3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Contents
README
markdownSTM32L151CBU6A
STMicroelectronics · Microcontrollers (MCU/MPU/SOC) · UFQFPN-48(7x7)
STM32L151CBU6A from STMicroelectronics, in a UFQFPN-48(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model, then checked against ST open pin data); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VLCD | power_in | LCD supply pin (VLCD); on STM32L151xxxxA devices it should be connected to VDD, since the LCD function is only applicable to STM32L152xxxxA devices. |
| 2 | PC13 | bidirectional | 5 V tolerant (FT) GPIO, reset state floating input, with additional functions RTC_TAMP1, RTC_TS, RTC_OUT and WKUP2 wakeup. |
| 3 | PC14-OSC32_IN | bidirectional | Standard 3.3 V (TC) I/O that operates as the OSC32_IN LSE input only when the LSE oscillator is on (LSEON set in RCC_CSR), otherwise it is usable as GPIO PC14. |
| 4 | PC15-OSC32_OUT | bidirectional | Standard 3.3 V (TC) I/O that operates as the OSC32_OUT LSE output only when the LSE oscillator is on (LSEON set in RCC_CSR), otherwise it is usable as GPIO PC15. |
| 5 | PH0-OSC_IN | bidirectional | Standard 3.3 V (TC) I/O that operates as the OSC_IN HSE input only when the HSE oscillator is on (HSEON set in RCC_CR), otherwise it is usable as GPIO PH0. |
| 6 | PH1-OSC_OUT | bidirectional | Standard 3.3 V (TC) I/O that operates as the OSC_OUT HSE output only when the HSE oscillator is on (HSEON set in RCC_CR), otherwise it is usable as GPIO PH1. |
| 7 | NRST | bidirectional | Active-low bidirectional reset pin with embedded weak pull-up (RPU 25 to 65 kΩ, typ. 45 kΩ), with VIL(NRST) max 0.3 VDD. |
| 8 | VSSA | power_in | Analog ground for the ADC, reset blocks, RCs and PLL; VDDA and VSSA must be connected to VDD and VSS respectively. |
| 9 | VDDA | power_in | Analog supply for the ADC, reset blocks, RCs and PLL, 1.65 V to 3.6 V, with a minimum of 1.8 V when the ADC is used; it must be connected to VDD. |
| 10 | PA0-WKUP1 | bidirectional | 5 V tolerant (FT) GPIO with WKUP1 wakeup, ADC_IN0 and COMP1 input functions, plus alternate function USART2_CTS/TIM2_CH1_ETR. |
| 11 | PA1 | bidirectional | 5 V tolerant (FT) GPIO with ADC_IN1 and COMP1 input functions, plus alternate functions USART2_RTS, TIM2_CH2 and LCD_SEG0. |
| 12 | PA2 | bidirectional | 5 V tolerant (FT) GPIO with ADC_IN2 and COMP1 input functions, plus alternate functions USART2_TX, TIM2_CH3, TIM9_CH1 and LCD_SEG1. |
| 13 | PA3 | bidirectional | Standard 3.3 V (TC) GPIO with ADC_IN3 and COMP1 input functions, plus alternate functions USART2_RX, TIM2_CH4, TIM9_CH2 and LCD_SEG2. |
| 14 | PA4 | bidirectional | Standard 3.3 V (TC) GPIO with ADC_IN4, DAC_OUT1 and COMP1 input functions, plus alternate functions SPI1_NSS and USART2_CK. |
| 15 | PA5 | bidirectional | Standard 3.3 V (TC) GPIO with ADC_IN5, DAC_OUT2 and COMP1 input functions, plus alternate functions SPI1_SCK and TIM2_CH1_ETR. |
| 16 | PA6 | bidirectional | 5 V tolerant (FT) GPIO with ADC_IN6 and COMP1 input functions, plus alternate functions SPI1_MISO, TIM3_CH1, LCD_SEG3 and TIM10_CH1. |
| 17 | PA7 | bidirectional | 5 V tolerant (FT) GPIO with ADC_IN7 and COMP1 input functions, plus alternate functions SPI1_MOSI, TIM3_CH2, LCD_SEG4 and TIM11_CH1. |
| 18 | PB0 | bidirectional | Standard 3.3 V (TC) GPIO with ADC_IN8, COMP1 input and VREF_OUT functions, plus alternate functions TIM3_CH3, LCD_SEG5 and VLCDRAIL3. |
| 19 | PB1 | bidirectional | 5 V tolerant (FT) GPIO with ADC_IN9, COMP1 input and VREF_OUT functions, plus alternate functions TIM3_CH4 and LCD_SEG6. |
| 20 | PB2 | bidirectional | 5 V tolerant (FT) GPIO with BOOT1 function and VLCDRAIL1 LCD decoupling function. |
| 21 | PB10 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions I2C2_SCL, USART3_TX, TIM2_CH3 and LCD_SEG10. |
| 22 | PB11 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions I2C2_SDA, USART3_RX, TIM2_CH4 and LCD_SEG11. |
| 23 | VSS_1 | power_in | Ground pin for the digital supply domain; it must be connected to the ground plane. |
| 24 | VDD_1 | power_in | Digital supply pin, 1.65 V to 3.6 V (VDD), which powers the I/Os and the internal regulator. |
| 25 | PB12 | bidirectional | 5 V tolerant (FT) GPIO with ADC_IN18 and COMP1 input functions, plus alternate functions SPI2_NSS, I2C2_SMBA, USART3_CK, LCD_SEG12, TIM10_CH1 and VLCDRAIL2. |
| 26 | PB13 | bidirectional | 5 V tolerant (FT) GPIO with ADC_IN19 and COMP1 input functions, plus alternate functions SPI2_SCK, USART3_CTS, LCD_SEG13 and TIM9_CH1. |
| 27 | PB14 | bidirectional | 5 V tolerant (FT) GPIO with ADC_IN20 and COMP1 input functions, plus alternate functions SPI2_MISO, USART3_RTS, LCD_SEG14 and TIM9_CH2. |
| 28 | PB15 | bidirectional | 5 V tolerant (FT) GPIO with ADC_IN21, COMP1 input and RTC_REFIN functions, plus alternate functions SPI2_MOSI, LCD_SEG15 and TIM11_CH1. |
| 29 | PA8 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions USART1_CK, MCO and LCD_COM0. |
| 30 | PA9 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions USART1_TX and LCD_COM1. |
| 31 | PA10 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions USART1_RX and LCD_COM2. |
| 32 | PA11 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions USART1_CTS, SPI1_MISO and USB_DM. |
| 33 | PA12 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions USART1_RTS, SPI1_MOSI and USB_DP. |
| 34 | PA13 | bidirectional | 5 V tolerant (FT) GPIO; in its default function it is the JTMS-SWDIO serial wire debug data pin. |
| 35 | VSS_2 | power_in | Ground pin for the digital supply domain; it must be connected to the ground plane. |
| 36 | VDD_2 | power_in | Digital supply pin, 1.65 V to 3.6 V (VDD), which powers the I/Os and the internal regulator. |
| 37 | PA14 | bidirectional | 5 V tolerant (FT) GPIO; in its default function it is the JTCK-SWCLK serial wire debug clock pin. |
| 38 | PA15 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions JTDI, TIM2_CH1_ETR, SPI1_NSS and LCD_SEG17. |
| 39 | PB3 | bidirectional | 5 V tolerant (FT) GPIO with COMP2_INM input, plus alternate functions JTDO, TIM2_CH2, SPI1_SCK and LCD_SEG7. |
| 40 | PB4 | bidirectional | 5 V tolerant (FT) GPIO with COMP2_INP input, plus alternate functions NJTRST, TIM3_CH1, SPI1_MISO and LCD_SEG8. |
| 41 | PB5 | bidirectional | 5 V tolerant (FT) GPIO with COMP2_INP input, plus alternate functions I2C1_SMBA, TIM3_CH2, SPI1_MOSI and LCD_SEG9. |
| 42 | PB6 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions I2C1_SCL, TIM4_CH1 and USART1_TX. |
| 43 | PB7 | bidirectional | 5 V tolerant (FT) GPIO with PVD_IN input, plus alternate functions I2C1_SDA, TIM4_CH2 and USART1_RX. |
| 44 | BOOT0 | input | Dedicated BOOT0 boot-mode selection input, specified up to 5.5 V on the input voltage limit. |
| 45 | PB8 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions TIM4_CH3, I2C1_SCL, LCD_SEG16 and TIM10_CH1. |
| 46 | PB9 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions TIM4_CH4, I2C1_SDA, LCD_COM3 and TIM11_CH1. |
| 47 | VSS_3 | power_in | Ground pin for the digital supply domain; it must be connected to the ground plane. |
| 48 | VDD_3 | power_in | Digital supply pin, 1.65 V to 3.6 V (VDD), which powers the I/Os and the internal regulator. |
| 49 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | UFQFPN-48(7x7) |
| Category | Embedded Processors & Controllers |
| Pins | 49 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Internal AHB clock frequency | fHCLK | 0 | 32 | MHz | 56 | ||
| Internal APB1 clock frequency | fPCLK1 | 0 | 32 | MHz | 56 | ||
| Internal APB2 clock frequency | fPCLK2 | 0 | 32 | MHz | 56 | ||
| Standard operating voltage | VDD | 1.65 | 3.6 | V | BOR detector disabled | 56 | |
| Standard operating voltage | VDD | 1.8 | 3.6 | V | BOR detector enabled, at power on | 56 | |
| Analog operating voltage | VDDA | 1.65 | 3.6 | V | ADC and DAC not used; must be the same voltage as VDD | 56 | |
| Analog operating voltage | VDDA | 1.8 | 3.6 | V | ADC or DAC used | 56 | |
| I/O input voltage | VIN | -0.3 | 5.5 | V | FT pins: 2.0 V ≤ VDD | 56 | |
| I/O input voltage | VIN | -0.3 | 5.25 | V | FT pins: VDD < 2.0 V | 56 | |
| I/O input voltage | VIN | 0 | 5.5 | V | BOOT0 | 56 | |
| I/O input voltage | VIN | -0.3 | V | Any other pin (max printed as VDD+0.3) | 56 | ||
| Power dissipation | PD | 606 | mW | UFQFPN48 package; TA = 85 °C for suffix 6 | 57 | ||
| Ambient temperature for 6 suffix version | TA | -40 | 85 | °C | Maximum power dissipation | 57 | |
| Junction temperature range 6 suffix version | TJ | -40 | 105 | °C | 57 | ||
| External main supply voltage (including VDDA and VDD) | VDD-VSS | -0.3 | 4 | V | 55 | ||
| Input voltage on any other pin | VIN | 4 | V | Input voltage on any other pin | 55 | ||
| Variations between different VDD power pins | /ΔVDDx/ | 50 | mV | 55 | |||
| Variations between all different ground pins | /VSSX −VSS/ | 50 | mV | Include VREF- pin | 55 | ||
| Allowed voltage difference for VREF+ > VDDA | VREF+ −VDDA | 0.4 | V | VREF+ > VDDA | 55 | ||
| Total current into sum of all VDD_x power lines (source) | ΣIVDD | 100 | mA | 55 | |||
| Total current out of sum of all VSS_x ground lines (sink) | ΣIVSS | 100 | mA | 55 | |||
| Maximum current into each VDD_x power pin (source) | IVDD(PIN) | 70 | mA | 55 | |||
| Maximum current out of each VSS_x ground pin (sink) | IVSS(PIN) | -70 | mA | 55 | |||
| Output current sunk by any I/O and control pin | IIO | 25 | mA | Sunk | 55 | ||
| Output current sourced by any I/O and control pin | IIO | -25 | mA | Sourced | 55 | ||
| Total output current sunk by sum of all IOs and control pins | ΣIIO(PIN) | 60 | mA | Sunk | 55 | ||
| Total output current sourced by sum of all IOs and control pins | ΣIIO(PIN) | -60 | mA | Sourced | 55 | ||
| Injected current on five-volt tolerant I/O | IINJ(PIN) | -5 | 0 | mA | RST and B pins | 55 | |
| Injected current on any other pin | IINJ(PIN) | -5 | 5 | mA | Any other pin | 55 | |
| Total injected current (sum of all I/O and control pins) | ΣIINJ(PIN) | -25 | 25 | mA | 55 | ||
| Storage temperature range | TSTG | -65 | 150 | °C | 56 | ||
| Maximum junction temperature | TJ | 150 | °C | 56 | |||
| Power on/power down reset threshold | VPOR/PDR | 1 | 1.5 | 1.65 | V | Falling edge | 57 |
| Power on/power down reset threshold | VPOR/PDR | 1.3 | 1.5 | 1.65 | V | Rising edge | 57 |
| Brown-out reset threshold 0 | VBOR0 | 1.67 | 1.7 | 1.74 | V | Falling edge | 58 |
| Brown-out reset threshold 0 | VBOR0 | 1.69 | 1.76 | 1.8 | V | Rising edge | 58 |
| Brown-out reset threshold 1 | VBOR1 | 1.87 | 1.93 | 1.97 | V | Falling edge | 58 |
| Brown-out reset threshold 1 | VBOR1 | 1.96 | 2.03 | 2.07 | V | Rising edge | 58 |
| Brown-out reset threshold 2 | VBOR2 | 2.22 | 2.3 | 2.35 | V | Falling edge | 58 |
| Brown-out reset threshold 2 | VBOR2 | 2.31 | 2.41 | 2.44 | V | Rising edge | 58 |
| Brown-out reset threshold 3 | VBOR3 | 2.45 | 2.55 | 2.6 | V | Falling edge | 58 |
| Brown-out reset threshold 3 | VBOR3 | 2.54 | 2.66 | 2.7 | V | Rising edge | 58 |
| Brown-out reset threshold 4 | VBOR4 | 2.68 | 2.8 | 2.85 | V | Falling edge | 58 |
| Brown-out reset threshold 4 | VBOR4 | 2.78 | 2.9 | 2.95 | V | Rising edge | 58 |
| Internal reference voltage | VREFINT out | 1.202 | 1.224 | 1.242 | V | -40 °C < TJ < +110 °C | 59 |
| Internal reference current consumption | IREFINT | 1.4 | 2.3 | µA | 59 | ||
| Internal reference startup time | TVREFINT | 2 | 3 | ms | 59 | ||
| Temperature coefficient | TCoeff | 25 | 100 | ppm/°C | -40 °C < TJ < +110 °C | 59 | |
| Long-term stability | ACoeff | 1000 | ppm | 1000 hours, T = 25 °C | 59 | ||
| Voltage coefficient | VDDCoeff | 2000 | ppm/V | 3.0 V < VDDA < 3.6 V | 59 | ||
| High-speed external user clock source frequency | fHSE_ext | 1 | 32 | MHz | CSS is on or PLL is used | 72 | |
| Low-speed external user clock source frequency | fLSE_ext | 1 | 32.768 | 1000 | kHz | 73 | |
| Oscillator frequency | fOSC_IN | 1 | 24 | MHz | 73 | ||
| Supply current in Run mode, code executed from Flash (HSI 16 MHz clock source, Range 1) | IDD (Run from Flash) | 8.2 | 10.2 | mA | Range 1, VCORE=1.8 V, VOS[1:0]=01, fHCLK = 32 MHz | 61 | |
| Supply current in Low-power run mode | IDD (LP Run) | 10.9 | 12 | µA | All peripherals OFF, code from RAM, Flash OFF, MSI 65 kHz, fHCLK = 32 kHz, TA = -40 °C to 25 °C | 64 | |
| Supply current in Stop mode with RTC enabled | IDD (Stop with RTC) | 3.3 | 10 | µA | RTC clocked by LSI, regulator in LP mode, HSI and HSE OFF, LCD OFF, TA = 85 °C | 66 | |
| Supply current in Stop mode (RTC disabled) | IDD (Stop) | 2.35 | 9 | µA | Regulator in LP mode, LSI, HSI and HSE OFF (no independent watchdog), TA = 85 °C | 67 | |
| Supply current in Standby mode with RTC enabled | IDD (Standby with RTC) | 1.35 | 4 | µA | RTC clocked by LSI (no independent watchdog), TA = 85 °C | 68 | |
| Supply current in Standby mode with RTC disabled | IDD (Standby) | 0.52 | 2.75 | µA | Independent watchdog and LSI OFF, TA = 85 °C | 68 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | tin | TLEAD Maximum lead temperature during soldering see note (1) 1. Compliant with JEDEC Std J-STD-020D (for small body, Sn-Pb or Pb assembly), the ST ECOPACK® | 56 |
CAD (KiCad official)
- Symbol:
STM32L151CBU6A - Footprint:
Package_DFN_QFN:QFN-48-1EP_7x7mm_P0.5mm_EP5.15x5.15mm - 3D model: UFQFPN-48(7x7), generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 0.55 mm tall, datasheet A, nominal). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
- 3D model files:
stm32l151cbu6a-etched.step/stm32l151cbu6a-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);stm32l151cbu6a.step/stm32l151cbu6a.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: STMicroelectronics datasheet (130 pp, sha256
e5e0ab791f4e7879, retrieved 2026-11-10, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).