3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownSTM32L011D4P7
STMicroelectronics · ST Microelectronics · TSSOP-14
STM32L011D4P7 from STMicroelectronics, in a TSSOP-14. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model, then checked against ST open pin data); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | PB9-BOOT0 | input | Input-only dedicated BOOT0 pin that selects the boot memory; the datasheet lists no alternate functions for PB9 on this package. |
| 2 | PC14-OSC32_IN | bidirectional | 5 V tolerant (FT) I/O that serves as the OSC32_IN low-speed oscillator input. |
| 3 | PC15-OSC32_OUT | bidirectional | Standard 3.3 V I/O (TC) that serves as the OSC32_OUT low-speed oscillator output. |
| 4 | NRST | bidirectional | Active-low bidirectional reset pin with embedded weak pull-up, acting as device reset input and internal reset output. |
| 5 | PA0-CK_IN | bidirectional | 3.3 V tolerant I/O (TTa) connected directly to the ADC, with ADC_IN0 and USART2_RX among its functions. |
| 6 | PA1 | bidirectional | 5 V tolerant I/O (FT) with ADC_IN1 and COMP1_INP, plus USART2_RTS_DE and LPUART1_TX among its alternate functions. |
| 7 | PA4 | bidirectional | 3.3 V tolerant I/O (TTa) connected directly to the ADC, with ADC_IN4, SPI1_NSS and USART2_CK among its functions. |
| 8 | PA7 | bidirectional | 5 V tolerant I/O (FT) with SPI1_MOSI, USART2_CTS and ADC_IN7 among its functions. |
| 9 | VSS | power_in | Digital and analog ground pin. |
| 10 | VDD | power_in | Digital power supply pin; on the TSSOP14 package VDDA is internally connected to this pin. |
| 11 | PA9 | bidirectional | 5 V tolerant I/O with Fast Mode Plus capability (FTf), with MCO, I2C1_SCL and USART2_TX among its functions. |
| 12 | PA10 | bidirectional | 5 V tolerant I/O with Fast Mode Plus capability (FTf), with I2C1_SDA, USART2_RX and TIM21_CH1 among its functions. |
| 13 | PA13 | bidirectional | 5 V tolerant I/O with Fast Mode Plus capability (FTf) that carries SWDIO for serial wire debug. |
| 14 | PA14 | bidirectional | 5 V tolerant I/O (FT) that carries SWCLK; on TSSOP14 it drives SPI1_MISO as an output while the bootloader is active, so first programming needs connect-under-reset over SWD to disable the bootloader. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | TSSOP-14 |
| Category | Embedded Processors & Controllers |
| Pins | 14 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage VDD-VSS (external main supply, incl. VDDA, VDD) | VDD-VSS | -0.3 | 4 | V | including VDDA, VDD | 46 | |
| Input voltage on TC pins | VIN | 4 | V | TC pins | 46 | ||
| Input voltage on any other pin | VIN | 4 | V | any other pin | 46 | ||
| Variation between different VDDx power pins | /ΔVDD/ | 50 | mV | 46 | |||
| Variation between any VDDx and VDDA power pins | /VDDA-VDDx/ | 300 | mV | 46 | |||
| Variation between all different ground pins | /ΔVSS/ | 50 | mV | 46 | |||
| Total current into sum of all VDD power lines (source) | ΣIVDD | 105 | mA | 47 | |||
| Total current out of sum of all VSS ground lines (sink) | ΣIVSS | 105 | mA | 47 | |||
| Maximum current into each VDD power pin (source) | IVDD(PIN) | 100 | mA | 47 | |||
| Maximum current out of each VSS ground pin (sink) | IVSS(PIN) | 100 | mA | 47 | |||
| Output current sunk by any I/O and control pin except FTf pins | IIO | 16 | mA | except FTf pins | 47 | ||
| Output current sunk by FTf pins | IIO | 22 | mA | FTf pins | 47 | ||
| Output current sourced by any I/O and control pin | IIO | -16 | mA | 47 | |||
| Total output current sunk by sum of all IOs and control pins | ΣIIO(PIN) | 90 | mA | sum of all IOs and control pins | 47 | ||
| Total output current sourced by sum of all IOs and control pins | ΣIIO(PIN) | -90 | mA | sum of all IOs and control pins | 47 | ||
| Injected current on FT, FTf, RST and B pins | IINJ(PIN) | -5 | 0 | mA | FT, FTf, RST and B pins | 47 | |
| Injected current on TC pin | IINJ(PIN) | -5 | 5 | mA | TC pin | 47 | |
| Total injected current (sum of all I/O and control pins) | ΣIINJ(PIN) | -25 | 25 | mA | 47 | ||
| Storage temperature range | TSTG | -65 | 150 | °C | 47 | ||
| Maximum junction temperature | TJ | 150 | °C | 47 | |||
| Internal AHB clock frequency | fHCLK | 0 | 32 | MHz | 48 | ||
| Internal APB1 clock frequency | fPCLK1 | 0 | 32 | MHz | 48 | ||
| Internal APB2 clock frequency | fPCLK2 | 0 | 32 | MHz | 48 | ||
| Standard operating voltage | VDD | 1.65 | 3.6 | V | BOR detector disabled | 48 | |
| Standard operating voltage | VDD | 1.8 | 3.6 | V | BOR detector enabled, at power on | 48 | |
| Analog operating voltage (all features) | VDDA | 1.65 | 3.6 | V | Must be the same voltage as VDD | 48 | |
| Input voltage on FT, FTf and RST pins | VIN | -0.3 | 5.5 | V | 2.0 V ≤ VDD ≤ 3.6 V | 48 | |
| Input voltage on FT, FTf and RST pins | VIN | -0.3 | 5.2 | V | 1.65 V ≤ VDD ≤ 2.0 V | 48 | |
| Input voltage on BOOT0 pin | VIN | 0 | 5.5 | V | 48 | ||
| Input voltage on TC pin | VIN | -0.3 | V | 48 | |||
| Power dissipation, TSSOP14 package | PD | 210 | mW | TA = 85 °C (range 6) or TA = 105 °C (range 7) | 48 | ||
| Power dissipation, TSSOP14 package | PD | 53 | mW | TA = 125 °C (range 3) | 48 | ||
| Ambient temperature range | TA | -40 | 85 | °C | Maximum power dissipation (range 6) | 49 | |
| Ambient temperature range | TA | -40 | 105 | °C | Maximum power dissipation (range 7) | 49 | |
| Ambient temperature range | TA | -40 | 125 | °C | Maximum power dissipation (range 3) | 49 | |
| Junction temperature range | TJ | -40 | 105 | °C | -40 °C ≤ TA ≤ 85 °C (range 6) | 49 | |
| Junction temperature range | TJ | -40 | 125 | °C | -40 °C ≤ TA ≤ 105 °C (range 7) | 49 | |
| Junction temperature range | TJ | -40 | 130 | °C | -40 °C ≤ TA ≤ 125 °C (range 3) | 49 | |
| Power on/power down reset threshold | VPOR/PDR | 1 | 1.5 | 1.65 | V | Falling edge | 49 |
| Power on/power down reset threshold | VPOR/PDR | 1.3 | 1.5 | 1.65 | V | Rising edge | 49 |
| Reset temporization | TRSTTEMPO | 2 | 3.3 | ms | VDD rising, BOR enabled | 49 | |
| Brown-out reset threshold 0 | VBOR0 | 1.67 | 1.7 | 1.74 | V | Falling edge | 49 |
| Brown-out reset threshold 0 | VBOR0 | 1.69 | 1.76 | 1.8 | V | Rising edge | 49 |
| Internal reference voltage | VREFINT out | 1.202 | 1.224 | 1.242 | V | -40 °C < TJ < +125 °C | 51 |
| VDDA voltage during VREFINT factory measure | VVREF_MEAS | 2.99 | 3 | 3.01 | V | 51 | |
| Accuracy of factory-measured VREFINT value | AVREF_MEAS | -5 | 5 | mV | Including uncertainties due to ADC and VDDA values | 51 | |
| Temperature coefficient | TCoeff | 25 | 100 | ppm/°C | -40 °C < TJ < +125 °C | 51 | |
| Temperature coefficient | TCoeff | 20 | ppm/°C | 0 °C < TJ < +50 °C | 51 | ||
| Long-term stability | ACoeff | 1000 | ppm | 1000 hours, T= 25 °C | 51 | ||
| Voltage coefficient | VDDCoeff | 2000 | ppm/V | 3.0 V < VDDA < 3.6 V | 51 | ||
| Consumption of reference voltage buffer for ADC | IBUF_ADC | 13.5 | 25 | µA | 51 | ||
| Supply current in Stop mode | IDD (Stop) | 0.34 | 0.99 | µA | TA = -40°C to 25°C | 59 | |
| Supply current in Stop mode | IDD (Stop) | 0.94 | 4.2 | µA | TA= 85°C | 59 | |
| Supply current in Stop mode | IDD (Stop) | 4.9 | 19 | µA | TA = 125°C | 59 | |
| Supply current in Standby mode | IDD (Standby) | 0.23 | 0.6 | µA | Independent watchdog and LSI OFF, TA = -40 °C to 25 °C | 60 | |
| Supply current in Standby mode | IDD (Standby) | 1.35 | 5 | µA | Independent watchdog and LSI OFF, TA = 125 °C | 60 | |
| Data retention mode (minimum supply voltage) | VRM | 1.65 | V | STOP mode (or RESET) | 70 | ||
| Operating voltage (Flash read/write/erase) | VDD | 1.65 | 3.6 | V | Read / Write / Erase | 71 | |
| User external clock source frequency | fHSE_ext | 1 | 8 | 32 | MHz | CSS is ON or PLL is used | 64 |
CAD (KiCad official)
- Symbol:
STM32L011D4P7 - Footprint:
Package_SO:TSSOP-14_4.4x5mm_P0.65mm - 3D model: TSSOP-14 (KiCad packages3D, STEP)
- 3D model files:
stm32l011d4p7-etched.step/stm32l011d4p7-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);stm32l011d4p7.step/stm32l011d4p7.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: STMicroelectronics datasheet (119 pp, sha256
1271aa38a181c7a2, retrieved 2026-10-31, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).