
Brown-out reset threshold 1 VBOR1 1.96 2.03 2.07 V Rising edge 58
Brown-out reset threshold 2 VBOR2 2.22 2.3 2.35 V Falling edge 58
Brown-out reset threshold 2 VBOR2 2.31 2.41 2.44 V Rising edge 58
Brown-out reset threshold 3 VBOR3 2.45 2.55 2.6 V Falling edge 58
Brown-out reset threshold 3 VBOR3 2.54 2.66 2.7 V Rising edge 58
Brown-out reset threshold 4 VBOR4 2.68 2.8 2.85 V Falling edge 58
Brown-out reset threshold 4 VBOR4 2.78 2.9 2.95 V Rising edge 58
Internal reference voltage VREFINT out 1.202 1.224 1.242 V -40 °C < TJ < +110 °C 59
Internal reference current consumption IREFINT 1.4 2.3 µA 59
Internal reference startup time TVREFINT 2 3 ms 59
Temperature coefficient TCoeff 25 100 ppm/°C -40 °C < TJ < +110 °C 59
Long-term stability ACoeff 1000 ppm 1000 hours, T = 25 °C 59
Voltage coefficient VDDCoeff 2000 ppm/V 3.0 V < VDDA < 3.6 V 59
High-speed external user clock source frequency fHSE_ext 1 32 MHz CSS is on or PLL is used 72
Low-speed external user clock source frequency fLSE_ext 1 32.768 1000 kHz 73
Oscillator frequency fOSC_IN 1 24 MHz 73
Supply current in Run mode, code executed from Flash (HSI 16 MHz clock source, Range 1) IDD (Run from Flash) 8.2 10.2 mA Range 1, VCORE=1.8 V, VOS[1:0]=01, fHCLK = 32 MHz 61
Supply current in Low-power run mode IDD (LP Run) 10.9 12 µA All peripherals OFF, code from RAM, Flash OFF, MSI 65 kHz, fHCLK = 32 kHz, TA = -40 °C to 25 °C 64
Supply current in Stop mode with RTC enabled IDD (Stop with RTC) 3.3 10 µA RTC clocked by LSI, regulator in LP mode, HSI and HSE OFF, LCD OFF, TA = 85 °C 66
Supply current in Stop mode (RTC disabled) IDD (Stop) 2.35 9 µA Regulator in LP mode, LSI, HSI and HSE OFF (no independent watchdog), TA = 85 °C 67
Supply current in Standby mode with RTC enabled IDD (Standby with RTC) 1.35 4 µA RTC clocked by LSI (no independent watchdog), TA = 85 °C 68
Supply current in Standby mode with RTC disabled IDD (Standby) 0.52 2.75 µA Independent watchdog and LSI OFF, TA = 85 °C 68

Materials and finish

As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).

Part Material Colour / plating Datasheet says Page
contacts tin TLEAD Maximum lead temperature during soldering see note (1) 1. Compliant with JEDEC Std J-STD-020D (for small body, Sn-Pb or Pb assembly), the ST ECOPACK® 56

CAD (KiCad official)

  • Symbol: STM32L151CBU6A
  • Footprint: Package_DFN_QFN:QFN-48-1EP_7x7mm_P0.5mm_EP5.15x5.15mm
  • 3D model: UFQFPN-48(7x7), generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 0.55 mm tall, datasheet A, nominal). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
  • 3D model files: stm32l151cbu6a-etched.step / stm32l151cbu6a-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); stm32l151cbu6a.step / stm32l151cbu6a.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: STMicroelectronics datasheet (130 pp, sha256 e5e0ab791f4e7879, retrieved 2026-11-10, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF